ALTERNATIVE FASTENERS - SRM 51-40-03

Prévia do material em texto

<p>GENERAL - FASTENER SUBSTITUTION</p><p>1. Applicability</p><p>A. Use this chapter-section-subject to find an equivalent fastener or an alternative fastener to replace</p><p>the fastener that was initially installed in the airplane structure. You can also use this</p><p>chapter-section-subject to find replacement fasteners for subsequent repair on the airplane.</p><p>2. General</p><p>A. CDCCL – Refer to WINGS - GENERAL, 57-00-00 for important information on Critical Design</p><p>Configuration Control Limitations (CDCCLs). Fasteners that penetrate the fuel tank must have</p><p>protection against lightning strikes and electrical hot shorts. Refer to LIGHTNING, ELECTRICAL</p><p>WIRING AND EQUIPMENT FAULT CURRENT, AND ELECTROSTATIC DISCHARGE</p><p>REQUIREMENTS, 51-80-01 for specific fastener selection and installation requirements. All content</p><p>in this procedure is CDCCL data. It is very important to the safety requirements of the given AWL.</p><p>NOTE: This is applicable to Airworthiness Limitation 28-AWL-12.</p><p>B. These data have been reviewed by the Boeing Organization Designation Authorization for fuel tank</p><p>ignition prevention requirements, and no further approval from the FAA Oversight Office is required</p><p>to satisfy the requirements of CDCCL 28-AWL-12 provided the repair or alteration is accomplished</p><p>in accordance with these instructions.</p><p>C. When the repairs given in this manual are adapted for in-service repairs, it is possible for the</p><p>operator to use a different type of fastener as an alternative to the fastener specified in the repair</p><p>procedure.</p><p>D. The fastener selection for repairs specified in the Structural Repair Manual or by the engineering</p><p>drawings is based on the data that follows:</p><p>• Strength</p><p>• Corrosion protection</p><p>• Weight</p><p>• Temperature</p><p>• Fatigue properties</p><p>• Method of installation.</p><p>• Prevention of fuel tank ignition sources.</p><p>E. It can be necessary to install alternative fasteners because:</p><p>• The specified fastener is not available</p><p>• It is not easy to get access to a necessary location</p><p>• The special repair is different from the general repair.</p><p>F. Paragraph 4./GENERAL gives definitions and other fastener data that are related to the Fastener</p><p>Substitution Tables given in Fastener Substitution - Rivets, Figure 1/GENERAL, Fastener</p><p>Substitution - Bolts, Figure 2/GENERAL and Fastener Substitution - Lockbolts, Figure 3/GENERAL.</p><p>3. References</p><p>Reference Title</p><p>51-40-06 FASTENER EDGE MARGINS</p><p>51-80-01 LIGHTNING, ELECTRICAL WIRING AND EQUIPMENT FAULT CURRENT,</p><p>AND ELECTROSTATIC DISCHARGE REQUIREMENTS</p><p>57-00-00 WINGS - GENERAL</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 1</p><p>Mar 10/2019D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>4. Fastener Substitution Tables</p><p>A. Table 1/GENERAL gives an index for the Fastener Substitution Tables. Equivalent and alternative</p><p>fasteners are shown by part numbers in different columns in the Fastener Substitution Tables. The</p><p>flagnotes given near the fastener part numbers tell about the permitted use of the equivalent or</p><p>alternative fasteners.</p><p>B. An EQUIVALENT fastener is a fastener which is directly interchangeable with the initial fastener.</p><p>Usually the equivalent fasteners are given under a vendor part number and are not always the same</p><p>as those supplied to the Boeing Company.</p><p>CAUTION</p><p>DO NOT USE THE FASTENER SUBSTITUTION TABLES TO FIND ALTERNATIVES</p><p>FOR THE FASTENERS LISTED IN THE ALTERNATIVE COLUMN. IF YOU DO NOT</p><p>OBEY, THE REPAIR WILL NOT BE APPROVED.</p><p>C. An ALTERNATIVE fastener is a fastener with equal or greater strength properties than the initial</p><p>fastener. However, an alternative fastener cannot be used when:</p><p>(1) They do not give the necessary pressure or fuel seal</p><p>(2) Non-magnetic fasteners are necessary and the fastener is magnetic</p><p>(3) Fastener thread length, grip length or diameter is not available</p><p>(4) Access does not permit fastener installation</p><p>(5) Fastener installation tools are not available.</p><p>(6) It does not provide fuel tank ignition source protection capability per LIGHTNING,</p><p>ELECTRICAL WIRING AND EQUIPMENT FAULT CURRENT, AND ELECTROSTATIC</p><p>DISCHARGE REQUIREMENTS, 51-80-01.</p><p>D. When the equivalent or alternative fastener is used, use the same fastener spacing shown in the</p><p>applicable repair procedure.</p><p>E. Do not use an equivalent or alternative flush-head fastener if the necessary countersink is deeper</p><p>than the initial flush-head fastener.</p><p>F. If an alternative bolt is used, it must have the same locking feature as the initial bolt. Usual locking</p><p>features include a drilled head, drilled shank, or a self-locking nut. For bolts used as alternatives for</p><p>hex-drive bolts or lockbolts that are installed in non-interference holes, an applicable self-locking nut</p><p>must be installed.</p><p>G. Do not use aluminum or alloy steel fasteners as alternatives for titanium or corrosion resistant steel</p><p>fasteners in graphite structures.</p><p>H. The equivalent and alternative fasteners given in the substitution tables can have different electrical</p><p>conductivity than the initial fasteners. If the electrical bonding across the fastener is necessary,</p><p>make sure that the equivalent or alternative fasteners have the necessary electrical conductivity.</p><p>See the Lightning, Electrical Wiring and Equipment Fault Current Requirements in LIGHTNING,</p><p>ELECTRICAL WIRING AND EQUIPMENT FAULT CURRENT, AND ELECTROSTATIC DISCHARGE</p><p>REQUIREMENTS, 51-80-01 for specific fastener selection and installation requirements.</p><p>5. Fasteners Inactive for Boeing Design (Supersessions)</p><p>A. It is possible to continue to use fasteners that are inactive for design in Boeing Airplanes. If you have</p><p>a fastener in stock that a Boeing Fastener Specification shows as superseded, you are permitted to</p><p>use it if the alternative fastener (or fasteners) is a Class I, Class II, IIA, III or IV Supersession.</p><p>B. If a fastener has been superseded by a Class V Supersession, Boeing recommends that you use an</p><p>alternative fastener.</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 2</p><p>Mar 10/2019D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>Table 1:</p><p>FASTENER TYPE REFER TO</p><p>Fastener Substitution - Rivets Figure 1</p><p>Fastener Substitution - Bolts Figure 2</p><p>Fastener Substitution - Lockbolts Figure 3</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 3</p><p>Jul 10/2015D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>_</p><p>H</p><p>G</p><p>P</p><p>O</p><p>N</p><p>J</p><p>K</p><p>M</p><p>L</p><p>I</p><p>A</p><p>B</p><p>F</p><p>E</p><p>D</p><p>C</p><p>THIS FASTENER IS PERMITTED WHEN THE</p><p>DIAMETER IS <5/16 INCH.</p><p>INTERFERENCE REQUIREMENTS. ASK THE BOEING</p><p>REPLACEMENT FASTENER WILL HAVE SPECIAL</p><p>THE INITIAL FASTENER IS USED IN FUEL AREAS</p><p>COMPANY FOR ALTERNATIVE FASTENER AND</p><p>OF THE WING. IT IS POSSIBLE THAT THE</p><p>INSTALLATION INSTRUCTIONS.</p><p>MAGNESIUM STRUCTURES.</p><p>ALTERNATIVES.</p><p>ASK THE BOEING COMPANY FOR FASTENER</p><p>INSTALL TO THE SAME BUTTON DIMENSIONS AS</p><p>THE BACR15GF RIVET.</p><p>SUBSTITUTION FOR REDUCED HEAD RIVET NOT</p><p>MICROSHAVE MONEL RIVETS IN ALUMINUM</p><p>PERMITTED IN ALUMINUM STRUCTURE. DO NOT</p><p>SUBSTITUTION IS NOT PERMITTED IN AREAS</p><p>WOULD TOUCH A PART RADIUS ON THE STRUCTURE.</p><p>REDUCED HEAD FASTENERS ARE NOT PERMITTED AS</p><p>THIS FASTENER IS NOT PERMITTED IN ALUMINUM</p><p>WHERE THE ALTERNATIVE PART RIVET HEAD</p><p>STRUCTURE OR WHERE ELECTRICAL CONDUCTIVITY</p><p>FUSELAGE SKIN AND PRESSURE BULKHEAD</p><p>SUBSTITUTES FOR UNIVERSAL HEAD RIVETS IN</p><p>PERMITTED FOR USE INSIDE THE PRESSURIZED</p><p>THIS FASTENER IS ALLOY STEEL AND IS ONLY</p><p>OF DOME SEAL NUTS, RIGHT ANGLE NUTPLATES,</p><p>FASTENER HOLE DIAMETER UP TO A MAXIMUM OF</p><p>DO NOT USE THESE FASTENERS IN FUEL TANK</p><p>THIS IS NOT APPLICABLE TO THE ATTACHMENT</p><p>THIS IS APPLICABLE TO NUTPLATE ATTACHMENT</p><p>WHERE THE PRIMARY FASTENER IS INSTALLED</p><p>IN A NON-COLD WORKED CLASS 2 OR CLASS 3</p><p>HOLE.</p><p>ATTACHMENT OF NUTPLATES THAT HAVE A PRIMARY</p><p>THE BLIND RIVET IS ONLY APPLICABLE TO THE</p><p>STRUCTURE.</p><p>OR STANDOFFS.</p><p>IS REQUIRED.</p><p>STRUCTURES.</p><p>FUSELAGE ABOVE THE FLOOR.</p><p>AREAS.</p><p>1/4 INCH.</p><p>-</p><p>-</p><p>REFER TO SRM 51-20-01 FOR THE NECESSARY</p><p>REFER TO SRM 51-40-02 FOR THE REMOVAL AND</p><p>TO MAKE SURE THAT THE REPAIR SURFACE IS</p><p>MUST MICRO-SHAVE THE ALTERNATIVE RIVET</p><p>FAIRCHILD</p><p>HI-SHEAR</p><p>WEST COAST</p><p>HL1012AZ</p><p>HL1012AZ</p><p>HL1012AZ</p><p>HL1012AZ</p><p>HL1012AZ</p><p>HL1012AZ</p><p>LUBRICATED,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>CETYL ALCOHOL</p><p>TITANIUM,</p><p>95 KSI SHEAR,</p><p>6AL-4V</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>OR</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACB30NX()K()</p><p>T</p><p>BACN10YT()CD</p><p>BACB30MB()A() M</p><p>BACC30BH()</p><p>BACC30X()</p><p>T</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACB30MB()AK()</p><p>BACN10YT()CD T</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACN10YT()CD TBACB30NX()K()</p><p>OR</p><p>BACC30X()SW</p><p>BACN10HR()CSB F</p><p>R T</p><p>R T</p><p>B F BACN10HR()CS</p><p>BACB30LE()K()</p><p>BACB30MB()AK()</p><p>BACB30LE()K()</p><p>BACB30MB()AK()</p><p>OR</p><p>BACC30BH()SW</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>A L M</p><p>NO EQUIVALENT</p><p>N97138 S0006585362_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 26 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 47</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30NX()K()BACC30CJ() BACC30BH()S</p><p>BACC30M()</p><p>BACC30BL()BACB30VT()K()</p><p>D</p><p>S</p><p>J</p><p>BACB30YK()K()</p><p>BACC30BZ()</p><p>BACC30CK() BACB30NX()K()</p><p>BACN10YR()CD</p><p>BACC30AB()S</p><p>BAC10YR()CM</p><p>D</p><p>BACB30YK()K() BACC30CP()S</p><p>ALLOY 718,</p><p>NICKEL</p><p>LIGHTWEIGHT,</p><p>LUBRICATED,</p><p>PASSIVATED,</p><p>AL COATED,</p><p>SWAGE</p><p>LOCKING</p><p>ALCOHOL</p><p>CETYL</p><p>BACB30XZ()K()</p><p>BACB30XH()K() BACC30CG()6AL-4V</p><p>LIGHTWEIGHT,</p><p>LUBRICATED,</p><p>AL COATED,</p><p>SWAGE</p><p>LOCKING</p><p>ALCOHOL</p><p>CETYL</p><p>TITANIUM,</p><p>BACC30CH()</p><p>BACC30BS()SBACB30VT()K()</p><p>D</p><p>J</p><p>BACB30NX()K() BACC30AB()S</p><p>BACN10YR()CM</p><p>S</p><p>WITH</p><p>BACW10CA()CCU</p><p>AND</p><p>BACW10CA()PVU</p><p>BACB30NX()K() BACC30AB()S</p><p>BACC30CG()</p><p>BACC30CJ()</p><p>TABLE IV</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (TENSION)</p><p>MATING</p><p>PART</p><p>EQUIVALENT</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>ALTERNATIVE MATING PART</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>OR</p><p>BACC30X() A L</p><p>I</p><p>BACB30NX()C() 6AL-4V</p><p>TITANIUM,</p><p>95 KSI SHEAR,</p><p>CADMIUM PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30MB()-()</p><p>BACN10YT()CD</p><p>TBACN30YT()CD</p><p>BACB30MB()A()</p><p>T</p><p>TBACN30YT()CD</p><p>BACB30MB()AK()</p><p>TBACN30YT()CD</p><p>IBACB30NX()K()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97139 S0006585363_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 27 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 48</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>ALLOY 718,</p><p>NICKEL</p><p>GRIT BLAST</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>TOP HEAD,</p><p>PASSIVATED,</p><p>BACB30YK()U()HLT422-()-()</p><p>125 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>ALUMINUM</p><p>LUBRICATED</p><p>COATING,</p><p>PIGMENTED</p><p>HLT422AP HL792BTBACC30CP()S</p><p>HLT422AP</p><p>AIC</p><p>HLT422APALLOY 718,</p><p>HLT422AP HLT792KKBACC30CP()C HI-SHEARNICKELBACB30YK()K()</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (TENSION)</p><p>TABLE IV</p><p>ALTERNATIVE</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>1/64</p><p>OVERSIZE,</p><p>HLT422AP-()-()</p><p>HLT422PB-()-()</p><p>HLT622-()-()</p><p>HLT622AP-()-()</p><p>BACB30YK()K()</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALLUMINUM</p><p>NICKEL</p><p>ALLOY 718,</p><p>INICKEL BACB30YK()K()</p><p>BACB30YK()U()X</p><p>CETYL ALCOHOL</p><p>PLATED,</p><p>CADMIUM</p><p>ALLOY 718,</p><p>LUBRICATED</p><p>NICKEL</p><p>ALLOY 718,</p><p>CETYL ALCOHOL</p><p>PASSIVATED,</p><p>LUBRICATED</p><p>BACB30YK()K()XNICKEL</p><p>LUBRICATED</p><p>1/64 OVERSIZE,</p><p>CETYL ALCOHOL</p><p>ALLOY 718,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>N97140 S0006585364_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 28 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 49</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>G</p><p>G I</p><p>I</p><p>HLT422AP()-()</p><p>BACB30YK()K()</p><p>BACB30YK()K()</p><p>HLT422AP()-()</p><p>I</p><p>I</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (TENSION)</p><p>TABLE IV</p><p>HLT716-()-() NICKEL BACB30YK()U()Y</p><p>ALLOY 718,</p><p>BACB30YK()K()YHLT716PB-()-() NICKEL</p><p>CETYL ALCOHOL</p><p>PLATED,</p><p>ALLOY 718,</p><p>1/32 OVERSIZE,</p><p>CADMIUM</p><p>LUBRICATED</p><p>HLT716AP-()-() BACB30YK()K()YNICKEL</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>1/32 OVERSIZE,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>ALLOY 718,</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>1/32 OVERSIZE,</p><p>PASSIVATED,</p><p>ALCOHOL</p><p>LUBRICATED</p><p>FILM, CETYL</p><p>HL646PB-()-()</p><p>HL646TB-()-()</p><p>STAINLESS</p><p>CETYL ALCOHOL</p><p>PLATED,</p><p>STEEL, CADMIUM</p><p>PH13-8Mo</p><p>LUBRICATED</p><p>PH13-8Mo</p><p>STAINLESS</p><p>STEEL, SOLID</p><p>ALTERNATIVE</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>I</p><p>HLT622PB-()-()</p><p>PLATED,</p><p>CADMIUM</p><p>1/64 OVERSIZE,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>IBACB30YK()K()X</p><p>ALLOY 718,</p><p>NICKEL NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97141 S0006585365_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 29 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 50</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>MATING</p><p>PART</p><p>EQUIVALENT MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>100 ˚ (AN509)</p><p>PLATED,</p><p>CADMIUM</p><p>TENSION,</p><p>CETYL ALCOHOL</p><p>HEAD,160 KSI</p><p>BACB30JC()-() ALLOY STEEL, BACB30NY()K()</p><p>ALTERNATIVE</p><p>SPS</p><p>HUCK</p><p>FAIRCHILD</p><p>HI-SHEAR</p><p>HL21PB</p><p>HL21PB</p><p>HL21PB</p><p>HL21PB</p><p>HL21PB</p><p>HL21PB</p><p>AIC</p><p>WEST COAST</p><p>BACC30X()</p><p>OR</p><p>BACC30BH()</p><p>BACB30NY()K()BACC30Z()</p><p>BACN10YT()CD</p><p>BACB30NY()K()</p><p>SPS</p><p>HUCK</p><p>HL449UC</p><p>HL449UC</p><p>HL449UC</p><p>HL449UC</p><p>HI-SHEAR HL449UC</p><p>AIC</p><p>HL449UCWEST COAST</p><p>100 ˚ (AN509)</p><p>LUBRICATED,</p><p>TENSION,</p><p>CADMIUM</p><p>PLATED,</p><p>CETYL ALCOHOL</p><p>HEAD, 160 KSI</p><p>A286 CRES,BACB30JC()A() BACC30X()</p><p>OR</p><p>BACC30BH()</p><p>BACB30JC()A()U</p><p>A286 CRES,</p><p>ALUMINUM</p><p>COATED, CETYL</p><p>ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>HI-SHEAR HL449AZ</p><p>DEUTSCH</p><p>SPS</p><p>WEST COAST HL449AZ</p><p>BACN10YT()CD</p><p>BACB30JC()-()</p><p>BACB30JC()AK() BACN10YT()CD</p><p>BACN10YT()CD</p><p>BACB30JC()A()</p><p>BACN10YT()CD</p><p>BACB30NY()K()</p><p>NAS1805-()PBACB30LP()U()BACC30X()P</p><p>PASSIVATED,</p><p>160 KSI</p><p>TENSION,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>100 ˚ (AN509)</p><p>HEAD,</p><p>A286 CRES, AIC</p><p>HI-SHEAR</p><p>SPS</p><p>DEUTSCH</p><p>WEST COAST</p><p>HL49</p><p>HL49</p><p>HL49</p><p>HL49</p><p>HL49</p><p>HL49</p><p>BOLT - HEX DRIVE - FLUSH HEAD (TENSION)</p><p>NAS1805-()PBACB30LR()U()</p><p>TABLE V</p><p>BACC30X()</p><p>OR</p><p>BACC30BH()</p><p>BACB30JC()AK()</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>900 ˚F (482˚C)</p><p>LUBRICATED</p><p>450 ˚F (232˚C)</p><p>BACNYT()CD</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30BH()P</p><p>BACC30X()P</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>HL449AZ</p><p>HL449AZ</p><p>HL449AZ</p><p>100 ˚ (AN509)</p><p>TENSION,</p><p>HEAD, 160 KSI</p><p>FAIRCHILD</p><p>FAIRCHILD</p><p>FAIRCHILD</p><p>F</p><p>F</p><p>R T</p><p>R T</p><p>I</p><p>AA</p><p>I</p><p>T</p><p>I</p><p>AA</p><p>M</p><p>T</p><p>A L</p><p>T</p><p>T</p><p>T</p><p>AA</p><p>T</p><p>M</p><p>Q</p><p>N97142 S0006585366_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 30 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 51</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>MATING</p><p>PART</p><p>EQUIVALENT MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>ALTERNATIVE</p><p>TABLE V</p><p>BOLT - HEX DRIVE - FLUSH HEAD (TENSION)</p><p>6AL-4V</p><p>160 KSI</p><p>TITANIUM,</p><p>TENSION,</p><p>BACB30NY()C()</p><p>CADMIUM PLATED,</p><p>CETYL ALCOHOL,</p><p>LUBRICATED</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACN10YT()CD</p><p>BACB30JC()-()</p><p>BACN10YT()CD</p><p>BACB30JC()A()</p><p>BACN10YT()CD</p><p>BACB30JC()AK()</p><p>BACN10YT()CD</p><p>BACB30NY()K()</p><p>AIC</p><p>ALCOA</p><p>HUCK</p><p>SPS</p><p>WEST COAST</p><p>HL1013AZ</p><p>HL1013AZ</p><p>HL1013AZ</p><p>HL1013AZ</p><p>HL1013AZ</p><p>HL1013AZ</p><p>HI-SHEAR</p><p>BACN10YT()CD</p><p>BACB30JC()-()6AL-4V</p><p>160 KSI</p><p>TITANIUM,</p><p>TENSION,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACB30NY()K()</p><p>BACC30X()</p><p>OR</p><p>BACC30BH()</p><p>BACC30X()</p><p>OR</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACN10YT()CD</p><p>BACB30JC()A()</p><p>BACB30JC()AK()</p><p>BACN10YT()CD</p><p>BACN10YT()CDBACB30NY()K()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>L M</p><p>6AL-4V</p><p>TITANIUM,</p><p>100 ˚ HEAD,</p><p>LIGHTWEIGHT,</p><p>95 KSI</p><p>SHEAR, AL</p><p>COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SWAGE</p><p>LOCKING</p><p>BACB30XF()K() BACB30NY()K()BACC30CG()</p><p>NAS1805-()</p><p>WITH</p><p>BACW10CA()CCU</p><p>AND</p><p>BACW10CA()PVU</p><p>BACC30AB()S</p><p>BACB30NY()K()</p><p>BACB30NY()K()</p><p>BACB30NY()K() BACC30M()</p><p>BACC30BH()S</p><p>BACC30CH()</p><p>BACC30CJ()</p><p>BACC30CK()</p><p>T</p><p>T</p><p>T</p><p>T</p><p>H AA</p><p>T</p><p>A L</p><p>T</p><p>T</p><p>I</p><p>T</p><p>I</p><p>A</p><p>AA</p><p>M</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97143 S0006585367_V3</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 31 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 52</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>ALLOY 718,</p><p>NICKEL HI-SHEAR</p><p>HLT423AP</p><p>AIC</p><p>125 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>COATING,</p><p>BACC30CP()C</p><p>BACC30CP()S</p><p>HLT423AP</p><p>100 ˚ HEAD,</p><p>BACB30YM()K()</p><p>HL792BT</p><p>HL792KK</p><p>HLT423AP</p><p>HLT423AP</p><p>ALLOY 718,</p><p>100 ˚ HEAD,</p><p>LIGHTWEIGHT,</p><p>PASSIVATED,</p><p>AL COATED,</p><p>CETYL</p><p>ALCOHOL</p><p>LUBRICATED,</p><p>SWAGE</p><p>LOCKING</p><p>NICKEL BACC30CJ()BACB30XY()K() BACC30CP()SBACB30YM()K()</p><p>ALTERNATIVE</p><p>BOLT - HEX DRIVE - FLUSH HEAD (TENSION)</p><p>TABLE V</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>NICKEL BACB30YM()U()</p><p>HLT423AP-()-()</p><p>HLT423-()-()</p><p>CETYL ALCOHOL</p><p>PASSIVATED,</p><p>OF HEAD,</p><p>BLAST TOP</p><p>HEAD, GRIT</p><p>(MS24694)</p><p>100 ˚ FLUSH</p><p>NICKEL</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>(MS24694)</p><p>HEAD,</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>LUBRICATED</p><p>ALLOY 718,</p><p>BACB30YM()K()</p><p>HLT423PB-()-() NICKEL BACB30YM()K() I</p><p>CETYL ALCOHOL</p><p>(MS24694)</p><p>CADMIUM</p><p>PLATED,</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>HEAD,</p><p>LUBRICATED</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97144 S0006585368_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 32 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 53</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BOLT - HEX DRIVE - FLUSH HEAD (TENSION)</p><p>TABLE V</p><p>ALTERNATIVE</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>HLT623AP-()-()</p><p>HLT623-()-()</p><p>BACB30YM()K()X</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>NICKEL</p><p>HEAD,</p><p>(MS24694)</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>1/64 OVERSIZE,</p><p>(MS24694)</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>NICKEL</p><p>CETYL ALCOHOL</p><p>PASSIVATED,</p><p>1/64 OVERSIZE,</p><p>HEAD,</p><p>LUBRICATED</p><p>BACB30YM()U()X</p><p>(MS24694)</p><p>CETYL ALCOHOL</p><p>CADMIUM</p><p>PLATED,</p><p>HEAD,</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>1/64 OVERSIZE,</p><p>LUBRICATED</p><p>NICKEL BACB30YM()K()XHLT623PB-()-() INO EQUIVALENT</p><p>N97145 S0006585369_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 33 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 54</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>HLT717PB-()-() BACB30YM()K()YNICKEL</p><p>SIZE,</p><p>1/32 OVER-</p><p>HEAD,</p><p>CETYL ALCOHOL</p><p>PLATED,</p><p>CADMIUM</p><p>(MS24649)</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>I</p><p>LUBRICATED</p><p>ALTERNATIVE</p><p>BOLT - HEX DRIVE - FLUSH HEAD (TENSION)</p><p>TABLE V</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>CETYL ALCOHOL</p><p>PASSIVATED,</p><p>HEAD,</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>1/32 OVERSIZE,</p><p>NICKEL</p><p>(MS24649)</p><p>LUBRICATED</p><p>BACB30YM()U()YHLT717-()-()</p><p>NICKELHLT717AP-()-()</p><p>HEAD,</p><p>(MS24694)</p><p>100 ˚ FLUSH</p><p>ALLOY 718,</p><p>ALUMINUM</p><p>1/32 OVERSIZE,</p><p>BACB30YM()K()Y</p><p>PIGMENTED</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>NO EQUIVALENT</p><p>N97146 S0006585370_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 34 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 55</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>MATING</p><p>PART</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>TABLE VI</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>I</p><p>I</p><p>I</p><p>I</p><p>BACB30LE()-()</p><p>BACB30LE()K()</p><p>B</p><p>BACB30LJ()-()</p><p>BACB30LM()-()</p><p>BACB30LT()-()</p><p>BACB30NE()-() A L</p><p>BACB30NR()K()</p><p>I</p><p>V</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>NAS6703 THRU NAS6720</p><p>B</p><p>I</p><p>B</p><p>ALLOY STEEL, BACB30LE()-()</p><p>BACB30LE()K()</p><p>12 POINT HEAD,</p><p>180 KSI</p><p>TENSION,</p><p>PLATED,</p><p>CADMIUM</p><p>FLUOBORATE</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30FD()-()</p><p>HEX CLOSE TOL</p><p>160,000 PSI</p><p>SHORT THREAD</p><p>BACB30GE()-()</p><p>CADMIUM</p><p>LONG THREAD,</p><p>200 KSI</p><p>TENSION,</p><p>12 POINT HEAD,</p><p>PLATED, BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30LE()K()A286 CRES,BACB30LE()-()</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30NF()-()</p><p>BACB30MR()K() IB</p><p>BACB30NM()K() I</p><p>IB</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97147 S0006585371_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 35 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 56</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACN10HR()CD</p><p>BACN10HR()CD</p><p>BACN10HR()CD</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30LE()-()</p><p>BACB30US()K()D</p><p>OR</p><p>MS14144</p><p>OR</p><p>BACN11N()</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TENSILE</p><p>200 KSI</p><p>LONG THREAD</p><p>12 POINT HEAD,</p><p>110 KSI SHEAR,</p><p>BACN10HR()CD</p><p>M</p><p>M</p><p>A286 CRES, BACN10JD() X</p><p>BACB30LE()K()</p><p>BACB30LE()DK()</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>R</p><p>R</p><p>R</p><p>BACB30MR()K()</p><p>BACB30NM()K()</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PART</p><p>PART</p><p>MATING</p><p>NAS6703 THRU NAS6720</p><p>BACB30NE()D()</p><p>BACB30LT()D()</p><p>BACB30LM()D()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30NR()K()</p><p>BACB30LE()DK()</p><p>BACB30LE()-()</p><p>BACB30LT()-()</p><p>BACB30LM()-()</p><p>BACB30LE()K()</p><p>MS14145</p><p>OR</p><p>BACN11N()</p><p>OR</p><p>NAS6703D THRU</p><p>NAS6720D</p><p>BACB30US()K()D IB</p><p>A</p><p>X</p><p>X</p><p>X</p><p>X</p><p>X</p><p>IB</p><p>B</p><p>I</p><p>BACB30LJ()D()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>A286 CRES,</p><p>DRILLED SHANK,</p><p>HEX HEAD,</p><p>95 KSI SHEAR,</p><p>SHORT THREAD,</p><p>CADMIUM</p><p>PLATED,</p><p>BACN10JD() IB X</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30LJ()-() A286 CRES, B</p><p>IB</p><p>PLATED,</p><p>HEX HEAD,</p><p>95 KSI SHEAR,</p><p>SHORT THREAD,</p><p>CADMIUM</p><p>900 ˚F (482˚C)</p><p>TEMP</p><p>BACB30LE()U() BACB30US()-()</p><p>LONG THREAD,</p><p>TENSION, MAX</p><p>A286 CRES,</p><p>PASSIVATED,</p><p>12 POINT HEAD,</p><p>200 KSI</p><p>IB</p><p>I</p><p>U</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97148 S0006585372_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 36 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 57</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30LJ()SU() BACB30LJ()U()A286 CRES,</p><p>B</p><p>B</p><p>B</p><p>BACB30LM()U()</p><p>BACB30LT()U()</p><p>BACB30LM()SU()</p><p>BACB30LE()U()</p><p>BACB30PN()-()</p><p>BACB30US()-()</p><p>NAS6703U THRU NAS6720U</p><p>HEX HEAD,</p><p>DRY FILM</p><p>SHORT THREAD,</p><p>PASSIVATED,</p><p>95 KSI SHEAR,</p><p>LUBRICATED,</p><p>BACB30LJ()U()</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>B</p><p>B</p><p>B</p><p>BACB30LT()U()</p><p>BACB30LE()U()</p><p>BACB30PN()-()</p><p>BACB30US()-()</p><p>NAS6703U THRU NAS6720U</p><p>BACB30LM()U()</p><p>HEX HEAD,</p><p>95 KSI SHEAR,</p><p>SHORT THREAD,</p><p>PASSIVATED,</p><p>A286 CRES,</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PART</p><p>PART</p><p>MATING</p><p>BACB30LE()-()</p><p>BACB30LT()K()</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>BACB30LE()K()</p><p>BACB30LE()U()</p><p>BACB30US()-()</p><p>BACB30PN()-()</p><p>BACB30LE()U()</p><p>BACB30LM()U()</p><p>NAS6703U THRU</p><p>NAS6720U</p><p>BACB30US()-()</p><p>BACB30PN()-()</p><p>BACB30NM()K()</p><p>BACB30LE()K()</p><p>BACB30MR()K()</p><p>BACB30LE()-()</p><p>BACB30US()K()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BA286 CRES,BACB30LT()-()</p><p>IB</p><p>I</p><p>I</p><p>B</p><p>B</p><p>CADMIUM PLATED,</p><p>110 KSI SHEAR,</p><p>SHORT THREAD,</p><p>12 POINT HEAD,</p><p>B</p><p>B</p><p>B</p><p>B</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>BACB30LM()U() A286 CRES,</p><p>PASSIVATED,</p><p>160 KSI TENSION,</p><p>LONG THREAD,</p><p>HEX HEAD,</p><p>NAS672OU</p><p>NAS6703U THRU</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30LM()SU() A286 CRES,</p><p>LUBRICATED,</p><p>DRY FILM</p><p>160 KSI TENSION,</p><p>LONG THREAD,</p><p>HEX HEAD,</p><p>PASSIVATED,</p><p>B</p><p>B</p><p>I</p><p>IB</p><p>IB</p><p>B</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>IB</p><p>NAS6720CADMIUM</p><p>HEX HEAD,</p><p>160 KSI TENSION,</p><p>LONG THREAD,</p><p>NAS6703 THRUBACB30LM()-() A286 CRES,</p><p>PLATED,</p><p>U</p><p>U</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97149 S0006585373_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 37 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 58</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>OR</p><p>MS14145</p><p>OR</p><p>BACN11N()</p><p>BACN10JD</p><p>BACN10JD()</p><p>H</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>BACB30MR()K()</p><p>BACB30LE()K()</p><p>BACB30LE()-()</p><p>BACB30LE()K()</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>NO ALTERNATIVE</p><p>BACB30LT()-()</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>BACB30US()K()D</p><p>BACB30LT()D()</p><p>I</p><p>I</p><p>I</p><p>OR</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>BACB30MR()K() 6AL-4V</p><p>TITANIUM,</p><p>12 POINT HEAD,</p><p>95 KSI SHEAR,</p><p>LONG THREAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>M</p><p>M</p><p>BACB30MR()C()</p><p>450 ˚F (232˚C)</p><p>1200˚F (649˚C)</p><p>BACB30LT()DU()</p><p>BACB30LT()U() BACN10JC()CMA286 CRES,</p><p>THREADED. 95</p><p>KSI MAX TEMP</p><p>LONG</p><p>POINT, HEAD</p><p>PLATED, 12</p><p>TITANIUM, CAD</p><p>6AL-4V</p><p>BACN10YR()CM</p><p>MAX TEMP</p><p>SHORT THREAD,</p><p>110 KSI SHEAR,</p><p>12 POINT HEAD,</p><p>CLOSE</p><p>TOLERANCE,</p><p>PASSIVATED,</p><p>OR</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>BACB30LT()K() A286 CRES, M</p><p>110 KSI SHEAR,</p><p>12 POINT HEAD,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TOLERANCE,</p><p>CLOSE</p><p>SHORT THREAD, M</p><p>B</p><p>B</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>XB</p><p>BACB30LT()DK()</p><p>COATING,</p><p>XMA286 CRES,</p><p>DRILLED SHANK,</p><p>CLOSE</p><p>SHORT THREAD,</p><p>110 KSI SHEAR,</p><p>12 POINT HEAD,</p><p>TOLERANCE,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PART</p><p>PART</p><p>MATING</p><p>BACN11N()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97150 S0006585374_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 38 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 59</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30US()K()D</p><p>BACB30LE()DK()</p><p>BACB30US()P()</p><p>BACB30US()P()</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>BACB30MT()T() E H-11 STEEL,</p><p>12 POINT HEAD,</p><p>220 KSI TENSION,</p><p>LONG THREAD,</p><p>PLATED,</p><p>NICKEL-CADMIUM</p><p>DIFFUSED</p><p>BACB30US()K() KI</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>KIEBACB30MT()L()</p><p>LONG THREAD,</p><p>220 KSI TENSION,</p><p>12 POINT HEAD,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>H-11 STEEL, BACB30US()K()</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>DRILLED HEAD</p><p>125 KSI SHEAR</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>BACB30MT()-()</p><p>BACB30US()K()H</p><p>M</p><p>EBACB30MT()K() H-11 STEEL, BACB30US()K()</p><p>PIGMENTED</p><p>ALUMINUM</p><p>LONG THREAD,</p><p>12 POINT HEAD,</p><p>COATING,</p><p>220 KSI TENSION,</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>220 KSI TENSION,</p><p>12 POINT HEAD,</p><p>H-11 STEEL BOLT,</p><p>E</p><p>E</p><p>BACB30MT()HT()</p><p>BACB30MT()HL()</p><p>BACB30MT()HK()</p><p>BACB30MT()H()</p><p>H-11 STEEL BOLT,</p><p>125 KSI SHEAR</p><p>220 KSI TENSION,</p><p>12 POINT HEAD,</p><p>MS14144</p><p>OR</p><p>BACN11N()</p><p>OR</p><p>BACN10JD()BACB30MR()DK()</p><p>TITANIUM,</p><p>12 POINT HEAD,</p><p>95 KSI SHEAR,</p><p>LONG THREAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>DRILLED SHANK,</p><p>6AL-4V X</p><p>X</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>E</p><p>E</p><p>E</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97151 S0006585375_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 39 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 60</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30NE()-() LA</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>TENSION,</p><p>BACB30NH()-()</p><p>CADMIUM PLATE,</p><p>PH13-8Mo CRES,</p><p>12 POINT HEAD,</p><p>LONG THREAD,</p><p>220 KSI</p><p>G</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>CADMIUM</p><p>PLATED,</p><p>95 KSI SHEAR,</p><p>SHORT THREAD,</p><p>BACB30NF()-()</p><p>HEX HEAD,</p><p>ALLOY STEEL,</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30NE()-()</p><p>TENSION,</p><p>160 KSI</p><p>LONG THREAD,</p><p>HEX HEAD,</p><p>CADMIUM PLATED,</p><p>ALLOY STEEL, NAS6603 THRU</p><p>NAS6620</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>NAS6703 THRU NAS6720</p><p>NAS6603 THRU NAS6620</p><p>BACB30LJ()-()</p><p>BACB30LM()-()</p><p>BACB30LT()-()</p><p>BACB30NR()K()</p><p>BACB30LE()-()</p><p>BACB30LE()K()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30US()K() I</p><p>I V</p><p>B</p><p>IB</p><p>IB</p><p>B</p><p>BACB30LM()-()</p><p>BACB30MR()K() IB</p><p>BACB30LE()-()</p><p>BACB30LE()K()</p><p>B</p><p>IB</p><p>BACB30NM()K() I</p><p>IB</p><p>BBACB30US()P()</p><p>NAS6703 THRU NAS6720</p><p>BACB30US()K()</p><p>BACB30MR()K() IB</p><p>BACB30NM()K() I</p><p>BACB30US()K() I</p><p>TENSION,</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>BACB30NH()U() BACB30US()-()</p><p>220 KSI</p><p>12 POINT HEAD,</p><p>PASSIVATED,</p><p>LONG THREAD,</p><p>G PH13-8Mo CRES,</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97152 S0006585376_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 40 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 61</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>M</p><p>K</p><p>BBACB30US()P()</p><p>BBACB30US()P()</p><p>BACB30US()K() I</p><p>BACB30US()P() KB</p><p>BACB30NL()-()</p><p>BACB30NJ()L()</p><p>BACB30NJ()K()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>IBACB30US()K() B</p><p>BACB30US()K() B I</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>PH13-8Mo CRES,</p><p>CADMIUM PLATED,</p><p>125 KSI SHEAR,</p><p>12 POINT HEAD,</p><p>SHORT THREAD,</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>125 KSI SHEAR</p><p>SHORT THREAD,</p><p>12 POINT HEAD,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>H-11 STEEL,</p><p>BBACB30US()P()</p><p>BBACB30US()K()</p><p>ALUMINUM</p><p>H-11 STEEL,</p><p>SHORT THREAD,</p><p>125 KSI SHEAR,</p><p>12 POINT HEAD,</p><p>COATING,</p><p>PIGMENTED</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>BACB30US()K() IB</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>BACB30NJ()-()</p><p>PLATED,</p><p>DIFFUSED</p><p>12 POINT HEAD,</p><p>SHORT THREAD,</p><p>125 KSI SHEAR,</p><p>H-11 STEEL,</p><p>NICKEL-CADMIUM</p><p>BACB30NH()SU() PH13-8Mo CRES, BACB30US()-()</p><p>DRY FILM</p><p>220 KSI TENSION,</p><p>12 POINT HEAD,</p><p>PASSIVATED,</p><p>LONG THREAD,</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>G</p><p>E</p><p>E</p><p>E</p><p>G</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97153 S0006585377_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 41 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 62</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>B</p><p>IB</p><p>I</p><p>I</p><p>IB</p><p>IB</p><p>B M</p><p>B</p><p>B M</p><p>B</p><p>B</p><p>B</p><p>IB</p><p>I</p><p>B I</p><p>H</p><p>B</p><p>B</p><p>B IH</p><p>G</p><p>G</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>BACB30NM()K()</p><p>BACB30NR()K()</p><p>BACB30LE()-()</p><p>BACB30LE()K()</p><p>BACB30MR()K()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30LE()K()</p><p>BACB30MR()K()</p><p>BACB30MR()K()</p><p>BACB30NM()K()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>BACB30US()-()</p><p>BACB30US()-()</p><p>BACB30LE()K()</p><p>BACB30NR()C()</p><p>BACB30NM()K()</p><p>6AL-4V</p><p>TITANIUM,</p><p>CADMIUM PLATED,</p><p>HEX HEAD, SHORT</p><p>THREAD, 95</p><p>KSI SHEAR, MAX</p><p>TEMP 450 ˚F</p><p>(232˚C)</p><p>6AL-4V</p><p>TITANIUM,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>HEX HEAD,</p><p>LONG THREAD,</p><p>160 KSI</p><p>TENSION,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACB30NM()C()</p><p>6AL-4V</p><p>TITANIUM,</p><p>CADMIUM PLATED,</p><p>HEX HEAD, LONG</p><p>THREAD, 160</p><p>KSI TENSION,</p><p>MAX TEMP 450 ˚F</p><p>(232˚C)</p><p>BACB30NL()U() PH13-8Mo CRES,</p><p>PASSIVATED,</p><p>12 POINT HEAD,</p><p>SHORT THREAD,</p><p>125 KSI SHEAR,</p><p>MAX TEMP</p><p>600 ˚F (316˚C)</p><p>BACB30NL()SU() PH13-8Mo CRES,</p><p>PASSIVATED,</p><p>12 POINT HEAD,</p><p>SHORT THREAD,</p><p>125 KSI SHEAR,</p><p>DRY FILM</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MATING</p><p>PART</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>N97154 S0006585378_V3</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 42 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 63</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>I</p><p>K</p><p>BACB30NM()K()</p><p>BACB30LT()-()</p><p>BACB30LE()K()</p><p>BACB30MR()K()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30LE()-()</p><p>BACB30US()K()H</p><p>BACB30US()K()</p><p>BACB30US()-()</p><p>BACB30US()K()</p><p>BACB30LE()U()</p><p>BACB30US()P()H</p><p>M</p><p>M</p><p>B</p><p>M</p><p>B</p><p>B</p><p>B</p><p>B</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>BACB30TR()K()</p><p>ALUMINUM</p><p>125 KSI SHEAR,</p><p>TENSION,</p><p>220 KSI</p><p>PROFILE HEAD,</p><p>12 POINT LOW</p><p>PIGMENTED</p><p>COATING,</p><p>E H-11 STEEL,</p><p>600 ˚F (316˚C)</p><p>BACB30TR()HT() E</p><p>DRILLED HEAD</p><p>LOW PROFILE,</p><p>SHEAR 12 POINT</p><p>MIN TENSILE</p><p>125 KSI MIN</p><p>H-11STEEL,</p><p>DIFFUSED</p><p>NICKEL-CADMIUM</p><p>PLATED, 220 KSI</p><p>1200˚F (649˚C)</p><p>BACB30PN()-()</p><p>I</p><p>MAX TEMP</p><p>LONG THREAD,</p><p>12 POINT HEAD,</p><p>INCONEL 718,</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>BACB30NR()K() 6AL-4V</p><p>TITANIUM,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>HEX HEAD,</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>U</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97155 S0006585379_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 43 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 64</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING</p><p>HEAD</p><p>TABLE VI</p><p>PART NUMBER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>BACB30US()K() BACN10HR()CD</p><p>BACB30US()K()</p><p>BACN10HR()CD</p><p>OR</p><p>BACN10HR</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>M</p><p>I</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>BACB30US()P() RINICKEL</p><p>CADMIUM</p><p>LONG THREAD,</p><p>125 KSI SHEAR,</p><p>TENSILE,</p><p>220 KSI</p><p>12 POINT HEAD,</p><p>ALLOY 718,</p><p>PLATED,</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>BACB30US()K()</p><p>COATED,</p><p>BMS 10-85</p><p>125 KSI SHEAR,</p><p>LONG THREAD,</p><p>12 POINT HEAD,</p><p>INCONEL 718,</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>BACB30TR()T() E H-11 STEEL,</p><p>125 KSI SHEAR,</p><p>TENSION,</p><p>220 KSI</p><p>PROFILE HEAD,</p><p>12 POINT LOW</p><p>PLATED,</p><p>CADMIUM</p><p>NICKEL</p><p>DIFFUSED</p><p>BACB30TR()L()</p><p>PIGMENTED</p><p>ALUMINUM</p><p>COATING,</p><p>PROFILE HEAD,</p><p>12 POINT LOW</p><p>125 KSI SHEAR,</p><p>TENSION,</p><p>220 KSI</p><p>H-11 STEEL, IE NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97156 S0006585380_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 44 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 65</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30XJ()K()</p><p>ALUMINUM</p><p>LONG THREAD,</p><p>TENSILE,</p><p>150 KSI</p><p>HEX HEAD,</p><p>TITANIUM,</p><p>PIGMENTED</p><p>NAS1805-()LNAS1805-()L6AL-4V</p><p>COATING</p><p>BACB30XL()K()</p><p>BACB30UU()K()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30UU()P()</p><p>BACB30US()P()</p><p>BACB30US()K()</p><p>BACB30US()-()</p><p>M</p><p>I</p><p>IB</p><p>B</p><p>M</p><p>B</p><p>B</p><p>450 ˚F (232˚C)</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>MAX TEMP</p><p>B R</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>BACB30UU()K() INCONEL 718,</p><p>COATING,</p><p>PIGMENTD</p><p>125 KSI SHEAR,</p><p>SHORT THREAD,</p><p>12 POINT HEAD,</p><p>ALUMINUM</p><p>1200˚F (649˚C)</p><p>BACB30UU()P() NICKEL</p><p>ALLOY 718,</p><p>12 POINT HEAD,</p><p>125 KSI SHEAR,</p><p>SHORT THREAD,</p><p>CLOSE</p><p>TOLERANCE,</p><p>CADMIUM</p><p>PLATED,</p><p>BACB30UU()-() BINCONEL 718,</p><p>PASSIVATED,</p><p>12 POINT HEAD,</p><p>SHORT THREAD,</p><p>125 KSI SHEAR,</p><p>MAX TEMP</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97157 S0006585381_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 45 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 66</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>TITANIUM,</p><p>150 KSI</p><p>TENSILE,</p><p>90 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>12 POINT HEAD,</p><p>6AL-4V NO ALTERNATIVEBACB30XL()K() NAS1805-()L</p><p>BACB30XJ()K()</p><p>BACB30XL()K()</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING</p><p>90 KSI SHEAR,</p><p>SHORT THREAD,</p><p>6AL-4V</p><p>TITANIUM,</p><p>HEX HEAD,</p><p>BACB30XN()K()</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>A</p><p>B</p><p>L</p><p>I</p><p>B</p><p>BACB30LJ()-()</p><p>BACB30LM()-()</p><p>BACB30LT()-()</p><p>BACB30NE()-()</p><p>BACB30LE()-()</p><p>BACB30LE()K()</p><p>BACB30NR()K()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>NAS6603 THRU NAS6620</p><p>NAS6703 THRU NAS6720</p><p>PART</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PART</p><p>MATING</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>B</p><p>BACB30ZB()-()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>CADMIUM</p><p>PLATED,</p><p>HEX HEAD,</p><p>ALLOY STEEL,</p><p>VI</p><p>IB</p><p>B</p><p>TABLE VI</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>BACB30NF()-()</p><p>SHORT THREAD,</p><p>CLOSE TOLERANCE</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97158 S0006585382_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 46 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 67</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30LE()K()</p><p>BACB30LE()-()</p><p>BACB30NE()-()</p><p>BACB30LT()-()</p><p>BACB30LM()-()</p><p>BACB30LJ()-()</p><p>BACB30US()K()</p><p>BACB30NR()K()</p><p>BACB30NF()-()</p><p>BACB30LM()-()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>PLATED,</p><p>CADMIUM</p><p>HEX HEAD,</p><p>TENSION,</p><p>160 KSI</p><p>LONG THREAD,</p><p>A286 CRES,</p><p>NAS6720</p><p>NAS6703 THRU</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PART</p><p>ALLOY STEEL,</p><p>HEX HEAD,</p><p>SHORT THREAD,</p><p>B I</p><p>B</p><p>A L</p><p>NAS1103 THRU</p><p>NAS1120</p><p>PLATED,</p><p>CADMIUM</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>B I</p><p>I V</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>NAS6603 THRU ALLOY STEEL,</p><p>TENSION</p><p>160 KSI</p><p>LONG THREAD,</p><p>HEX HEAD,</p><p>CADMIUM PLATED,</p><p>BACB30NE()-()</p><p>NAS6620</p><p>TABLE VI</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>PART</p><p>MATING</p><p>BACB30LM()-()</p><p>BACB30US()P()</p><p>BBACB30US()K() I</p><p>BBACB30US()P()</p><p>NAS6703 THRU NAS6720</p><p>B</p><p>BACB30NM()K() I</p><p>BACB30NF()-()</p><p>BACB30MR()K() IB</p><p>BACB30LE()-()</p><p>BACB30LE()K() IB</p><p>B</p><p>BACB30US()P()</p><p>BACB30ZB()-()</p><p>B</p><p>NAS6703 THRU NAS6720</p><p>NAS6603 THRU NAS6620</p><p>NO EQUIVALENT</p><p>N97159 S0006585383_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 47 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 68</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30NM()DK()</p><p>NAS6703-() THRU</p><p>NAS6720-()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>BACB30NM()K()</p><p>BACB30MR()K()</p><p>BACB30LM()-()</p><p>BACB30LE()K()</p><p>BACB30LE()-()</p><p>BACB30LE()U()</p><p>BACB30US()-()</p><p>BACB30PN()-()</p><p>MATING</p><p>PART</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>TABLE VI</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>M N</p><p>NAS6703D() THRU</p><p>NAS6720D()</p><p>NAS6703AD() THRU</p><p>NAS6720AD()</p><p>NON-LOCKING</p><p>A-286 CRES,</p><p>HEX HEAD,</p><p>CLOSE</p><p>TOLERANCE,</p><p>160 KSI</p><p>TENSILE,</p><p>95 KSI SHEAR,</p><p>LONG THREAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>DRILLED,</p><p>M</p><p>B</p><p>B</p><p>M</p><p>B</p><p>M</p><p>B</p><p>B MNAS6703A() THRU</p><p>NAS6720A() HEX HEAD,</p><p>CLOSE</p><p>TOLERANCE,</p><p>160 KSI</p><p>TENSILE,</p><p>95 KSI SHEAR,</p><p>LONG THREAD,</p><p>UNDRILLED,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>A-286 CRES,</p><p>NON-LOCKING</p><p>B</p><p>B</p><p>B</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>NAS6720U</p><p>NAS6703U THRU BACB30LM()U()A286 CRES,</p><p>PASSIVATED,</p><p>TENSION,</p><p>160 KSI</p><p>LONG THREAD,</p><p>HEX HEAD,</p><p>OR</p><p>OR</p><p>BACN10JD()</p><p>MS14144</p><p>BACN11N()</p><p>X</p><p>U</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97160 S0006585384_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 48 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 69</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>I</p><p>I</p><p>K</p><p>I</p><p>I</p><p>I</p><p>I</p><p>X</p><p>BACB30EL()C()</p><p>BACB30EL()CN()</p><p>BACB30VF()K()</p><p>BACB30NU()K()</p><p>BACB30EL()CN() ALLOY STEEL,</p><p>DIFFUSED-NICKEL</p><p>CADMIUM PLATED,</p><p>HI-TORQUE,</p><p>SHORT THREAD,</p><p>REDUCED HEAD,</p><p>95 KSI SHEAR,</p><p>MAX TEMP</p><p>600 ˚F (316˚C)</p><p>BACB30NU()K()</p><p>NAS8703 THRU NAS8712</p><p>BACB30VF()K()</p><p>BACB30EL()-() ALLOY STEEL,</p><p>CADMIUM PLATED,</p><p>HI-TORQUE</p><p>RECESS, 100 ˚</p><p>REDUCED HEAD,</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>NAS8703 THRU NAS8712</p><p>BACB30LU()D()</p><p>BACB30LR()D()</p><p>ALLOY STEEL,</p><p>CADMIUM PLATED,</p><p>HI-TORQUE</p><p>RECESS,</p><p>SELF-LOCKING,</p><p>100 ˚ HEAD,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30FA()-()P BACB30FA()R()P</p><p>BACB30AB-P()-()A BACB30LH()-()</p><p>BACB30LP()-()</p><p>BACB30LR()-()</p><p>BACB30LU()-()</p><p>BACB30MS()K()</p><p>BACB30NN()K()</p><p>BACB30LH()D()ALLOY STEEL</p><p>100 ˚ CLOSE</p><p>TOLERANCE 160</p><p>KSI PHILLIPS</p><p>RECESS, SHORT</p><p>THREAD,</p><p>DRILLED,</p><p>CADMIUM PLATED,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30AB-P()-()</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>TABLE VII</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>MATING</p><p>PART</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION EQUIVALENT ALTERNATIVE</p><p>ALLOY STEEL</p><p>100 ˚ CLOSE</p><p>TOLERANCE 160</p><p>KSI PHILLIPS</p><p>RECESS, SHORT</p><p>THREAD,</p><p>UNDRILLED,</p><p>CADMIUM PLATED,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>N97161 S0006585385_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 49 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 70</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>ML</p><p>NO ALTERNATIVE</p><p>BACS12GM3-()</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>BACB30LH()U() BACB30LP()U()</p><p>BACB30LR()U()</p><p>PASSIVATED,</p><p>CROSS RECESS,</p><p>95 KSI SHEAR,</p><p>100 ˚ HEAD,</p><p>SHORT THREAD,</p><p>A286 CRES,</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>A286 CRES,</p><p>95 KSI SHEAR,</p><p>SHORT THREAD,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>CADMIUM</p><p>PLATED,</p><p>BACB30LH()-() BACB30LP()-()</p><p>BACB30LR()-()</p><p>BACB30LU()-()</p><p>BACB30MS()K()</p><p>BACB30NN()K()</p><p>A L</p><p>I</p><p>I</p><p>BACS12GP3L()</p><p>BACS12GR3L()</p><p>A</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>SCREW, 6AL-4V</p><p>TITANIUM,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>FULL THREADED,</p><p>POINTED,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>BACS12GP3K()</p><p>ALLOY STEELBACB30FB()-()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>TENSION</p><p>160 KSI</p><p>LONG THREAD,</p><p>REDUCED HEAD</p><p>RECESS, 100 ˚</p><p>HI-TORQUE</p><p>CADMIUM PLATED,</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>TABLE VII</p><p>INITIAL</p><p>FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97162 S0006585386_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 50 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 71</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>N</p><p>N</p><p>I N</p><p>N</p><p>BACB30LR()-()</p><p>BACB30LU()-()</p><p>BACB30NN()K()</p><p>A L</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30LP()U() BACB30LR()U()</p><p>PASSIVATED,</p><p>HI-TORQUE</p><p>RECESS,</p><p>100 ˚ HEAD,</p><p>LONG THREAD,</p><p>160 KSI</p><p>TENSION,</p><p>A286 CRES,</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>TABLE VII</p><p>BACB30LP()-() A286 CRES, CAD</p><p>LONG THREAD,</p><p>RECESS,</p><p>100 ˚ HEAD,</p><p>160 KSI</p><p>TENSION,</p><p>HI-TORQUE</p><p>CADMIUM</p><p>PLATED,</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>A286 CRES, BACB30UW()-()BACB30LL()U()</p><p>REDUCED HEAD,</p><p>RECESS, 100 ˚</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>PASSIVATED,</p><p>DOVETAIL</p><p>BACB30LL()-()</p><p>BACB30EL()CN()</p><p>BACB30EL()-()A286 CRES, A</p><p>A L</p><p>L</p><p>CADMIUM</p><p>BACB30VF()K()</p><p>BACB30UW()P()</p><p>BACB30UW()K()</p><p>I</p><p>I</p><p>SHORT THREAD,</p><p>HEAD,</p><p>95 KSI SHEAR,</p><p>BACB30NU()K() I</p><p>100 ˚ REDUCED</p><p>PLATED,</p><p>DOVETAIL</p><p>RECESS,</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97163 S0006585387_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 51 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 72</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>ML</p><p>I</p><p>A</p><p>V</p><p>M</p><p>M</p><p>M</p><p>A L</p><p>I</p><p>X</p><p>BACB30NN()K()</p><p>BACB30LR()-()</p><p>BACB30LP()-()</p><p>OR</p><p>MS14144</p><p>OR</p><p>BACN11N()</p><p>BACN10JD()</p><p>BACB30LU()-()</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>TABLE VII</p><p>ALLOY STEEL,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>LONG THREAD,</p><p>95 KSI SHEAR,</p><p>CLOSE</p><p>TOLERANCE,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30LR()DK()</p><p>BACB30LR()K() BACB30LP()-()A286 CRES,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>LONG THREAD,</p><p>CLOSE</p><p>TOLERANCE,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING, 160</p><p>KSI TENSION,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACB30LR()U()</p><p>BACB30LR()D()</p><p>BACB30NN()K()</p><p>BACB30MS()K()</p><p>BACB30LU()-()</p><p>BACB30LR()-()</p><p>BACB30LP()U()A286 CRES,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>LONG THREAD,</p><p>CLOSE TOLERANCE,</p><p>PASSIVATED,</p><p>160 KSI</p><p>TENSION,</p><p>MAX TEMP</p><p>900 ˚F (482˚C)</p><p>BACB30LR()-()</p><p>BACB30LU()-()</p><p>BACB30NN()K()</p><p>BACB30LP()-()A286 CRES,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>LONG THREAD,</p><p>CLOSE TOLERANCE,</p><p>CADMIUM PLATED,</p><p>160 KSI TENSION,</p><p>MAX TEMP 450 ˚F</p><p>(232˚C)</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>MATING</p><p>PART</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION EQUIVALENT ALTERNATIVE</p><p>N97164 S0006585388_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 52 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 73</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>H</p><p>IH</p><p>I</p><p>I</p><p>I</p><p>YI</p><p>Y</p><p>I</p><p>BACB30NN()K()</p><p>BACB30MS()K()</p><p>BACB30WP()K()R</p><p>BACB30NN()K()</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>TABLE VII</p><p>BACB30NN()K() BACB30MS()K()6AL-4V</p><p>TITANIUM,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>LONG THREAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>160 KSI</p><p>TENSION,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACB30WP()K()R</p><p>BACB30NN()C() 6AL-4V</p><p>TITANIUM,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>LONG THREAD,</p><p>CADMIUM PLATED,</p><p>160 KSI TENSION,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30MS()K()</p><p>BACB30MS()K() 6AL-4V</p><p>TITANIUM,</p><p>100 ˚ HEAD,</p><p>DOVETAIL</p><p>RECESS,</p><p>LONG THREAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>160 KSI</p><p>TENSION, MAX</p><p>TEMP 350 ˚F</p><p>(177˚C)</p><p>6AL-4V TITANIUM,</p><p>100 ˚ HEAD,</p><p>DOVETAIL RECESS,</p><p>LONG THREAD,</p><p>CADMIUM PLATED,</p><p>160 KSI TENSION,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACB30MS()C()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>MATING</p><p>PART</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION EQUIVALENT ALTERNATIVE</p><p>BACB30WP()K()R</p><p>BACB30NN()K()</p><p>BACB30WP()K()R</p><p>N97165 S0006585389_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 53 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 74</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>E C</p><p>CE</p><p>I</p><p>IH</p><p>I</p><p>I</p><p>BACB30VF()R()</p><p>BACB30VF()K()</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>TABLE VII</p><p>BACB30SW()-()</p><p>BACB30NU()K()BACB30NU()R() 6AL-4V</p><p>TITANIUM, 100 ˚</p><p>REDUCED HEAD,</p><p>DOVETAIL RECESS,</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>PHOSPHATE</p><p>FLUORIDE COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>BACB30SW()K() H-11 STEEL,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>100 ˚ HEAD,</p><p>HI-TORQUE,</p><p>125 KSI SHEAR,</p><p>LONG THREAD</p><p>H-11 STEEL,</p><p>DIFFUSED</p><p>NICKEL</p><p>CADMIUM</p><p>PLATED,</p><p>100 DEGREE</p><p>HEAD,</p><p>HI-TORQUE,</p><p>125 KSI SHEAR,</p><p>LONG THREAD</p><p>BACB30NU()K()</p><p>BACB30VF()K()</p><p>6AL-4V</p><p>TITANIUM, 100 ˚</p><p>REDUCED HEAD,</p><p>DOVETAIL RECESS,</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING, MAX</p><p>TEMP 350 ˚F</p><p>(177˚C)</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>MATING</p><p>PART</p><p>MATING PARTPART NUMBER DESCRIPTION EQUIVALENT ALTERNATIVE</p><p>BACB30VF()K()</p><p>BACB30NU()K()BACB30NU()C() 6AL-4V</p><p>TITANIUM, 100 ˚</p><p>REDUCED HEAD,</p><p>DOVETAIL RECESS,</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>CADMIUM PLATED,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>N97166 S0006585390_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 54 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 75</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>TABLE VII</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>ALTERNATIVE</p><p>INITIAL FASTENER OR SPECIFIED</p><p>PART NUMBER</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT</p><p>PART</p><p>I</p><p>BACB30NN3K() I</p><p>BACB30LU3-() LA</p><p>BACB30LP3-()</p><p>BACB30LH3-()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30VF()R()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30UR()R()</p><p>THREAD, OFFSET</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR</p><p>CRUCIFORM</p><p>HEAD, SHORT</p><p>100 ˚ REDUCED</p><p>LUBRICATED,</p><p>COATED,</p><p>TITANIUM,</p><p>FLOURIDE</p><p>PHOSPHATE</p><p>6AL-4V BACB30VF()K()</p><p>95 KSI SHEAR</p><p>CRUCIFORM</p><p>THREAD, OFFSET</p><p>HEAD, SHORT</p><p>100 ˚ REDUCED</p><p>BACB30VF()K()6AL-4V</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TITANIUM,</p><p>BACB30UR()K()</p><p>100 ˚ REDUCED</p><p>ALLOY 718,</p><p>HEAD,</p><p>CADMIUM</p><p>RECESS,</p><p>DOVETAIL</p><p>125 KSI SHEAR,</p><p>SHORT THREAD,</p><p>PLATED,</p><p>IBACB30UW()K()NICKELBACB30UW()P()</p><p>BACB30TP3-()</p><p>POINTED,</p><p>100 ˚ HEAD,</p><p>CROSS RECESS,</p><p>PLATED,</p><p>CADMIUM</p><p>ALLOY STEEL, NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97167 S0006585391_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 55 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 76</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>NO ALTERNATIVENAS1805-()L6AL-4VBACB30XM()K()</p><p>LONG THREAD,</p><p>CROSS RECESS,</p><p>TITANIUM,</p><p>150 KSI</p><p>TENSILE,</p><p>100 ˚ HEAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>NO ALTERNATIVE</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30VF()K() I</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>SHEAR,</p><p>BACB30VF()R() 6AL-4V</p><p>FLUORIDE</p><p>IBACB30WP()K()RBACB30WP()P()R NICKEL</p><p>DOVETAIL</p><p>PLATED,</p><p>LONG THREAD,</p><p>125 KSI SHEAR,</p><p>CADMIUM</p><p>RECESS,</p><p>100 ˚ HEAD,</p><p>ALLOY 718,</p><p>LUBRICATED</p><p>CETYL, ALCOHOL</p><p>COATED,</p><p>PHOSPHATE</p><p>THREAD,</p><p>SHEAR, SHORT</p><p>RECESS, 95 KSI</p><p>HEAD, CROSS</p><p>100 ˚ REDUCED</p><p>TITANIUM,</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>TABLE VII</p><p>BACB30VF()K()</p><p>THREAD, 95 KSI</p><p>HEAD, SHORT</p><p>100 ˚ REDUCED</p><p>CROSS RECESS,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TITANIUM,</p><p>6AL-4V</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97168 S0006585392_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 56 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 77</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>I</p><p>A L</p><p>A L</p><p>IB</p><p>IB</p><p>I</p><p>B I</p><p>L</p><p>B</p><p>B</p><p>B</p><p>A L</p><p>I</p><p>B</p><p>B</p><p>LA</p><p>I</p><p>I</p><p>I</p><p>ALTERNATIVEEQUIVALENTDESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PART</p><p>MATING</p><p>PART</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>ALLOY STEEL,</p><p>DIFFUSED</p><p>NICKEL-CADMIUM</p><p>PLATED, DOVETAIL</p><p>RECESS, CLOSE</p><p>TOLERANCE, PAN</p><p>HEAD, SHORT</p><p>THREAD, 160 KSI</p><p>TENSION, MAX</p><p>TEMP</p><p>600 ˚F (316˚C)</p><p>BACB30EM-P()L()BACB30EM-P()-()</p><p>BACB30NT()K()</p><p>ALLOY STEEL,</p><p>DIFFUSED</p><p>NICKEL-CADMIUM</p><p>PLATED, DOVETAIL</p><p>RECESS, CLOSE</p><p>TOLERANCE, PAN</p><p>HEAD, LONG</p><p>THREAD, 160 KSI</p><p>TENSION,</p><p>MAX TEMP</p><p>600 ˚F (316˚C)</p><p>BACB30EM-P()L()</p><p>A286 CRES,</p><p>CADMIUM</p><p>PLATED, CROSS</p><p>RECESS,</p><p>PAN HEAD,</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>NAS6703 THRU NAS6720</p><p>BACB30LK()-()</p><p>BOLT - RECESS DRIVE - PROTRUDING HEAD</p><p>TABLE VIII</p><p>BACB30LK()-()</p><p>NAS623-()-()</p><p>BACB30LE()K()</p><p>BACB30LM()-()</p><p>BACB30MR()K()</p><p>BACB30NM()K()</p><p>BACB30US()K()</p><p>NAS6603 THRU</p><p>NAS6620</p><p>NAS6703 THRU NAS6720</p><p>BACB30LE()-()</p><p>BACB30LE()K()</p><p>BACB30LJ()-()</p><p>BACB30LM()-()</p><p>BACB30LT()-()</p><p>BACB30MR()K()</p><p>BACB30NE()-()</p><p>BACB30NM()K()</p><p>BACB30US()K()</p><p>BACB30US()P()</p><p>NAS6620</p><p>NAS6603 THRU</p><p>N97169 S0006585393_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 57 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 78</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>H IB</p><p>I</p><p>I</p><p>I</p><p>I</p><p>IB</p><p>PART</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PART</p><p>MATING</p><p>INITIAL FASTENER OR SPECIFIED</p><p>BACB30LK()U()</p><p>BBACB30US()-()</p><p>PASSIVATED,</p><p>CROSS RECESS,</p><p>PAN HEAD,</p><p>SHORT THREAD,</p><p>95 KSI SHEAR,</p><p>A286 CRES,</p><p>NAS6703U THRU NAS6720U</p><p>MAX TEMP</p><p>900 ˚F (482˚C)</p><p>TITANIUM, CAD</p><p>PLATED,</p><p>PHILLIPS</p><p>RECESS SHORT</p><p>6AL-4VBACB30NT()C()</p><p>THREADED.</p><p>95 KSI</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30LJ()U()</p><p>BACB30LM()U()</p><p>BACB30LT()U()</p><p>BBACB30LE()U()</p><p>SHORT THREAD</p><p>PAN HEAD,</p><p>CROSS RECESS,</p><p>95 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>TITANIUM,</p><p>6AL-4V</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACB30NT()K()</p><p>BACB30LE()K()</p><p>BACB30LK()-()</p><p>BACB30MR()K()</p><p>BACB30NJ()K()</p><p>BBACB30LE()K()</p><p>MBACB30LE()-() B</p><p>M</p><p>M</p><p>M</p><p>BACB30LM()-()</p><p>BACB30LK()-()</p><p>BACB30LJ()-()</p><p>MBACB30LT()-()</p><p>BACB30MR()K() B</p><p>LABACB30NF()-() M</p><p>BACB30NE()-() LA M</p><p>BACB30NR()K()</p><p>BACB30NM()K()</p><p>BBACB30US()K()</p><p>B MBACB30US()P()</p><p>L MANAS6620</p><p>NAS6603 THRU</p><p>M</p><p>NAS6703 THRU</p><p>NAS6720</p><p>TABLE VIII</p><p>BOLT - RECESS DRIVE - PROTRUDING HEAD</p><p>BACB30NM()K()</p><p>BACB30NR()K()</p><p>BACB30NT()K()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97170 S0006585394_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 58 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 79</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>LNAS623-()-()</p><p>BACB30NT()T()</p><p>BACB30NR()K()</p><p>BACB30NM()K()</p><p>BACB30MR()K()</p><p>BACB30LT()-()</p><p>BACB30LJ()-()</p><p>BACB30LM()-()</p><p>BACB30LK()-()</p><p>BACB30LE()K()</p><p>BACB30LE()-() B</p><p>I</p><p>I</p><p>I</p><p>B</p><p>B</p><p>BOLT - RECESS DRIVE - PROTRUDING HEAD</p><p>TABLE VIII</p><p>I</p><p>I</p><p>IBACB30NM()K()</p><p>BACB30NR()K()</p><p>BACB30NT()K()</p><p>BACB30MR()K() B</p><p>BACB30LT()-()</p><p>BACB30LJ()-()</p><p>BACB30LM()-()</p><p>BACB30LK()-()</p><p>BBACB30LE()-()</p><p>BACB30LE()K() IB</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>NAS623-()-()W SCREW,</p><p>PLATED,</p><p>CADMIUM</p><p>PHILLIPS</p><p>RECESS,</p><p>PAN HEAD,</p><p>95 KSI SHEAR,</p><p>SHORT THREAD,</p><p>ALLOY STEEL,</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>ALLOY STEEL,</p><p>SCREW,</p><p>95 KSI SHEAR,</p><p>SHORT THREAD,</p><p>PHILLIPS</p><p>RECESS,</p><p>PAN HEAD,</p><p>CADMIUM</p><p>PLATED,</p><p>NAS623-()-()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>I</p><p>I</p><p>I</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97171 S0006585395_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 59 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 80</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>P</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30VL()-()</p><p>BACB30VL()-()D</p><p>BACB30VL()C()D</p><p>BACB30UY()-() 6AL-4V</p><p>TITANIUM,</p><p>PHOSPHATE</p><p>FLUORIDE</p><p>COATED</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30LB()-()</p><p>BOLT - BLIND - PROTRUDING HEAD</p><p>TABLE IX</p><p>MS90354-()()ALLOY STEEL</p><p>PLATED,</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK,</p><p>PULL TYPE,</p><p>SLEEVE,</p><p>CADMIUM</p><p>BACB30LB()C()CD A286 CRES</p><p>PLATED,</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK,</p><p>PULL TYPE,</p><p>SLEEVE,</p><p>CADMIUM</p><p>MS21141-()()P</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>SLEEVE,</p><p>PASSIVATED,</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>TYPE,</p><p>A286 CRES MS21141-()()BACB30LB()C()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97172 S0006585396_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 60 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 81</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BOLT - BLIND - PROTRUDING HEAD</p><p>TABLE IX</p><p>PLATED,</p><p>POSITIVE</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>TYPE,</p><p>CADMIUM</p><p>MS90354-()() BACB30LB()-()ALLOY STEEL</p><p>SLEEVE,</p><p>POSITIVE</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>TYPE,</p><p>CADMIUM PLATED,</p><p>BACB30LB()C()CDA286 CRES</p><p>SLEEVE,</p><p>MS21141-()()P</p><p>1200˚F (649˚C)</p><p>MAX TEMP</p><p>LOW PROFILE</p><p>HEAD, SHEAR,</p><p>LIGHTWEIGHT,</p><p>304 CRES</p><p>SLEEVE,</p><p>TITANIUM ALLOY</p><p>NUT</p><p>LOW PROFILE</p><p>HEAD, SHEAR,</p><p>LIGHTWEIGHT,</p><p>304 CRES</p><p>SLEEVE,</p><p>BAC30VL()-()</p><p>BACB30VL()-()D</p><p>BACB30VL()-()D</p><p>BACB30VL()-()</p><p>BACB30VL()C()D</p><p>BACB30VL()C()D</p><p>P</p><p>LOW PROFILE</p><p>HEAD, SHEAR,</p><p>LIGHTWEIGHT,</p><p>304 CRES</p><p>A-286 SS NUT,</p><p>DISPOSABLE</p><p>SLEEVE,</p><p>DRIVE NUT</p><p>A286 CRES</p><p>SLEEVE,</p><p>PASSIVATED,</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>TYPE, MAX</p><p>BACB30VL()-()</p><p>BACB30VL()-()D</p><p>BACB30LB()C()</p><p>PBACB30VL()C()D</p><p>MS21141-()()</p><p>ALLOY NUT,</p><p>DISPOSABLE</p><p>DRIVE NUT</p><p>TITANIUM</p><p>FASTENER SUBSTITUTION</p><p>ALTERNATIVE</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PARTPART NUMBER DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT</p><p>PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97173 S0006585397_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 61 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 82</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BOLT - BLIND - FLUSH HEAD</p><p>TABLE X</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>P</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30UZ()-()</p><p>BACB30VK()-()</p><p>6AL-4V</p><p>TITANIUM,</p><p>PHOSPHATE</p><p>FLUORIDE</p><p>BACB30VK()-()D</p><p>BACB30VK()C()D</p><p>BACB30VK()-()</p><p>COATED,</p><p>130 ˚ HEAD</p><p>BACB30VK()-()D</p><p>BACB30VK()C()D</p><p>CRES SLEEVE,</p><p>SLEEVE,</p><p>PASSIVATED</p><p>TREATED,</p><p>FLUORIDE</p><p>PHOSPHATE</p><p>LIGHTWEIGHT,</p><p>REDUCED SHEAR,</p><p>130 ˚ HEAD,</p><p>TITANIUM NUT,</p><p>6AL-4V</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30LA()-() ALLOY STEEL MS90353-()()</p><p>100 ˚ HEAD,</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>TYPE,</p><p>PLATED,</p><p>SLEEVE,</p><p>CADMIUM</p><p>1200˚F (649˚C)</p><p>MAX TEMP</p><p>TYPE,</p><p>BACB30LA()C()CD A286 CRES</p><p>SLEEVE,</p><p>MS21140-()()P</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>TYPE,</p><p>100 ˚ HEAD,</p><p>CADMIUM</p><p>PLATED,</p><p>A286 CRES</p><p>SLEEVE,</p><p>PASSIVATED,</p><p>100 ˚ HEAD,</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>MS21140-()()BACB30LA()C()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING</p><p>MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>REPAIR FASTENER</p><p>EQUIVALENT ALTERNATIVE</p><p>PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97174 S0006585398_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 62 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 83</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>P</p><p>P</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>TYPE,</p><p>1200˚F (649˚C)</p><p>MAX TEMP</p><p>MS21140-()()P BACB30LA()C()CD</p><p>TYPE,</p><p>LOCK, PULL</p><p>MECHANICAL</p><p>POSITIVE</p><p>100 ˚ HEAD,</p><p>PLATED,</p><p>CADMIUM</p><p>SLEEVE,</p><p>A286 CRES</p><p>BOLT - BLIND - FLUSH HEAD</p><p>TABLE X</p><p>MS21140-()() BACB30LA()C()A286 CRES</p><p>LOCK, PULL</p><p>MECHANICAL</p><p>POSITIVE</p><p>100 ˚ HEAD,</p><p>PASSIVATED,</p><p>SLEEVE,</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>BACB30VK()-()BACB30VK()C()D</p><p>BACB30VK()-()D</p><p>130 ˚ HEAD,</p><p>DRIVE NUT,</p><p>DISPOSABLE</p><p>AND SLEEVE,</p><p>PASSIVATED NUT</p><p>LIGHTWEIGHT,</p><p>REDUCED SHEAR,</p><p>NUT,</p><p>A-286 CRES</p><p>CRES SLEEVE,</p><p>BACB30VK()-()D</p><p>BACB30VK()C()D</p><p>BACB30VK()-()</p><p>DRIVE NUT,</p><p>DISPOSABLE</p><p>SLEEVE,</p><p>PASSIVATED</p><p>TREATED,</p><p>FLUORIDE</p><p>PHOSPHATE</p><p>LIGHTWEIGHT,</p><p>REDUCED SHEAR,</p><p>130 ˚ HEAD,</p><p>CRES SLEEVE,</p><p>PART</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>DESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>MATING</p><p>INITIAL FASTENER OR SPECIFIED</p><p>PART NUMBER MATING PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97175 S0006585399_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 63 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 84</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title</p><p>page for details</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BOLT - BLIND - FLUSH HEAD</p><p>TABLE X</p><p>PART</p><p>ALTERNATIVEEQUIVALENT</p><p>REPAIR FASTENER</p><p>DESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>MATING</p><p>INITIAL FASTENER OR SPECIFIED</p><p>PART NUMBER MATING PART</p><p>ALLOY STEEL BACB30LA()-()</p><p>SLEEVE,</p><p>100 ˚ HEAD,</p><p>POSITIVE</p><p>MECHANICAL</p><p>LOCK, PULL</p><p>TYPE,</p><p>CADMIUM</p><p>PLATED,</p><p>MS90353-()() NO EQUIVALENT</p><p>N97176 S0006585400_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 64 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 85</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>H</p><p>A L M</p><p>A L</p><p>L</p><p>M</p><p>I</p><p>I</p><p>M</p><p>I</p><p>I</p><p>I</p><p>A L</p><p>I</p><p>A L M</p><p>I</p><p>M</p><p>M</p><p>BACB30PE()A()</p><p>6AL-4V</p><p>TITANIUM,</p><p>CADMIUM PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD, 95</p><p>KSI SHEAR, MAX</p><p>TEMP 450 ˚F</p><p>(232˚C)</p><p>BACB30MW()C()</p><p>BACB30PE()-()</p><p>BACB30PE()-()</p><p>BACB30PB()AK()</p><p>6AL-4V</p><p>TITANIUM, BMS</p><p>10-85 COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD, 95</p><p>KSI SHEAR, MAX</p><p>TEMP 350 ˚F</p><p>(177˚C)</p><p>BACB30MW()K()</p><p>BACB30PE()AK()</p><p>BACB30PE()-()</p><p>BACB30PE()A()</p><p>BACB30PE()A()</p><p>BACB30PE()AK()</p><p>BACB30PB()A()</p><p>A286 CRES,</p><p>CADMIUM PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD, 110</p><p>KSI SHEAR, MAX</p><p>TEMP 450 ˚F</p><p>(232˚C)</p><p>BACB30PE()A()</p><p>BACB30PB()AK()</p><p>BACB30PE()AK()</p><p>BACB30PB()AK()</p><p>BACB30PB()A()</p><p>BACB30BP()A()</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD, 108</p><p>KSI SHEAR, MAX</p><p>TEMP 450 ˚F</p><p>(232˚C)</p><p>ALLOY STEEL,</p><p>CADMIUM PLATED,</p><p>BACB30PB()-()</p><p>BACB30PE()AK()</p><p>BOLT - TAPER SHANK - PROTRUDING HEAD</p><p>TABLE XI</p><p>BACB30PB()-()</p><p>BACB30PB()AK()</p><p>BACB30PB()A()</p><p>BACB30PB()-()</p><p>BACB30MW()K()</p><p>A286 CRES, BMSBACB30PB()AK()</p><p>10-85 COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD,</p><p>110 KSI SHEAR,</p><p>MAX TEMP 350 ˚F</p><p>(177˚C)</p><p>BACB30PB()A()</p><p>BACB30PE()A()</p><p>BACB30PE()AK()</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>EQUIVALENT</p><p>PART</p><p>MATINGDESCRIPTION ALTERNATIVE</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>MATING PART</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97177 S0006585401_V3</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 65 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 86</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BOLT - TAPER SHANK - PROTRUDING HEAD</p><p>TABLE XI</p><p>I</p><p>M</p><p>I</p><p>BACB30PE()-()ALLOY STEEL,</p><p>BMS 10-85 COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>TENSION HEAD,</p><p>180 KSI TENSION,</p><p>MAX TEMP 600 ˚F</p><p>(316˚C)</p><p>BACB30PE()K()</p><p>ALLOY STEEL,</p><p>BMS 10-85 COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD, 108</p><p>KSI SHEAR MAX</p><p>TEMP 600 ˚ (316˚)</p><p>BACB30PB()K()</p><p>BACB30PE()AK()</p><p>BACB30PE()A()</p><p>BACB30PB()-()</p><p>BACB30PE()-()</p><p>BACB30PE()A()</p><p>BACB30PB()AK()</p><p>BACB30PE()AK()</p><p>A286 CRES, CAD</p><p>PLATED, CETYL</p><p>ALCOHOL</p><p>LUBRICATED,</p><p>TENSION HEAD,</p><p>200 KSI TENSION,</p><p>MAX TEMP 450 ˚F</p><p>(232˚C)</p><p>BACB30PE()A()</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>TENSION HEAD,</p><p>200 KSI TENSION,</p><p>MAX TEMP 350 ˚F</p><p>(177˚C)</p><p>10-85 COATED,</p><p>BACB30PE()AK()</p><p>BACB30PE()A()A286 CRES, BMSBACB30PE()AK()</p><p>BACB30PB()A()</p><p>ALLOY STEEL,BACB30PE()-()</p><p>CADMIUM PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>TENSION HEAD,</p><p>180 KSI TENSION,</p><p>MAX TEMP 450 ˚F</p><p>(232˚C)</p><p>BACB30PE()A()</p><p>BACB30PE()AK()</p><p>MATING PART</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>ALTERNATIVEDESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>K MZ</p><p>I</p><p>K M</p><p>K M</p><p>K M</p><p>K M</p><p>I</p><p>I</p><p>K M</p><p>Z NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97178 S0006585402_V3</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 66 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 87</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>H</p><p>A L</p><p>M</p><p>M</p><p>I</p><p>A L</p><p>BACB30KD()A()BACB30KD()-()</p><p>ALLOY STEEL,</p><p>CAD PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>TENSION HEAD,</p><p>180 KSI TENSION,</p><p>MAX TEMP 450˚F</p><p>(232˚C)</p><p>BACB30KD()A()</p><p>BACB30MU()C() 6AL-4V</p><p>TITANIUM, CAD</p><p>PLATED, CETYL</p><p>ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD,</p><p>95 KSI SHEAR,</p><p>MAX TEMP 450˚</p><p>(232˚C)</p><p>BACB30MU()K()</p><p>BACB30PD()A()</p><p>BACB30KD()A()</p><p>BACB30KD()-()</p><p>BACB30PD()A()BACB30PD()-()</p><p>NO ALTERNATIVE</p><p>NO ALTERNATIVE</p><p>BACB30MU()K()</p><p>BACB30KD()-()</p><p>BACB30KD()A()</p><p>BOLT - TAPER SHANK - FLUSH HEAD</p><p>TABLE XI</p><p>6AL-4V</p><p>TITANIUM, BMS,</p><p>10-85 COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD, 95</p><p>KSI SHEAR, MAX</p><p>TEMP 350˚ (177 C̊)</p><p>ALLOY STEEL,</p><p>CAD PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>SHEAR HEAD,</p><p>108 KSI SHEAR,</p><p>MAX TEMP 450˚F</p><p>(232˚C)</p><p>MATING PART</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>ALTERNATIVEDESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>A286 CRES, CAD</p><p>PLATED,CETYL</p><p>ALCOHOL</p><p>LUBRICATED,</p><p>TENSION HEAD,</p><p>200 KSI TENSION,</p><p>MAX TEMP 450˚F</p><p>(232 C̊)</p><p>A286 CRES, CAD</p><p>PLATED,CETYL</p><p>ALCOHOL</p><p>LUBRICATED, SHEAR</p><p>HEAD, 110 KSI</p><p>SHEAR, MAX TEMP</p><p>450˚F (232 C̊)</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97179 S0006585403_V3</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 67 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 88</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>A</p><p>B</p><p>C</p><p>I</p><p>J</p><p>D</p><p>E</p><p>G</p><p>H</p><p>F</p><p>REFER TO TABLE I FOR THE FASTENER</p><p>THE INSTALLATION OF FASTENERS.</p><p>THE SHEAR AND TENSION TYPE FASTENERS USE</p><p>DIFFERENT TORQUE VALUES AND INSTALLATION</p><p>NOTES</p><p>APPLY A FILLET SEAL TO THE WET SIDE OF THE</p><p>FASTENER INSIDE THE FUEL TANK. REFER TO</p><p>SLOPED SURFACE.</p><p>THIS FASTENER IS NOT PERMITTED IN AREAS</p><p>DO NOT INSTALL THIS COLLAR OR NUT ON A</p><p>INSTALLATION.</p><p>PROTECTIVE TREATMENT FOR FASTENER</p><p>REFER TO SRM 51-40-02 FOR THE REMOVAL AND</p><p>TOOLS. REFER TO SRM 51-40-04.</p><p>REFER TO SRM 51-20-01 FOR THE NECESSARY</p><p>SRM 51-20-05.</p><p>SUBSTITUTION INDEX.</p><p>-</p><p>____NOTE:</p><p>ALUMINUM STRUCTURE.</p><p>OF THE SURROUNDING STRUCTURE AND THE</p><p>ALL THESE FASTENERS, BOTH THE</p><p>INITIATION OF CORROSION OF ANY ADJACENT</p><p>SHOULD BE INSTALLED WET WITH THE</p><p>NECESSARY SEALANT MATERIAL.</p><p>RECOMMENDED AND THE ALTERNATIVES,</p><p>THIS MAY RESULT IN THE RUST-STREAKING</p><p>- GRAPHITE (CARBON FIBER) STRUCTURE</p><p>- CRES STRUCTURE</p><p>NECESSARY</p><p>-</p><p>STEEL (CRES) OR TITANIUM FASTENERS IN:</p><p>AREAS WHERE ANTI-MAGNETIC FASTENERS ARE</p><p>DO NOT USE ALLOY STEEL FASTENERS AS AN</p><p>ALTERNATIVE FOR THE CORROSION RESISTANT</p><p>WHERE THE TEMPERATURE IS MORE THAN 350 ˚F</p><p>(177˚C)</p><p>REFER TO BAC5117.</p><p>-</p><p>-</p><p>OR CADMIUM-PLATED A-286.</p><p>TORQUE-CONTROLLED TOOLING. REFER TO</p><p>SRM 51-40-04.</p><p>THIS FASTENER IS NOT PERMITTED IN AREAS</p><p>WHERE ELECTRICAL CONDUCTIVITY IS REQUIRED.</p><p>THIS FASTENER IS PERMITTED ONLY IN CLOSE</p><p>REAM OR LARGER HOLES (NON-INTERFERENCE).</p><p>THESE FASTENERS MUST BE INSTALLED WITH</p><p>COATING, MAY DISAPPEAR ALLOWING THE</p><p>ALLOY-STEEL FASTENER TO CORRODE.</p><p>STRUCTURE ARE TITANIUM WITH BMS 10-85</p><p>APPLIED, A-286 WITH BMS 10-85 APPLIED,</p><p>A STRUCTURALLY ACCEPTABLE ALTERNATIVE.</p><p>HOWEVER, IN A CORROSIVE ENVIRONMENT THE</p><p>CADMIUM PLATING, WHICH IS A SACRIFICIAL</p><p>CADMIUM-PLATED ALLOY-STEEL FASTENERS ARE</p><p>THE RECOMMENDED FASTENERS IN ALUMINUM</p><p>TITANIUM STRUCTURE</p><p>DO NOT USE CADMIUM PLATED FASTENERS AS AN</p><p>ALTERNATIVE FOR BARE OR ALUMINUM COATED</p><p>FASTENERS WHEN YOU INSTALL FASTENERS</p><p>THROUGH THE MATERIALS THAT FOLLOW:</p><p>-</p><p>- GRAPHITE (CARBON FIBER) STRUCTURE</p><p>USE A SELF-ALIGNING COLLAR BACC30CH() WHEN</p><p>THE COLLAR SIDE SLOPE IS MORE THAN 0.5</p><p>DEGREES.</p><p>DO NOT USE CADMIUM PLATED FASTENERS IN</p><p>TITANIUM OR GRAPHITE (CARBON FIBER)</p><p>STRUCTURE.</p><p>ALTERNATIVES</p><p>SPEAK TO THE BOEING COMPANY FOR FASTENER</p><p>N97180 S0006585404_V3</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 1 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 89</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>19 THROUGH 21</p><p>16 THROUGH 18</p><p>9 THROUGH 15</p><p>3 THROUGH 8</p><p>LOCKBOLT - FLUSH HEAD (TENSION)</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>LOCKBOLT - PROTRUDING HEAD (TENSION)</p><p>LOCKBOLT - PROTRUDING HEAD (SHEAR)</p><p>LOCKBOLT FASTENER SUBSTITUTION INDEX</p><p>TABLE I</p><p>TYPE OF LOCKBOLT FASTENER</p><p>V</p><p>IV</p><p>III</p><p>II</p><p>NUMBER</p><p>SHEET</p><p>NUMBER</p><p>TABLE</p><p>LOCATION OF FASTENER</p><p>N97181 S0006585405_V1</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 2 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 90</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>H</p><p>BACC30K()BACB30GW()-()</p><p>BACB30GW()A() BACC30K()</p><p>NAS1080C()</p><p>NAS1080C()</p><p>H</p><p>A B G</p><p>GB</p><p>B</p><p>A</p><p>A</p><p>BACN10XJ()</p><p>BACC30BL()</p><p>BACC30BQ() A</p><p>BACB30VT()K()</p><p>B G</p><p>BACN10YZ()</p><p>A</p><p>BACN10XJ()</p><p>A B G</p><p>BACB30FP()-()</p><p>BA</p><p>BACN10XJ()</p><p>B GA</p><p>BACN10XJ()</p><p>BA</p><p>A</p><p>BA</p><p>A</p><p>BACC30M()</p><p>BACC30AG() A</p><p>ABACC30AG()</p><p>BA</p><p>ABACC30AG()</p><p>C</p><p>C</p><p>C</p><p>C</p><p>BA</p><p>BA</p><p>G</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>PLATED,</p><p>CADMIUM</p><p>BACB30FM()-()</p><p>FLAT HEAD,</p><p>STUMP TYPE,</p><p>95 KSI SHEAR,</p><p>LUBRICATED</p><p>ALLOY STEEL,BACB30AR()-() BACC30K()</p><p>OR</p><p>NAS1080C()</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>BACN10XJ()</p><p>BACB30FM()A()</p><p>BACC30BK()BACB30VN()K()</p><p>NAS1080C()0.0156</p><p>ALLOY STEEL</p><p>CAD PLATED</p><p>OVERSIZE</p><p>PULL TYPE</p><p>GUN DRIVEN</p><p>BACB30CU()-()</p><p>BACB30MY()K()X</p><p>BACB30NX()K()X</p><p>TABLE II</p><p>LOCKBOLT - PROTRUDING HEAD (SHEAR)</p><p>BACC30K()</p><p>OR</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30M()</p><p>BACC30M()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97182 S0006585406_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 3 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 91</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>GBA</p><p>ABACC30BL()</p><p>BACC30BK()</p><p>BACB30VT()K()</p><p>BACB30VN()K()</p><p>BACN10YZ()</p><p>BACB30VN()K() C</p><p>BACB30VT()K() BACC30BL()C</p><p>BACC30BK()</p><p>BACC30BP()</p><p>GBA</p><p>A B</p><p>BACC30BQ()</p><p>C</p><p>A E</p><p>C</p><p>B G EA</p><p>A</p><p>BACN10YZ()</p><p>BACC30BQ()</p><p>B</p><p>BACC30BP() B</p><p>C.T. SHANK,</p><p>1.0 PINTAIL,</p><p>(PULL TYPE,</p><p>GUN DRIVEN),</p><p>CADMIUM PLATED</p><p>BACB30MY()K()</p><p>BACB30FM()A()</p><p>BACB30FM()-()ALLOY STEEL,BACB30GW()-()</p><p>BACB30GW()A() A-286 CRES,</p><p>C.T. SHANK,</p><p>1.0 PINTAIL,</p><p>(PULL TYPE,</p><p>GUN DRIVEN),</p><p>CADMIUM PLATED</p><p>B</p><p>BACC30K()</p><p>A</p><p>NAS1080E()</p><p>BACC30AG()</p><p>BA</p><p>BACB30FM()A()</p><p>C</p><p>BACC30AB()C</p><p>B E</p><p>BBACC30BP()</p><p>BACC30BL()</p><p>A</p><p>EBACC30BK()</p><p>E</p><p>C</p><p>C</p><p>BACB30VT()K()</p><p>BACB30VN()K()</p><p>BACC30K()</p><p>OR</p><p>NAS1080C()</p><p>BBACC30M() A</p><p>ABACC30AG()</p><p>BACC30AG() A</p><p>BACC30M() A B</p><p>BABACC30M()</p><p>ABACC30AG()</p><p>A</p><p>ABACC30BQ() E</p><p>BBACC30BS()</p><p>BACN10YZ()</p><p>H</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>MATING</p><p>PART</p><p>TABLE II</p><p>LOCKBOLT - PROTRUDING HEAD (SHEAR)</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97183 S0006585407_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 4 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 92</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACC30AB()SBACB30FM()A()UBACC30L()</p><p>BACC30AB()SBACB30MB()A()U</p><p>BACB30FM()-()</p><p>BACB30FM()A()</p><p>BACB30MY()K()</p><p>NAS1080E</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACB30VN()K() BACC30BK()</p><p>BACC30BQ()</p><p>BACC30BP()</p><p>BACC30BL()BACB30VT()K()</p><p>BACN10YZ()</p><p>C</p><p>A</p><p>B</p><p>BA</p><p>C</p><p>A B G</p><p>PASSIVATED,</p><p>95 KSI SHEAR,</p><p>LUBRICATED,</p><p>PULLTYPE,</p><p>A286 CRES,</p><p>MAX TEMP</p><p>900 ˚F (482˚C)</p><p>A B</p><p>ALLOY STEEL</p><p>CAD PLATED</p><p>LUBRICATED</p><p>95 KSI SHEAR</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>A B</p><p>H I</p><p>C</p><p>DIFFUSED</p><p>SHEAR,</p><p>LUBRICATED,</p><p>PULL TYPE,</p><p>PLATED, 95 KSI</p><p>NICKEL-CADMIUM</p><p>ALLOY STEEL, J</p><p>MAX TEMP</p><p>600 ˚F (316˚C)</p><p>BA</p><p>A</p><p>BA</p><p>A</p><p>BA</p><p>A</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACB30GW()A()U</p><p>BACB30GW()D()</p><p>BACB30GW()D()N</p><p>TABLE II</p><p>LOCKBOLT - PROTRUDING HEAD (SHEAR)</p><p>NAS1080C()</p><p>BACC30K()</p><p>OR</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97184 S0006585408_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 5 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 93</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>IHF</p><p>IHF</p><p>6AL-4V</p><p>LUBRICATED,</p><p>95 KSI SHEAR,</p><p>PULL TYPE,</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>TITANIUM,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>6AL-4V</p><p>TITANIUM,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>STUMP TYPE,</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>BACB30UD()K()</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACB30TZ()K()</p><p>TABLE II</p><p>LOCKBOLT - PROTRUDING HEAD (SHEAR)</p><p>BACC30BE BACB30FM()-()</p><p>BACN10XJ()</p><p>BACN10XJ()</p><p>A B G</p><p>BACB30FM()A()</p><p>BACC30BE()</p><p>BACC30K()</p><p>OR</p><p>BACN10XJ()</p><p>BACN10XJ()</p><p>BACB30FM()-()</p><p>BACB30FM()A()</p><p>B GA</p><p>BACC30M()</p><p>A BBACC30AG()</p><p>ABACC30AG()</p><p>BACC30M()</p><p>BACC30M() A B</p><p>ABACC30AG()</p><p>ABACC30M() B</p><p>ABACC30AG()</p><p>A B G</p><p>F</p><p>F</p><p>BACB30VN()K() BACC30BK()</p><p>BACC30BL()BACB30VT()K()</p><p>BACN10YZ()</p><p>ABACC30BQ()</p><p>BBACC30BP()</p><p>A B G</p><p>BACB30MY()K()</p><p>BACN10XJ()</p><p>BACC30M() A</p><p>BACC30AG() A</p><p>A B G</p><p>B GA</p><p>B GA</p><p>BACN10YZ()</p><p>BACB30VT()K()</p><p>BACC30BK()BACB30VN()K()</p><p>BACN10XJ()</p><p>BACB30MY()K()</p><p>B</p><p>BACC30BQ() A</p><p>A</p><p>BACC30BL()</p><p>BBACC30BP()</p><p>ABACC30AG()</p><p>BACC30M() BA</p><p>A B G</p><p>A B</p><p>A B</p><p>A B</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97185 S0006585409_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 6 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 94</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACN10XJ()</p><p>H I</p><p>GBA</p><p>BACN10XJ()</p><p>BACB30FM()-()</p><p>BACB30FM()A()</p><p>ABACC30M() B</p><p>ABACC30AG()</p><p>BACC30M() A B</p><p>ABACC30AG()</p><p>F</p><p>F</p><p>BACN10XJ()</p><p>BACB30MY()K() BACC30AG() A</p><p>ABACC30M() B</p><p>A GB</p><p>A</p><p>B</p><p>B</p><p>A</p><p>B</p><p>GA</p><p>BACB30VT()K()</p><p>BACC30BQ()</p><p>BACC30BP()</p><p>BACN10YZ()</p><p>BACC30BL()</p><p>BACC30BK()6AL-4V</p><p>TITANIUM,</p><p>95 KSI SHEAR,</p><p>LIGHTWEIGHT,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>GBA</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACB30VN()K()</p><p>TABLE II</p><p>LOCKBOLT - PROTRUDING HEAD (SHEAR)</p><p>NO EQUIVALENT</p><p>N97186 S0006585410_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 7 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 95</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>A GB</p><p>BACB30FM()A()</p><p>BACB30FM()-()</p><p>BACN10XJ()</p><p>BACN10XJ()</p><p>ABACC30M() B</p><p>BACC30AG() A</p><p>BACC30M() A B</p><p>BACC30AG() A</p><p>H IF</p><p>GBA</p><p>F</p><p>BACN10XJ()</p><p>BACB30MY()K()</p><p>ABACC30M() B</p><p>ABACC30AG()</p><p>A GB</p><p>BACN10YZ()</p><p>A</p><p>BACC30BQ()</p><p>GB</p><p>A</p><p>BACC30BL()BACB30VT()K()</p><p>BA</p><p>BACC3OBP() B</p><p>BACC30BK()BACB30VN()K()</p><p>BACB30XH()K()BACC30BN()L6AL-4V</p><p>TITANIUM,</p><p>95 KSI SHEAR,</p><p>AL COATED, CETYL</p><p>ALCOHOL</p><p>LUBRICATED,</p><p>WITH SEALANT</p><p>ESCAPE GROOVE,</p><p>FOR USE IN</p><p>COMPOSITES, MAX</p><p>TEMP 250 ˚F</p><p>BACB30XC()HK() BACC30CG()</p><p>BACB30XH()K()BACC30BN()L6AL-4V</p><p>TITANIUM,</p><p>95 KSI SHEAR, AL</p><p>COATED, CETYL</p><p>ALCOHOL</p><p>LUBRICATED,</p><p>FOR USE IN</p><p>COMPOSITES, MAX</p><p>TEMP 250 ˚F</p><p>BACB30XC()K() BACC30CG()</p><p>BACB30NX()K() BACC30AB()S</p><p>BACB30NX()K() BACC30AB()S</p><p>BACC30BK()</p><p>STUMP TYPE,</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>LIGHTWEIGHT,</p><p>95 KSI SHEAR,</p><p>TITANIUM,</p><p>6AL-4V</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTIONPART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>LOCKBOLT - PROTRUDING HEAD (SHEAR)</p><p>TABLE II</p><p>D</p><p>D</p><p>B</p><p>B</p><p>BACB30VR()K() NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97187 S0006585411_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 8 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 96</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>A GB</p><p>A EB</p><p>A EB G</p><p>100 ˚ HEAD,</p><p>C.T. SHANK,</p><p>1.0 PINTAIL,</p><p>(PULL TYPE,</p><p>GUN DRIVEN),</p><p>CADMIUM</p><p>PLATED, CETYL</p><p>ALCOHOL</p><p>LUBRICATED</p><p>ALLOY STEEL,</p><p>STEEL</p><p>NAS1080E</p><p>BACC30K()</p><p>NAS1080C()</p><p>OR</p><p>BACN10YZ()</p><p>BACC30BL()</p><p>A</p><p>BBACC30BP()</p><p>BACC30BQ()</p><p>DC</p><p>BACC30BS()</p><p>BACB30VU()K()</p><p>E</p><p>E</p><p>A B</p><p>BACC30BK()CBACB30XT()K() D</p><p>BACC30BK()CBACB30XT()K() D</p><p>E</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACB30GY()-()</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>BACC30BL()BACB30VU()K()</p><p>BACN10YZ()</p><p>BACC30BQ()</p><p>BACC30BP()</p><p>DC</p><p>A</p><p>A B</p><p>B</p><p>NAS1080D()BACB30GS()-() 7075-T6 AL</p><p>STUMP TYPE</p><p>100 ˚ HEAD</p><p>HAMMER DRIVEN</p><p>NAS1535 THRU 1542 NAS1080K()</p><p>PULL TYPE</p><p>100 ˚ HEAD</p><p>GUN DRIVEN</p><p>NAS1080D() NAS1535 THRU 1542 NAS1080K()BACB30GQ()-() 7075-T6 AL</p><p>STEEL, CAD</p><p>PLATED, 0.0156</p><p>OVERSIZE</p><p>PULL TYPE</p><p>GUN DRIVEN</p><p>NAS1080D()ALLOYBACB30CT()-()</p><p>BACC30M() A B</p><p>BACC30M() A BBACB30NW()K()X C</p><p>BACB30FQ()-()</p><p>BACC30M() A B</p><p>BACC30M() A B</p><p>BACB30FQ()A()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97188 S0006585412_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 9 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 97</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>A GB</p><p>A EB G</p><p>A EB</p><p>BACC30BL()</p><p>BACC30BK()BACB30XT()K()</p><p>BACB30VU()K()</p><p>EBACC30BP()</p><p>BACC30BS() B</p><p>BACN10YZ()</p><p>B</p><p>NAS1080E</p><p>STEEL</p><p>CADMIUM</p><p>PLATED,</p><p>CETYL</p><p>ALCOHOL</p><p>100 ˚ HEAD,</p><p>C.T. SHANK,</p><p>(PULL TYPE,</p><p>A-286 CRES,</p><p>1.0 PINTAIL,</p><p>GUN DRIVEN),</p><p>LUBRICATED</p><p>EA</p><p>B</p><p>A</p><p>BACC30BQ()</p><p>DC</p><p>DC</p><p>BACN10YZ()</p><p>B</p><p>A</p><p>ADCBACC30K()</p><p>NAS1080C()</p><p>OR</p><p>BACC30BK()BACB30XT()K() DC E</p><p>900 ˚F (482˚C)</p><p>BACB30FN()A()UA286 CRES,</p><p>MAX TEMP</p><p>PULL TYPE,</p><p>100 ˚ HEAD,</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>PASSIVATED,</p><p>BACC30L()BACB30GY()A()U</p><p>A B</p><p>600 ˚F (316˚C)</p><p>JBACB30GY()D()N NAS1080E</p><p>NICKEL-CADMIUM</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>ALLOY STEEL,</p><p>MAX TEMP</p><p>PULL TYPE,</p><p>LUBRICATED,</p><p>95 KSI SHEAR,</p><p>PLATED,</p><p>BACC30AB()S</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACB30GY()A() BACC30BL()BACB30VU()K()</p><p>BACC30BQ()</p><p>BACC30BP()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97189 S0006585413_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 10 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BA G</p><p>BA G</p><p>NAS1080K()</p><p>TITANIUM,</p><p>100 ˚ REDUCED</p><p>HEAD, STUMP</p><p>TYPE, 95 KSI</p><p>SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>6AL-4V B</p><p>A</p><p>A</p><p>B</p><p>B</p><p>A</p><p>BACN10XJ()</p><p>TITANIUM,</p><p>100 ˚ REDUCED</p><p>HEAD, STUMP</p><p>TYPE,</p><p>CHAMFERED</p><p>STUMP END,</p><p>95 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>BACC30BE()6AL-4V</p><p>A B</p><p>A</p><p>B</p><p>A B</p><p>BACB30XT()K() BACC30BK()</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACB30NW()K()BACB30UC()K() BACC30M()</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>BACB10YZ()</p><p>BACC30BQ()</p><p>BACC30BL()</p><p>BACC30BP()BACB30VU()K()</p><p>BACB30NW()K()</p><p>BACB30VU()K()</p><p>BACC30AG()</p><p>ABACC30M()</p><p>BACC30BQ()</p><p>A</p><p>B</p><p>BACC30BL()</p><p>BACN10YZ()</p><p>B</p><p>A</p><p>BACC30BP() B</p><p>B</p><p>A G</p><p>250 ˚F (121˚C)</p><p>BACB30TY()K()</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TITANIUM,</p><p>MAX TEMP</p><p>PULL TYPE,</p><p>100 ˚ HEAD,</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>6AL-4V BACC30BE()</p><p>BA G</p><p>BACB30UC()K()A</p><p>BACC30BL()BACB30VU()K()</p><p>BACC30BP()</p><p>BACC30BQ()</p><p>BACN10YZ()</p><p>BACC30M()BACB30NW()K()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97190 S0006585414_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 11 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.1</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BA G</p><p>GB</p><p>B</p><p>A</p><p>A</p><p>BA</p><p>B</p><p>250 ˚F (121˚C)</p><p>6AL-4V</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>95 KSI SHEAR,</p><p>LIGHTWEIGHT,</p><p>STUMP TYPE,</p><p>100 ˚ HEAD,</p><p>TITANIUM,</p><p>BACC30BK() A</p><p>6AL-4V</p><p>95 KSI SHEAR,</p><p>LIGHTWEIGHT,</p><p>100 ˚ HEAD,</p><p>TITANIUM,</p><p>ALUMINUM</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>BACC30BK()</p><p>250 ˚F (121˚C)</p><p>A B</p><p>A B</p><p>A</p><p>B</p><p>250 ˚F (121˚C),</p><p>WITH SEALANT</p><p>ESCAPE GROOVE,</p><p>FOR USE IN</p><p>COMPOSITES</p><p>6AL-4V</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>95 KSI SHEAR,</p><p>LIGHTWEIGHT,</p><p>130 ˚ HEAD,</p><p>TITANIUM,</p><p>BACC30BN()L</p><p>BACB30XT()K() BACC30BK()</p><p>BACC30BQ()</p><p>BACN10YZ()</p><p>BACC30BP()</p><p>BACB30VU()K()</p><p>BACB30VM()K() BACC30BK()</p><p>BACC30BL()</p><p>TABLE III</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>BACB30VP()K() BACB30NW()K() BACC30M()</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACB30VM()K() BACB30NW()K() BACC30M()</p><p>BACC30BK()BACB30VM()K()</p><p>BACB30XT()K()</p><p>BACC30BL()BACB30VU()K()</p><p>BACN10YZ()</p><p>BACC30BP()</p><p>BACC30BQ()</p><p>BACC30BK()</p><p>BACB30WB()HK() NO ALTERNATIVE</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97191 S0006585415_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 12 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.2</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>FOR USE IN</p><p>COMPOSITES</p><p>ESCAPE GROOVE,</p><p>WITH SEALANT</p><p>LIGHTWEIGHT,</p><p>AL COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP 250 ˚F,</p><p>FOR USE IN</p><p>COMPOSITES</p><p>95 KSI SHEAR,</p><p>(MS24694) HEAD,</p><p>TITANIUM, 100 ˚</p><p>6AL-4V BACC30BN()L D</p><p>B</p><p>COMPOSITES</p><p>250 ˚F (121˚C),</p><p>FOR USE IN</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>95 KSI SHEAR,</p><p>LIGHTWEIGHT,</p><p>130 ˚ HEAD,</p><p>TITANIUM,</p><p>6AL-4V BACC30BN()L</p><p>250 ˚F (121˚C),</p><p>LIGHTWEIGHT,</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>95 KSI SHEAR,</p><p>(MS24694) HEAD,</p><p>TITANIUM, 100 ˚</p><p>6AL-4V BACC30BN()L B</p><p>D</p><p>TABLE III</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACB30WD()K() BACB30XF()K() BACC30CG()</p><p>BACB30NY()K() BACC30AB()S</p><p>BACB30XR()K()BACB30WB()K()</p><p>BACB30WD()HK() BACB30NY()K() BACC30AB()S</p><p>BACC30CG()NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97192 S0006585416_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 13 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.3</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BBACC30AB()SBACB30NZ()K()</p><p>FOR USE IN</p><p>COMPOSITES</p><p>ESCAPE GROOVE,</p><p>WITH SEALANT</p><p>FOR USE IN</p><p>COMPOSITES</p><p>ESCAPE GROOVE,</p><p>WITH SEALANT</p><p>250 ˚F (121˚C),</p><p>ALUMINUM</p><p>STUMP TYPE,</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>LIGHTWEIGHT,</p><p>95 KSI SHEAR,</p><p>(MS24694) HEAD,</p><p>TITANIUM, 100 ˚</p><p>6AL-4V BACC30BN()L</p><p>250 ˚F (121˚C),</p><p>BACC30BN()L</p><p>LIGHTWEIGHT,</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>PIGMENTED</p><p>COATING,</p><p>ALUMINUM</p><p>95 KSI SHEAR,</p><p>100 ˚ HEAD,</p><p>TITANIUM,</p><p>6AL-4V</p><p>TABLE III</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACB30WD()HK()BACB30WE()HK() BACC30BN()L</p><p>BACB30XB()HK()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97194 S0006585417_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 14 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.4</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>6AL-4V</p><p>100 ˚ HEAD,</p><p>LIGHTWEIGHT,</p><p>95 KSI SHEAR,</p><p>AL COATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP 250 ˚F</p><p>(121˚C), FOR</p><p>USE IN</p><p>COMPOSITES</p><p>TITANIUM,</p><p>B</p><p>DBACC30BN()</p><p>BACC30AB()S</p><p>BACC30CG()BACB30XG()K()BACB30XB()K()</p><p>BACB30NZ()K()</p><p>FOR USE IN</p><p>COMPOSITES</p><p>ESCAPE GROOVE,</p><p>WITH SEALANT</p><p>GBA</p><p>A</p><p>B</p><p>BA</p><p>95 KSI SHEAR,</p><p>STUMP TYPE,</p><p>MAX TEMP 250 ˚F</p><p>(121˚C),</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>PIGMENTED</p><p>COATING,</p><p>ALUMINUM</p><p>LIGHTWEIGHT,</p><p>100 ˚ HEAD,</p><p>TITANIUM,</p><p>BACC30BN()L6AL-4V</p><p>6AL-4V BACC30BK()</p><p>LUBRICATED,</p><p>MAX TEMP 250 ˚</p><p>(121˚C)</p><p>ALUMINUM</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>95 KSI SHEAR,</p><p>LIGHTWEIGHT,</p><p>100 ˚ HEAD,</p><p>TITANIUM,</p><p>BACN10YZ()</p><p>BACC30BQ</p><p>BACC30BP()</p><p>BACC30BL()</p><p>TABLE III</p><p>LOCKBOLT - FLUSH HEAD (SHEAR)</p><p>BACB30XB()HK() BACC30BN()L</p><p>BACB30YP()K()</p><p>BACB30YC()HK()</p><p>BACB30XT()K()</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97195 S0006585418_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 15 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.5</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>8740 ALLOY</p><p>STEEL,</p><p>C.T. SHANK,</p><p>1.0 PINTAIL,</p><p>(PULL TYPE,</p><p>GUN DRIVEN),</p><p>CADMIUM</p><p>PLATED</p><p>C.T. SHANK,</p><p>1.0 PINTAIL,</p><p>(PULL TYPE,</p><p>GUN DRIVEN),</p><p>CADMIUM</p><p>PLATED</p><p>A-286 CRES</p><p>A-286 CRES</p><p>C.T. SHANK,</p><p>1.0 PINTAIL,</p><p>(PULL TYPE,</p><p>GUN DRIVEN),</p><p>A</p><p>BACC30MB()A()U</p><p>PASSIVATED</p><p>PLATED,</p><p>160 KSI</p><p>TENSION,</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>BACC30Q()</p><p>ALLOY STEEL,</p><p>PULL TYPE,</p><p>AC</p><p>C</p><p>J</p><p>NICKEL-CADMIUM</p><p>NAS1080-()</p><p>OR</p><p>NAS1080P()</p><p>BA</p><p>BACB30GP()-()</p><p>NAS1525 THRU NAS1532</p><p>NAS108OD</p><p>SHANK, STUMP</p><p>TOLERANCE</p><p>CLOSE</p><p>7075-T6 AL,</p><p>MAX TEMP</p><p>PULL TYPE,</p><p>LUBRICATED,</p><p>TENSION,</p><p>77 KSI</p><p>ANODIZED,</p><p>NAS1515 THRU NAS1532NAS108OD7075-T6 AL,</p><p>TYPE,</p><p>900 ˚F (482˚C)</p><p>250 ˚F (121˚C)</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>OR</p><p>NAS1080P()</p><p>NAS1080-()</p><p>B</p><p>B</p><p>A</p><p>C</p><p>C</p><p>C</p><p>BACB30UB()K()</p><p>BACB30UB()K()</p><p>BBACB30NX()K()</p><p>E</p><p>NAS1080R()</p><p>NAS1080R() A B</p><p>C</p><p>C</p><p>BACB30UB()K()</p><p>BACB30NX()K()</p><p>BACB30UB()K() C E</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACB30DX()-()</p><p>BACC30X()BACB30DX()A()</p><p>BACB30DX()A()U BACC30X()S</p><p>BACB30DX()D()N</p><p>BACC30X()</p><p>LOCKBOLT - PROTRUDING HEAD (TENSION)</p><p>TABLE IV</p><p>NAS108ODBACB30GR()-()</p><p>BACB30GP()-()</p><p>NAS108OD</p><p>NAS1080D</p><p>BACC30BF()</p><p>BACC30BF()</p><p>BACC30X()</p><p>BACC30BF()</p><p>BACC30X()</p><p>BACC30BF()</p><p>BACB30NX()K()</p><p>BACB30NX()K()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97196 S0006585419_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 16 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.6</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30NX()K()8740 ALLOY</p><p>STEEL,</p><p>C</p><p>PLATED</p><p>CADMIUM</p><p>DRIVEN),</p><p>HAMMER</p><p>CLOSE</p><p>TOLERANCE</p><p>SHANK,</p><p>BACB30UB()K() C</p><p>A</p><p>A</p><p>CBACB30NX()K()</p><p>BACB30UB()K()</p><p>BACB30MB()A()</p><p>CADMIUM</p><p>160 KSI</p><p>TENSION,</p><p>PLATED,</p><p>BACB30NX()K()</p><p>A286 CRES,</p><p>AC</p><p>B</p><p>B</p><p>B</p><p>(STUMP TYPE,</p><p>LUBRICATED,</p><p>CLOSE</p><p>TOLERANCE</p><p>SHANK,</p><p>(STUMP TYPE,</p><p>MAX TEMP</p><p>HAMMER</p><p>DRIVEN),</p><p>CADMIUM</p><p>BACB30MB()A()UBACC30Q()A286 CRES,</p><p>PASSIVATED,</p><p>160 KSI</p><p>TENSION,</p><p>LUBRICATED,</p><p>CLOSE</p><p>TOLERANCE</p><p>SHANK,</p><p>(STUMP TYPE,</p><p>MAX TEMP</p><p>HAMMER</p><p>DRIVEN),</p><p>BABACB30MB()A()</p><p>250 ˚F (121˚C)</p><p>900 ˚F (482˚C)</p><p>NAS1080</p><p>NAS1080</p><p>NAS1080R</p><p>NAS1080R</p><p>C</p><p>CBACB30NX()K()</p><p>BACB30UB()K()</p><p>C</p><p>BACB30UB()K()</p><p>E</p><p>A B</p><p>A B</p><p>A B</p><p>C E</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACC30X()BACB30HC()-()</p><p>BACC30X()</p><p>BACC30X()</p><p>BACC30X()</p><p>BACB30HC()A()</p><p>BACC30X()PBACB30HC()A()U</p><p>TABLE IV</p><p>LOCKBOLT - PROTRUDING HEAD (TENSION)</p><p>BACC30X()</p><p>BACC30BF()</p><p>BACC30BF()</p><p>BACC30BF()</p><p>BACC30X()</p><p>BACC30BF()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97197 S0006585420_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 17 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.7</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>A GB</p><p>BA</p><p>BA</p><p>250 ˚F (121˚C),</p><p>250 ˚F (121˚C)</p><p>600 ˚F (316˚C)</p><p>JALLOY STEEL,</p><p>6AL-4V BACC30BN()L BACB30XC()HK()</p><p>COMPOSITES</p><p>FOR USE IN</p><p>TITANIUM,</p><p>95 KSI SHEAR,</p><p>STUMP TYPE,</p><p>LIGHTWEIGHT,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>WITH SEALANT</p><p>ESCAPE GROOVE,</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>BACB30NX()K()BACC30BF()6AL-4V</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>95 KSI SHEAR,</p><p>TENSION,</p><p>160 KSI</p><p>TITANIUM,</p><p>TENSION,</p><p>160 KSI</p><p>PLATED,</p><p>NICKEL-CADIMUM</p><p>LUBRICATED,</p><p>CLOSE</p><p>TOLERANCE</p><p>SHANK,</p><p>(STUMP TYPE,</p><p>MAX TEMP</p><p>HAMMER</p><p>DRIVEN),</p><p>BACN10YT()CD</p><p>BACC30X()</p><p>BACB30YD()HK() BACC30BN()L</p><p>LOCKBOLT - PROTRUDING HEAD (TENSION)</p><p>TABLE IV</p><p>BACB30UB()K() BACC30BH()</p><p>BACB30HC()D()N</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97198 S0006585421_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 18 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.8</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>NAS1080</p><p>NAS1080P</p><p>NAS1080R</p><p>BACB30DY()A()</p><p>BACB30DY()A()</p><p>NAS1080R</p><p>NAS1080P</p><p>BACB30DY()A()</p><p>ALLOY STEEL,</p><p>NO ALTERNATIVEA286 CRES,</p><p>CADMIUM</p><p>PLATED,</p><p>LUBRICATED,</p><p>TENSION,</p><p>100 ˚ (MS20426)</p><p>HEAD, PULL</p><p>TYPE, MAX TEMP</p><p>160 KSI</p><p>160 KSI</p><p>TENSION,</p><p>LUBRICATED,</p><p>100 ˚ (MS20426)</p><p>HEAD, PULL</p><p>TYPE, MAX TEMP</p><p>CADMIUM</p><p>PLATED,</p><p>NAS1080D7075-T6 AL, NAS1535 THRU NAS1542 NAS1080D</p><p>PULL TYPE,</p><p>HEAD,</p><p>100 ˚ (MS20426)</p><p>LUBRICATED,</p><p>TENSION,</p><p>77 KSI</p><p>ANODIZED,</p><p>NAS1080</p><p>250 ˚F (121˚C)</p><p>250 ˚F (121˚C)</p><p>NAS1080D</p><p>NAS1080DNAS1535 THRU NAS1542</p><p>BACB30GQ()-() NAS1080D7075-T6 AL,</p><p>CLOSE</p><p>TOLERANCE</p><p>SHANK, STUMP</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>TYPE, MAX TEMP</p><p>250 ˚F (121˚C)</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>BACB30DY()-()</p><p>BACB30DY()A()</p><p>BACB30GQ()-()</p><p>LOCKBOLT - FLUSH HEAD (TENSION)</p><p>TABLE V</p><p>BACB30GS()-()</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97199 S0006585422_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 19 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.9</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACC30Q()BACC30Q()</p><p>BACC30BH() BA</p><p>BABACC30X()</p><p>BACC30X() BA</p><p>BABACC30BH()</p><p>250 ˚F (121˚C)</p><p>250 ˚F (121˚C)</p><p>600 ˚F (316˚C)</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>J</p><p>PLATED,</p><p>160 KSI</p><p>TENSION,</p><p>LUBRICATED,</p><p>100 ˚ (AN509)</p><p>HEAD, STUMP</p><p>TYPE, MAX TEMP</p><p>160 KSI</p><p>TENSION,</p><p>LUBRICATED,</p><p>100 ˚ (MS20426)</p><p>HEAD, STUMP</p><p>TYPE, MAX TEMP</p><p>ALLOY STEEL,</p><p>CADMIUM</p><p>A286 CRES,</p><p>PLATED,</p><p>CADMIUM</p><p>NAS1080</p><p>NAS1080R</p><p>BACB30DY()A() NAS1080</p><p>NAS1080RBACB30DY()A()</p><p>BACB30DY()A()</p><p>NAS1080BACB30DY()A()</p><p>BACB30DY()-()</p><p>BACB30DY()A()</p><p>NAS1080R NAS1080R</p><p>NAS1080R</p><p>NAS1080BACB30DY()-()NAS1080</p><p>NICKEL-CADIUM</p><p>ALLOY STEEL,</p><p>TYPE, MAX TEMP</p><p>HEAD, PULL</p><p>100 ˚ (AN509)</p><p>LUBRICATED,</p><p>TENSION,</p><p>160 KSI</p><p>PLATED,</p><p>DIFFUSED</p><p>GBA</p><p>GBA</p><p>250 ˚F (121˚C)</p><p>HNAS1080</p><p>OR</p><p>NAS1080P</p><p>OR</p><p>NAS1080R</p><p>BACN10YT()CD</p><p>BACB30JC()A()</p><p>95 KSI SHEAR</p><p>UNLUBRICATED</p><p>CAD PLATED,</p><p>ALLOY STEEL,</p><p>PLATED,</p><p>CADMIUM</p><p>100 ˚ (AN509)</p><p>TYPE, MAX TEMP</p><p>HEAD, PULL</p><p>TENSION,</p><p>160 KSI</p><p>LUBRICATED,</p><p>BACB30JC()-()</p><p>BACN10YT()CD</p><p>ALLOY STEEL,</p><p>JNAS1080</p><p>OR</p><p>NAS1080P</p><p>OR</p><p>NAS1080R</p><p>BACB30HD()A()</p><p>BACB30HD()-()</p><p>BACB30GX()D()N</p><p>TABLE V</p><p>LOCKBOLT - FLUSH HEAD (TENSION)</p><p>BACB30GX()-()X</p><p>BACB30GX()-()</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97200 S0006585423_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 20 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.10</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BA</p><p>BABACC30BH()</p><p>NAS1080R</p><p>NAS1080</p><p>HBACB30JC()-()</p><p>BACB30NY()K() B</p><p>BA</p><p>C BACC30X()</p><p>BACC30X()</p><p>A</p><p>H</p><p>C</p><p>250 ˚F (121˚C)</p><p>PLATED,</p><p>CADMIUM</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TENSION,</p><p>160 KSI</p><p>100 ˚ HEAD,</p><p>TITANIUM,</p><p>6AL-4V</p><p>TYPE, MAX TEMP</p><p>HEAD, STUMP</p><p>100 ˚ (AN509)</p><p>LUBRICATED,</p><p>TENSION,</p><p>160 KSI</p><p>BACC30BF() BACB30NY()K()</p><p>A GB</p><p>ALLOY STEEL,</p><p>BACB30NY()K()</p><p>BACB30JC()-()</p><p>BACB30UA()K() C</p><p>BACC30X()</p><p>B</p><p>BA</p><p>BACC30BF()</p><p>BACC30X() A</p><p>BACC30X()</p><p>LOCKBOLT - FLUSH HEAD (TENSION)</p><p>TABLE V</p><p>BACB30UA()K()</p><p>BACN10YT()CD</p><p>BACB30HG()-()</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97201 S0006585424_V2</p><p>Fastener Substitution - Lockbolts</p><p>Figure 3 (Sheet 21 of 21)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 98.11</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>IF SUBSTITUTE RIVETS ARE INSTALLED, YOU</p><p>SUPPLIED WITH SPINDLES THAT HAVE A FULL</p><p>THIS FASTENER IS NOT PERMITTED FOR USE IN</p><p>THESE FASTENERS ARE ONLY PERMITTED FOR</p><p>GIVEN TYPE OF SPINDLE SERRATION.</p><p>USE ONLY THE SPECIFIED TOOL FOR A</p><p>NAS1398-()A() AND NAS1399-()A() HAVE A</p><p>NAS1398-()-() AND NAS1399-()-() HAVE A</p><p>BLIND RIVETS ARE APPROXIMATELY 1/64 INCH</p><p>CONSTANT FOR ALL BACR15CE AND BACR15GF</p><p>PROTECTIVE TREATMENT TO INSTALL FASTENERS.</p><p>NOTES</p><p>THE NOMINAL DIAMETER OF THE BACR15FP,</p><p>NAS1398 AND NAS1399 BLIND RIVETS ARE</p><p>GREATER THAN THE NOMINAL DIAMETER OF</p><p>YOU MUST KEEP THE COUNTERSINK DEPTH</p><p>REFER TO SRM 51-40-05.</p><p>-</p><p>SMOOTH.</p><p>BACR15FR, NAS1738, AND THE NAS1739</p><p>THE ATTACHMENT OF NUTPLATES.</p><p>NOTE:</p><p>SERRATION, OR A PARTIAL SERRATION.</p><p>NAS1398 AND NAS1399 BLIND RIVETS.</p><p>FULL SERRATION.</p><p>PARTIAL SERRATION</p><p>____</p><p>-</p><p>-</p><p>RIVETS.</p><p>REFER TO TABLE I FOR THE FASTENER</p><p>THE INSTALLATION OF FASTENERS.</p><p>SUBSTITUTION INDEX.</p><p>INSTALL THE BLIND RIVETS WET WITH THE</p><p>THE BLIND RIVET IS NOT PERMITTED IN AREAS</p><p>THE BLIND RIVET CAN ONLY BE USED WHEN YOU</p><p>DO NOT HAVE SUFFICIENT ACCESS TO INSTALL</p><p>FUSELAGE FRAMES, FLOOR BEAMS, WING LEADING</p><p>NEAR THE ENGINE INLETS, FUSELAGE SKINS,</p><p>SOLID RIVETS.</p><p>APPLICABLE SEALANT.</p><p>OR TRAILING EDGE STRUCTURE.</p><p>-</p><p>N97097 S0006585321_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 1 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 4</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>6 THROUGH 9</p><p>3 THROUGH 5</p><p>V</p><p>II</p><p>VI</p><p>IV</p><p>III</p><p>16</p><p>13 THROUGH 15</p><p>10 THROUGH 12</p><p>RIVET FASTENER SUBSTITUTION INDEX</p><p>TABLE I</p><p>RIVET - BLIND - FLUSH HEAD</p><p>RIVET - BLIND - PROTRUDING HEAD</p><p>RIVET - SOLID SHANK - PROTRUDING HEAD</p><p>TYPE OF RIVET FASTENER</p><p>RIVET - SLUG</p><p>RIVET - SOLID SHANK - FLUSH HEAD</p><p>LOCATION OF FASTENER</p><p>NUMBER</p><p>TABLE</p><p>NUMBER</p><p>SHEET</p><p>N97098 S0006585322_V1</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 2 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 5</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>E J KI</p><p>JIE</p><p>E J KI</p><p>JIE</p><p>F</p><p>E J KI</p><p>G L</p><p>E I J</p><p>KJIE</p><p>J KIE</p><p>JIE</p><p>L</p><p>J KIE</p><p>JIE</p><p>J KIE</p><p>JIE</p><p>G</p><p>LG</p><p>J KIE</p><p>JIE</p><p>L</p><p>JIE</p><p>BACR15DR()P()</p><p>BACR15DR()PAC()</p><p>BACR15DR()P()</p><p>BACR15DR()PAC()</p><p>MS20470A</p><p>BACR15BB()D()C 2017-T4 AL,</p><p>CONVERSION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK BACR15FT()KE()C</p><p>BACR15DR()PAC()</p><p>BACR15DR()P()</p><p>BACR15BB()A()</p><p>BACR15BB()A()C</p><p>BACR15BB()D()</p><p>BACR15BB()B()C</p><p>BACR15BB()B()</p><p>BACR15BB()AD()C</p><p>BACR15BB()AD()</p><p>1100-F AL,</p><p>CONVERSION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>2117-T4 AL,</p><p>ANODIZED OR</p><p>CONVERSION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15BB()AD()C</p><p>BACR15DR()P()</p><p>BACR15DR()PAC()</p><p>BACR15DR()P()</p><p>BACR15DR()P()</p><p>BACR15DR()PAC()</p><p>BACR15DR()P()</p><p>BACR15DR()PAC()</p><p>BACR15BB()B()C</p><p>BACR15BB()DD()</p><p>BACR15DR()P()</p><p>BACR15DR()PAC()</p><p>BACR15FT()D()</p><p>BACR15FT()KE()C</p><p>MS20470DD</p><p>BACR15BB()D()C</p><p>BACR15FT()AD</p><p>BACR15DR()PAC()</p><p>5056-H32 AL,</p><p>ANODIZED OR</p><p>CONVERION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>5056-H32 AL,</p><p>CONVERSION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>2017-T4 AL,</p><p>ANODIZED OR</p><p>CONVERSION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>2117-T4 AL,</p><p>CONVERSION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>MS20470D</p><p>MS20470AD</p><p>1100F AL,</p><p>ANODIZED, CLOSE</p><p>TOLERANCE SHANK</p><p>BACR15AY()-() ALLOY STEEL</p><p>HI SHEAR</p><p>FLAT HEAD</p><p>INTERFERENCE F17</p><p>160 KSI</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>RIVET - SOLID SHANK - PROTRUDING HEAD</p><p>TABLE II N97099 S0006585323_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 3 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 6</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>I KJE</p><p>I JE</p><p>LJ</p><p>L</p><p>G</p><p>N</p><p>N</p><p>N</p><p>N</p><p>N</p><p>N</p><p>N</p><p>PART NUMBER ALTERNATIVEEQUIVALENTDESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACR15FT()DD()</p><p>BACR15DR()P()</p><p>BACR15DR()PAC()</p><p>2024-T4 AL,</p><p>ANODIZED, CLOSE</p><p>TOLERANCE SHANK</p><p>MS20470DDBACR15BB()DD()</p><p>MONEL, CLOSE</p><p>TOLERANCE SHANK</p><p>BACR15FT()KE()C</p><p>NASM20615-()M()BACR15DX()M()</p><p>BACR15DX()-() A286 CRES</p><p>UNIVERSAL HEAD</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>NAS1198()-()</p><p>NAS1242B</p><p>NAS1242DD</p><p>2017-T4 AL,</p><p>ANODIZED, UNIVERSAL</p><p>HEAD, CLOSE</p><p>TOLERANCE SHANK,</p><p>0.031 OVERSIZE</p><p>NAS1242D</p><p>NAS1242DD2024-T4 AL,</p><p>ANODIZED, UNIVERSAL</p><p>HEAD, CLOSE</p><p>TOLERANCE SHANK,</p><p>0.031 OVERSIZE</p><p>2117-T4 AL,</p><p>ANODIZED, MODIFIED</p><p>UNIVERSAL HEAD,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15BB()AD()</p><p>MS20470AD</p><p>BACR15BB()AD()C</p><p>5056-H32 AL,</p><p>ANODIZED, UNIVERSAL</p><p>HEAD, CLOSE</p><p>TOLERANCE SHANK,</p><p>0.031 OVERSIZE</p><p>NAS1242AD2117-T4 AL,</p><p>ANODIZED, UNIVERSAL</p><p>HEAD, CLOSE</p><p>TOLERANCE SHANK,</p><p>0.031 OVERSIZE</p><p>BACR15ET()B()</p><p>BACR15ET()D()</p><p>BACR15ET()DD()</p><p>BACR15FT()AD()</p><p>BACR15ET()AD()</p><p>MS20470D</p><p>2017-T4 AL,</p><p>ANODIZED, MODIFIED</p><p>UNIVERSAL HEAD,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15FT()D()</p><p>MS20470DD</p><p>BACR15BB()DD()</p><p>BACR15BB()D()</p><p>BACR15FT()KE()C</p><p>RIVET - SOLID SHANK - PROTRUDING HEAD</p><p>TABLE II N97100 S0006585324_V1</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 4 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 7</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>N</p><p>LJG</p><p>N</p><p>JIE</p><p>KJIE</p><p>N</p><p>N</p><p>ALTERNATIVE</p><p>FASTENER SUBSTITUTION</p><p>EQUIVALENT</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>DESCRIPTIONPART NUMBER</p><p>BACR15FT()DD()</p><p>MS20470DD</p><p>BACR15FT()KE()C</p><p>CLOSE TOLERANCE</p><p>UNIVERSAL HEAD,</p><p>ANODIZED, MODIFIED</p><p>2024-T4 AL,</p><p>SHANK</p><p>7050-T73 AL,</p><p>TOLERANCE SHANK</p><p>HEAD, CLOSE</p><p>MODIFIED UNIVERSAL</p><p>CONVERSION COATED,</p><p>BACR15FT()KE()C</p><p>1100-F AL, BACR15BB()A()</p><p>UNIVERSAL HEAD</p><p>BACR15BB()AD()</p><p>ANODIZED, UNIVERSAL</p><p>HEAD</p><p>2117-T4 AL,</p><p>BACR15BB()B()</p><p>HEAD</p><p>5056-H32 AL,</p><p>ANODIZED, UNIVERSAL</p><p>HEAD</p><p>ANODIZED, UNIVERSAL</p><p>2017-T4 AL,</p><p>ANODIZED, UNIVERSAL</p><p>HEAD</p><p>BACR15BB()DD()2024-T4 AL,</p><p>UNIVERSAL HEAD</p><p>7050-T73 AL,</p><p>BACR15DX()M()MONEL</p><p>BACR15DX()-()A286 CRES</p><p>MS20470E</p><p>NAS1198</p><p>MS20470A</p><p>BACR15BB()D()</p><p>MS20470B()-()</p><p>MS20470DD</p><p>MS20615()M</p><p>MS20470AD()-()</p><p>MS20470D()-()</p><p>BACR15BB()DD()</p><p>BACR15DR()PAC()</p><p>BACR15DR()P()</p><p>BACR15FT()DD()</p><p>BACR15BB()DD()</p><p>BACR15FT()A()C</p><p>BACR15FT()B()C</p><p>BACR15FT()DD() L</p><p>MS20470DD</p><p>NO ALTERNATIVE</p><p>NO ALTERNATIVE</p><p>BACR15FT()AD() L</p><p>BACR15BB()AD()C</p><p>GBACR15FT()KE()C L</p><p>BACR15BB()DD()</p><p>BACR15BB()D()C</p><p>LGBACR15FT()D()</p><p>BACR15FT()DD() L</p><p>MS20470DD</p><p>BACR15BB()DD()</p><p>BACR15FT()KE()C L</p><p>MS20470DD</p><p>RIVET - SOLID SHANK - PROTRUDING HEAD</p><p>TABLE II</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97101 S0006585325_V3</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 5 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 8</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>E KI J</p><p>E I J</p><p>E KI J</p><p>E I J</p><p>F</p><p>BACR15BA()AD()C</p><p>BACR15BA()AD()</p><p>KE JI</p><p>E JI</p><p>E JI</p><p>JI</p><p>I KJ</p><p>JIE</p><p>E</p><p>E</p><p>NAS1241B</p><p>NAS1241AD</p><p>BACR15DR()-()</p><p>BACR15DR()AC()</p><p>BACR15DR()-()</p><p>BACR15DR()AC()</p><p>MS20426A</p><p>RIVET - SOLID SHANK - FLUSH HEAD</p><p>TABLE III</p><p>BACR15BA()A()C 1100-F AL,</p><p>100 ˚ PRECISION HEAD,</p><p>BACR15DR()-()2117-T4 AL,</p><p>CONVERSION COATED,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15GE()CW()</p><p>BACR15DR()AC()</p><p>BACR15GE()CW()</p><p>BACR15DR()-()</p><p>BACR15DR()AC()</p><p>BACR15BA()AD()C</p><p>CLOSE TOLERANCE</p><p>PRECISION HEAD,</p><p>2117-T4 AL, ANODIZED</p><p>SHANK</p><p>COATED, 100 ˚</p><p>OR CONVERSION</p><p>MS20426AD</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>100 ˚ PRECISION HEAD,</p><p>CONVERSION COATED,</p><p>TOLERANCE SHANK</p><p>100 ˚ HEAD, CLOSE</p><p>1100F AL, ANODIZED,</p><p>160 KSI</p><p>BACR15BA()A()</p><p>BACR15AZ()-()</p><p>INTERFERENCE FIT</p><p>100 ˚ HEAD</p><p>HI SHEAR</p><p>ALLOY STEEL</p><p>0.031 OVERSIZE</p><p>BACR15AD()B()</p><p>BACR15AD()DD()</p><p>5056-H32 AL,</p><p>ANODIZED, 100 ˚ HEAD,</p><p>BACR15AD()D() NAS1241DD2017-T4 AL,</p><p>NAS1241D</p><p>0.031 OVERSIZE</p><p>ANODIZED, 100 ˚ HEAD,</p><p>BACR15AD()AD()</p><p>NAS1241DD2024-T4 AL,</p><p>ANODIZED, 100 ˚ HEAD,</p><p>0.031 OVERSIZE</p><p>2117-T4 AL,</p><p>0.031 OVERSIZE</p><p>ANODIZED, 100 ˚ HEAD,</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97102 S0006585326_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 6 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 9</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY</p><p>- See title page for details</p><p>E</p><p>E</p><p>E</p><p>E</p><p>E</p><p>E</p><p>E</p><p>E</p><p>E</p><p>E</p><p>E</p><p>A</p><p>A</p><p>A</p><p>A</p><p>A</p><p>A</p><p>A</p><p>A</p><p>A</p><p>I J K</p><p>I J</p><p>I J K</p><p>I J</p><p>I J K</p><p>I J</p><p>O</p><p>PART NUMBER ALTERNATIVEEQUIVALENTDESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACR15BA()B() 5056F AL, ANODIZED,</p><p>100 ˚ HEAD, CLOSE</p><p>TOLERANCE SHANK</p><p>2017-T3 AL,</p><p>CONVERSION COATED,</p><p>100 ˚ PRECISION HEAD,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15DR()AC()</p><p>BACR15BA()D()C</p><p>BACR15BA()DD()</p><p>MS20426D</p><p>BACR15DR()-()</p><p>BACR15DR()AC()</p><p>5056-H32 AL,</p><p>CONVERSION COATED,</p><p>100 ˚ PRECISION HEAD,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15DR()-()</p><p>BACR15BA()D()</p><p>BACR15BA()B()C</p><p>MS20426DD</p><p>MS20426DD2024-T4 AL,</p><p>ANODIZED,</p><p>100 ˚ PRECISION HEAD,</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15DR()-()</p><p>BACR15DR()AC()</p><p>2117-T4 AL,</p><p>ANODIZED, 100 ˚</p><p>SHEAR HEAD MS20426AD</p><p>BACR15BA()AD</p><p>NAS1097AD</p><p>5056-H32 AL,</p><p>ANODIZED, 100 ˚</p><p>SHEAR HEAD</p><p>2017-T4 AL,</p><p>CONVERSION COATED,</p><p>100 ˚ SHEAR HEAD</p><p>MS20426DD</p><p>MS20426D</p><p>BACR15BA()DD()</p><p>NAS1097D</p><p>BACR15BA()D()</p><p>NAS1200M</p><p>MS20427M</p><p>MONEL, 100 ˚ SHEAR</p><p>HEAD</p><p>BACR15GF()D()</p><p>BACR15BA()DD()</p><p>BACR15CE()AD()</p><p>BACR15CE()M()</p><p>BACR15CE()B()</p><p>BACR15CE()D()</p><p>NAS1097B</p><p>RIVET - SOLID SHANK - FLUSH HEAD</p><p>TABLE III</p><p>MS20426B</p><p>BACR15BA()B</p><p>BACR15BA()AD()</p><p>BACR15BA()D()</p><p>MS20426AD</p><p>MS20426B</p><p>MS20426D</p><p>N97103 S0006585327_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 7 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 10</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>E I J</p><p>E I J</p><p>KE I</p><p>E</p><p>J</p><p>I J</p><p>H</p><p>H</p><p>H</p><p>P</p><p>H</p><p>PART NUMBER ALTERNATIVEEQUIVALENTDESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>BACR15CE()D()</p><p>HEAD)</p><p>HEAD)</p><p>2024-T4 AL,</p><p>ANODIZED, MODIFIED,</p><p>82 ˚ HEAD (INDEX</p><p>ANODIZED, MODIFIED,</p><p>82 ˚ HEAD (INDEX</p><p>ANODIZED, MODIFIED</p><p>82 ˚ HEAD (INDEX</p><p>HEAD)</p><p>CONVERSION COATED,</p><p>100 ˚ PRECISION</p><p>2017-T4 AL,BACR15GF()D()</p><p>BACR15FH()DD()</p><p>SHEAR HEAD</p><p>BACR15FH()KE() 7050-T73 AL,</p><p>BACR15GH()KE() 7050-T73 AL,</p><p>ANODIZED, INDEX HEAD</p><p>BACR15GE()CW()</p><p>BACR15GE()C()</p><p>BACR15DR()-()</p><p>BACR15DR()AC()</p><p>2117-T4 AL,</p><p>PLATED, 100 ˚ HEAD</p><p>MONEL, CADMIUM</p><p>ANODIZED, 100 ˚ HEAD</p><p>MONEL, 100 ˚ HEAD</p><p>2024-T4 AL,</p><p>2017-T4 AL,</p><p>ANODIZED, 100 ˚ HEAD</p><p>ANODIZED, 100 ˚ HEAD</p><p>MS20426AD</p><p>MS20427M()</p><p>MS20427M()C()</p><p>MS20426DD</p><p>BACR15FH()AD() 2117-T4 AL,</p><p>A286 CRES</p><p>100 ˚ SHEAR HEAD</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>MONEL</p><p>100 ˚ SHEAR HEAD</p><p>CLOSE TOLERANCE</p><p>SHANK</p><p>BACR15DY()-()</p><p>BACR15DY()M()</p><p>NAS1200()-()</p><p>NAS1200M()-()</p><p>BACR15BA()AD()</p><p>BACR15BA()DD()</p><p>BACR15BA()D()MS20426D()-()</p><p>MS20426DD</p><p>BACR15BA()DD</p><p>BACR15BA()D()C</p><p>MS20426AD</p><p>BACR15BA()AD()C</p><p>RIVET - SOLID SHANK - FLUSH HEAD</p><p>TABLE III</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97104 S0006585328_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 8 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 11</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>JIE</p><p>KJIE</p><p>BACR15BA()B()</p><p>BACR15BA()A()</p><p>NO ALTERNATIVE</p><p>BACR15DR()AC()</p><p>BACR15DR()-()</p><p>HEAD</p><p>7050-T73 AL,MS14218E()-()</p><p>RIVET - SOLID SHANK - FLUSH HEAD</p><p>TABLE III</p><p>HEAD</p><p>120 ˚ MODIFIED SHEAR</p><p>NO ALTERNATIVE</p><p>BACR15FV()KE()</p><p>MS14218E()-()</p><p>INTERFERENCE SHEAR</p><p>120 ˚ FLUSH</p><p>CONVERSION COATED,</p><p>ANODIZED OR</p><p>BACR15FV()KE()</p><p>CONVERSION COATED,</p><p>ANODIZED OR</p><p>7050-T73 AL,</p><p>ANODIZED, 100 ˚ HEAD</p><p>MS20426B 5056-H32 AL,</p><p>MS20426A 1100-F, 100 ˚ HEAD</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>N97105 S0006585329_V1</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 9 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 12</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BLIND SELF</p><p>PLUGGING</p><p>5056-F ALBACR15DA()-()</p><p>5056-F AL</p><p>BLIND-PULL THRU</p><p>BACR15DA()H()</p><p>NAS1738B()-()</p><p>BACR15FR()E()R</p><p>NAS1398B()-()</p><p>NAS1738E()-()</p><p>MS20604B()W()</p><p>BACR15FR()E()R</p><p>MS20604B()T()</p><p>NAS1398B()-()</p><p>NAS1738B()-()</p><p>NAS1738E()-()</p><p>MS20470D</p><p>BACR15DR()PAC()</p><p>UNIVERSAL HEAD</p><p>450 ˚F (232˚C),</p><p>BACR15DR()P()</p><p>BACR15FT()D()</p><p>BACR15BB()D</p><p>PLATED, MAX TEMP</p><p>STEEL SLEEVE, CAD</p><p>THRU TYPE), C1018</p><p>NONSTRUCTURAL (PULL</p><p>D</p><p>D</p><p>D</p><p>NAS1398D()-()NAS1398B()-()</p><p>UNIVERSAL HEAD</p><p>MAX TEMP 250 ˚F,</p><p>STEM,</p><p>PARTIAL SERRATED</p><p>LOCKED SPINDLE,</p><p>5056 AL SLEEVE,</p><p>NAS1738B B</p><p>B</p><p>B</p><p>B</p><p>EC</p><p>ECC</p><p>AF2050-()-()</p><p>CR2263-()-()</p><p>ALLFAST</p><p>CHERRY</p><p>BACR15FR()E()R</p><p>BACR15FR()E()</p><p>NAS398D()A()</p><p>NAS1738E</p><p>TABLE IV</p><p>HR3253-()-()HUCK</p><p>CHERRY CR3253-()-()</p><p>BACR15FR()E()R</p><p>RIVET - BLIND - PROTRUDING HEAD</p><p>CR6253-()-()</p><p>NO ALTERNATIVECHERRY</p><p>MAX TEMP 250 ˚F</p><p>OVERSIZED DIAMETER,</p><p>UNIVERSAL HEAD,</p><p>LOCK COLLAR,</p><p>STEM, A-286 CRES</p><p>SLEEVE, A-286 CRES</p><p>CHERRY SST, 5056 AL</p><p>MAX TEMP 250 ˚F</p><p>SPINDLE-BULBED,</p><p>SLEEVE, LOCKED</p><p>CRES STEM, 5056 AL</p><p>CHERRY-MAX SYSTEM, AF3253-()-()BALLFAST NO ALTERNATIVE</p><p>PART NUMBER ALTERNATIVEEQUIVALENTDESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>BULBED CHERRYLOCK,</p><p>SELF-PLUGGING, 5056</p><p>BACR15EB-P()-()</p><p>AL SLEEVE. MAX TEMP</p><p>250 ˚F (121˚C)</p><p>BACR15FR()E()R</p><p>NAS1738MW</p><p>NAS1738E</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97106 S0006585330_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 10 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 13</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>C</p><p>C</p><p>C</p><p>C</p><p>C</p><p>C</p><p>C</p><p>B</p><p>B</p><p>C</p><p>B</p><p>B</p><p>C B</p><p>B</p><p>C</p><p>B</p><p>B</p><p>NAS1398C()A()NAS1398C()-() A-286 CRES SLEEVE,</p><p>MAX TEMP 1200˚F</p><p>STEM,</p><p>PARTIAL SERRATED</p><p>LOCKED SPINDLE,</p><p>CC CR2663-()-()</p><p>AF2040-()-()ALLFAST</p><p>CHERRY</p><p>PART NUMBER ALTERNATIVEEQUIVALENTDESCRIPTION</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>FASTENER SUBSTITUTION</p><p>NAS1738E</p><p>NAS1738B</p><p>A-286 CRES SLEEVE,</p><p>CADMIUM PLATED,</p><p>LOCKED SPINDLE,</p><p>PARTIAL SERRATED</p><p>A-286 CRES SLEEVE,</p><p>CADMIUM PLATED,</p><p>A-286 CRES SLEEVE,</p><p>LOCKED SPINDLE,</p><p>PARTIAL SERRATED</p><p>2017 AL SLEEVE,</p><p>CHERRY</p><p>ALLFAST</p><p>NAS1398C()-()</p><p>NAS1398CW()A()</p><p>NAS1398CW()-()</p><p>BACR15FR()E()</p><p>BACR15FR()E()R</p><p>NAS1398D()A()</p><p>CHERRY</p><p>ALLFAST</p><p>CR2673-()-()</p><p>ALLFAST</p><p>CHERRY CR2673CW-()-()</p><p>RV1240W-()-()</p><p>AF2040W-()-()</p><p>CR2663CW-()-()</p><p>ALLFAST AF2000-()-()</p><p>CHERRY CR2163-()-()</p><p>RV1240-()-()</p><p>NAS1398C()A()</p><p>NAS1398CW()-()</p><p>NAS1398CW()A()</p><p>NAS1398D()-()</p><p>LOCKED SPINDLE, FULL</p><p>SERRATED STEM, MAX</p><p>TEMP 1200˚F (649˚C)</p><p>STEM, MAX TEMP</p><p>450 ˚F (232˚C)</p><p>LOCKED SPINDLE, FULL</p><p>SERRATED STEM, MAX</p><p>TEMP 450 ˚F (232˚C)</p><p>STEM, MAX TEMP</p><p>250 ˚F (121˚C)</p><p>RIVET - BLIND - PROTRUDING HEAD</p><p>TABLE IV</p><p>250 ˚F (121˚C)</p><p>MAX TEMP</p><p>NAS1398D()A()</p><p>SERRATED STEM,</p><p>LOCKED SPINDLE, FULL</p><p>NAS1738B</p><p>NAS1738E</p><p>CHERRY</p><p>BACR15FR()E()R</p><p>NAS1398D()-()</p><p>CR2173-()-()</p><p>ALLFAST2017 AL SLEEVE, BACR15FR()E()RV1200-()-()</p><p>RV1250-()-()</p><p>CR2273-()-()</p><p>ALLFAST</p><p>CHERRY</p><p>NAS1398D()A()</p><p>NAS1398D()-()</p><p>NAS1398B()-()</p><p>BACR15FR()E()R</p><p>BACR15FR()E()NAS1398B()A()</p><p>NAS1738B</p><p>NAS1738E</p><p>5056 AL SLEEVE,</p><p>MAX TEMP 250 ˚F</p><p>FULL SERRATED STEM,</p><p>LOCKED SPINDLE,</p><p>B</p><p>B</p><p>EC</p><p>EC</p><p>C</p><p>B</p><p>BC</p><p>N97107 S0006585331_V1</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 11 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 14</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>NAS1738B()-() NAS1738E</p><p>BACR15FR()E()R</p><p>BACR15FR()E</p><p>UNIVERSAL HEAD</p><p>MAX TEMP 250 ˚F,</p><p>SPINDLE, BULBED,</p><p>MECHANICALLY LOCKED</p><p>5056 AL SLEEVE, CR2249-()-()CHERRY</p><p>TEMP 450 ˚F (232˚C)</p><p>SPINDLE, BULBED, MAX</p><p>TEMP 900 ˚F (482˚C)</p><p>SPINDLE, BULBED, MAX</p><p>TEMP 250 ˚F (121˚C)</p><p>SPINDLE, BULBED, MAX</p><p>TEMP 450 ˚F (232˚C)</p><p>SERRATED STEM, MAX</p><p>LOCKED SPINDLE, FULL</p><p>450 ˚F (232˚C)</p><p>STEM, MAX TEMP</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>900 ˚F (482˚C)</p><p>STEM, MAX TEMP</p><p>RIVET - BLIND - PROTRUDING HEAD</p><p>TABLE IV</p><p>CR2573-()-()</p><p>RV1290M-()-()</p><p>CR2563M-()-()</p><p>NAS1738MW()-()</p><p>NAS1738M()-()</p><p>NAS1738E()-()</p><p>AF2290W-()-()</p><p>CR2539P-()-()</p><p>CR2239-()-()</p><p>CR2573P-()-()</p><p>AF2090W-()-()NAS1398MW()-()</p><p>NAS1398MW()A()</p><p>AF2290-()-()</p><p>CR2539-()-()</p><p>AF2550-()-()</p><p>RV1290-()-()</p><p>CR2563-()-()</p><p>CHERRY</p><p>ALLFAST</p><p>BACR15FR()M()</p><p>BACR15FR()E()</p><p>ALLFAST</p><p>ALLFAST</p><p>CHERRY</p><p>CHERRY</p><p>NAS1738MW</p><p>BACR15FR()M()R</p><p>NAS1738MW</p><p>BACR15FR()E()R</p><p>NAS1398MW()A()</p><p>NAS1398MW()-()</p><p>BACR15FR()MP()CHERRY</p><p>CHERRY</p><p>ALLFAST</p><p>ALLFAST</p><p>MECHANICALLY LOCKED</p><p>MECHANICALLY LOCKED</p><p>MONEL SLEEVE,</p><p>MONEL SLEEVE,</p><p>MECHANICALLY LOCKED</p><p>5056 AL SLEEVE,</p><p>PARTIAL SERRATED</p><p>LOCKED SPINDLE,</p><p>CADMIUM PLATED,</p><p>MONEL SLEEVE,</p><p>MONEL SLEEVE,</p><p>CADMIUM PLATED,</p><p>NAS1398M()-() ALLFASTMONEL SLEEVE,</p><p>LOCKED SPINDLE,</p><p>PARTIAL SERRATED</p><p>NAS1738M</p><p>NAS1738M</p><p>ALLFASTMONEL SLEEVE,</p><p>LOCKED SPINDLE,</p><p>FULL SERRATED STEM,</p><p>CHERRY</p><p>CHERRY</p><p>BACR15FR()M()</p><p>BACR15FR()M()R</p><p>NAS1398M()A()</p><p>BACR15FR()M()</p><p>BACR15FR()M()R</p><p>NAS1398M()-()</p><p>AF2090M-()-()</p><p>NAS1398M()A()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>UNIVERSAL HEAD</p><p>MECHANICALLY LOCKED</p><p>INCONEL 600 SLEEVE,NAS1738C</p><p>SPINDLE, BULBED, MAX</p><p>TEMP 250 ˚F (121˚C),</p><p>C</p><p>C</p><p>B</p><p>B</p><p>C</p><p>C</p><p>B</p><p>B</p><p>C</p><p>C</p><p>B</p><p>B</p><p>C</p><p>B</p><p>B</p><p>C</p><p>M</p><p>CHERRY NO ALTERNATIVECR2839-()-()</p><p>N97108 S0006585332_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 12 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 15</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>CHERRY SST, 5056 AL</p><p>SLEEVE, 8740 ALLOY</p><p>STEEL STEM, A-286</p><p>CRES LOCK COLLAR,</p><p>UNIVERSAL HEAD,</p><p>NOMINAL DIAMETER,</p><p>MAX TEMP 250 ˚F.</p><p>CHERRY SST, 5056 AL</p><p>SLEEVE, 15-7 PH CRES</p><p>STEM, A-286 CRES</p><p>LOCK COLLAR,</p><p>UNIVERSAL HEAD,</p><p>NOMINAL DIAMETER,</p><p>MAX TEMP 250 ˚F.</p><p>RIVET - BLIND - PROTRUDING HEAD</p><p>TABLE IV</p><p>PART NUMBER ALTERNATIVEEQUIVALENTDESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>CR3213-()-()</p><p>NO ALTERNATIVECHERRY</p><p>CR3223-()-()</p><p>NO ALTERNATIVECHERRY</p><p>2469510 S0000577298_V1</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 13 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 16</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>B</p><p>B</p><p>C B</p><p>B</p><p>C</p><p>C E</p><p>EC</p><p>C</p><p>B</p><p>B</p><p>EC</p><p>EC</p><p>B</p><p>BC</p><p>D</p><p>D</p><p>NAS1739B</p><p>NAS1739E</p><p>BACR15FP()E()NAS1399B()-()</p><p>TEMP 250 ˚F (121˚C)</p><p>SERRATED STEM, MAX</p><p>LOCKED SPINDLE,</p><p>5056 AL SLEEVE,</p><p>100 ˚ HEAD, PARTIAL VOI-SHAN</p><p>ALLFAST</p><p>CHERRY</p><p>CR9262-()A()</p><p>AF2051-()-()</p><p>CR2262-()-()</p><p>BACR15FP()E()R</p><p>NAS1399B()A()</p><p>NAS1399D()-()</p><p>NAS1399D()A()</p><p>250 ˚F (121˚C)</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>100 ˚ HEAD, MAX TEMP</p><p>250 ˚F (121˚C)</p><p>AL SLEEVE. MAX TEMP</p><p>450 ˚F (232˚C)</p><p>100 ˚ HEAD, MAX TEMP</p><p>NAS1739B</p><p>NAS1739MW</p><p>NAS1739E</p><p>BACR15EB()-()</p><p>SELF-PLUGGING, 5056</p><p>BULBED CHERRYLOCK, BACR15FP()E()R</p><p>CHERRY-MAX SYSTEM,</p><p>CADMIUM PLATED,</p><p>5056 AL SLEEVE,</p><p>AF3252-()-()BALLFAST</p><p>HR3252-()-()</p><p>CR3252-()-()</p><p>HUCK</p><p>CHERRY</p><p>BACR15FP()E()R</p><p>MS20605B()W()</p><p>MS20605B()T()</p><p>NAS1739E()-()</p><p>NAS1739B()-()</p><p>NAS1399B()-()</p><p>BACR15DA()CH()</p><p>HEAD PULL THRU</p><p>5056-F BLIND 100 ˚ BACR15FP()E()R</p><p>NAS1399B()-()</p><p>BACR15DA()C() 5056-F BLIND 100 ˚</p><p>HEAD SELF PLUGGING</p><p>BACR15FP()E()R</p><p>TABLE V</p><p>RIVET - BLIND - FLUSH HEAD</p><p>NAS1399B()A()</p><p>CR2262-()-()</p><p>RV1251-()-()</p><p>CHERRY</p><p>ALLFAST</p><p>CR2272-()-()</p><p>NO ALTERNATIVE</p><p>CHERRY</p><p>100 ˚ HEAD,</p><p>FULL SERRATED STEM,</p><p>LOCKED SPINDLE,</p><p>5056 AL SLEEVE, BACR15FP()E()</p><p>NAS1739E</p><p>NAS1739B</p><p>NAS1399D()A()</p><p>NAS1399D()-()</p><p>NAS1399B()-()</p><p>BACR15FP()E()R</p><p>BACR15DR()-() CCR264SS-()-()</p><p>AF5171-()-()</p><p>NON-STRUCTURAL</p><p>CADMIUM PLATED,</p><p>C1018 STEEL SLEEVE,</p><p>(PULL THRU TYPE),</p><p>CHERRY</p><p>ALLFAST</p><p>BACR15BA()AD()C</p><p>BACR15GE()CW()</p><p>BACR15DR()AC()</p><p>BACR15BA()D()C</p><p>NAS1739E()-()</p><p>NAS1739B()-()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97109 S0006585333_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 14 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 17</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>C C</p><p>CR2662CW-()-()</p><p>NAS1399CW()-() NAS1399CW()A()A-286 CRES SLEEVE,</p><p>CAD PLATED, LOCKED</p><p>SPINDLE, 100 ˚ HEAD,</p><p>PARTIAL SERRATED</p><p>STEM, MAX TEMP 450 ˚F</p><p>ALLFAST</p><p>CHERRY</p><p>AF2041W-()-()</p><p>B</p><p>B</p><p>VOI-SHAN</p><p>RV1241W-()-()</p><p>AF2091-()-()</p><p>CR2562M-()()</p><p>RV1201-()-()</p><p>CR2172-()-()</p><p>CR9162-()A()</p><p>CR2162-()-()CHERRY</p><p>ALLFAST</p><p>AF2001W-()-()</p><p>CR2162-()-()</p><p>CR9162-()A()VOI-SHAN</p><p>ALLFAST</p><p>CR2662W-()-()CHERRY</p><p>ALLFAST</p><p>CR2662-()-()</p><p>RV1241-()-()</p><p>CHERRY</p><p>ALLFAST</p><p>CR2672-()-()NAS1399C()A() C C</p><p>CHERRY</p><p>CR2672CW-()-()CHERRY</p><p>CHERRY</p><p>ALLFAST</p><p>CHERRY</p><p>A-286 CRES SLEEVE,</p><p>LOCKED SPINDLE,</p><p>100 ˚ HEAD, FULL</p><p>SERRATED STEM,</p><p>MAX TEMP 1200˚F</p><p>CHERRY NAS1399C()-()</p><p>C</p><p>C</p><p>C</p><p>C</p><p>C</p><p>B</p><p>B</p><p>C</p><p>B</p><p>B</p><p>B</p><p>C</p><p>B</p><p>B</p><p>C</p><p>B</p><p>B</p><p>RIVET - BLIND - FLUSH HEAD</p><p>TABLE V</p><p>NAS1399D()A()</p><p>NAS1399M()-()</p><p>NAS1399CW()A()</p><p>NAS1399D()-()</p><p>100 ˚ HEAD, PARTIAL</p><p>MAX TEMP 900 ˚F</p><p>SERRATED STEM,</p><p>LOCKED SPINDLE,</p><p>MONEL SLEEVE,</p><p>MAX TEMP 250 ˚F</p><p>SERRATED STEM,</p><p>100 ˚ HEAD, FULL</p><p>LOCKED SPINDLE,</p><p>2017 AL SLEEVE,</p><p>100 ˚ HEAD, PARTIAL</p><p>A-286 CRES SLEEVE,</p><p>2017 AL SLEEVE,</p><p>MAX TEMP 250 ˚F</p><p>SERRATED STEM,</p><p>LOCKED SPINDLE,</p><p>MAX TEMP 450 ˚F</p><p>SERRATED STEM,</p><p>100 ˚ HEAD, FULL</p><p>LOCKED SPINDLE,</p><p>CADMIUM PLATED,</p><p>NAS1739M</p><p>NAS1739E</p><p>BACR15FP()E()</p><p>NAS1399M()A()</p><p>BACR15FP()M()R</p><p>BACR15FP()M()</p><p>NAS1739E()-()</p><p>NAS1399D()-()</p><p>NAS1739B()-()</p><p>BACR15FP()E()R</p><p>NAS1739B</p><p>NAS1399D()A()</p><p>BACR15FP()E()R</p><p>BACR15FP()E()</p><p>NAS1399CW()-()</p><p>NAS1399C()-() CR2662-()-() NAS1399C()A()CHERRY</p><p>LOCKED SPINDLE,</p><p>SERRATED STEM,</p><p>MAX TEMP 250 ˚F</p><p>100 ˚ HEAD, PARTIAL</p><p>A-286 CRES SLEEVE,</p><p>ALLFAST AF2041-()-()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>N97110 S0006585334_V1</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 15 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 18</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACR15FP()E()</p><p>BACR15FP()E()R</p><p>NAS1739E</p><p>NO ALTERNATIVECR2838-()-()</p><p>CR2248-()-()</p><p>NAS1739C</p><p>NAS1739B</p><p>SPINDLE, BULBED</p><p>CHERRY</p><p>CHERRY</p><p>MECHANICALLY LOCKED</p><p>INCONEL 600 SLEEVE,</p><p>MECHANICALLY LOCKED</p><p>100 ˚ HEAD,</p><p>MAX TEMP 250 ˚F</p><p>SPINDLE, BULBED,</p><p>100 ˚ HEAD,</p><p>5056 AL SLEEVE,</p><p>C</p><p>B</p><p>CR2562-()-()</p><p>CR2538P-()-()</p><p>AF2291W-()-()</p><p>CR2538-()-()</p><p>AF2291-()-()</p><p>CR3252-()-()</p><p>CR2238()-()</p><p>BACR15FP()E()</p><p>CHERRY</p><p>CHERRY</p><p>CR2572P-()-()</p><p>CHERRY</p><p>CHERRY</p><p>RV1291-()-() C</p><p>AF2551()-()</p><p>CHERRY</p><p>ALLFAST</p><p>CHERRY</p><p>ALLFAST</p><p>ALLFAST</p><p>ALLFASTC</p><p>M</p><p>B</p><p>AF2091W-()-()</p><p>CR2562-()-()</p><p>CR2562M-()-()</p><p>RV1291M-()-()</p><p>CHERRY</p><p>ALLFAST</p><p>CR2572-()-()</p><p>B</p><p>C</p><p>BC CHERRY</p><p>ALLFAST</p><p>CHERRY BC</p><p>RIVET - BLIND - FLUSH HEAD</p><p>TABLE V</p><p>NAS1739E()-()</p><p>NAS1399MW()A()</p><p>NAS1739MW</p><p>NAS1739M</p><p>FULL SERRATED STEM,</p><p>MONEL SLEEVE,</p><p>MAX TEMP 450 ˚F</p><p>LOCKED SPINDLE,</p><p>MECHANICALLY</p><p>100 ˚ HEAD,</p><p>CADMIUM PLATED,</p><p>BULBED,</p><p>MAX TEMP 900 ˚F</p><p>LOCKED SPINDLE,</p><p>MECHANICALLY</p><p>100 ˚ HEAD,</p><p>BULBED,</p><p>MONEL SLEEVE,</p><p>MAX TEMP 250 ˚F</p><p>LOCKED SPINDLE,</p><p>MECHANICALLY</p><p>100 ˚ HEAD,</p><p>BULBED,</p><p>5056 AL SLEEVE,</p><p>MAX TEMP 450 ˚F</p><p>100 ˚ HEAD,</p><p>LOCKED SPINDLE,</p><p>CADMIUM PLATED,</p><p>MONEL SLEEVE,</p><p>BACR15FP()MP()</p><p>BACR15FP()M()R</p><p>BACR15FP()M()</p><p>BACR15FP()E()R</p><p>BACR15FP()E()</p><p>NAS1739MW</p><p>NAS1399MW()-()</p><p>NAS1399MW()-()</p><p>BACR15FP()M()R</p><p>NAS1399M()-()</p><p>NAS1739M</p><p>NAS1399MW()A()</p><p>NAS1739MW</p><p>BACR15FP()M()MONEL SLEEVE,</p><p>LOCKED SPINDLE,</p><p>SERRATED STEM,</p><p>MAX TEMP 900 ˚F</p><p>100 ˚ HEAD, FULL</p><p>MONEL SLEEVE,</p><p>CADMIUM PLATED,</p><p>LOCKED SPINDLE,</p><p>SERRATED STEM,</p><p>MAX TEMP 450 ˚F</p><p>100 ˚ HEAD, PARTIAL</p><p>NAS1399M()A()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>N97111 S0006585335_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 16 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 19</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>CHERRY SST, 5056 AL</p><p>SLEEVE, 8740 ALLOY</p><p>STEEL STEM, A-286</p><p>CRES LOCK COLLAR,</p><p>100 ˚ HEAD, NOMINAL</p><p>DIAMETER, MAX TEMP</p><p>250 ˚F.</p><p>CHERRY SST, 5056 AL</p><p>SLEEVE, 15-7 PH CRES</p><p>STEM, A-286 CRES</p><p>LOCK COLLAR, 100 ˚</p><p>HEAD, NOMINAL</p><p>DIAMETER, MAX TEMP</p><p>250 ˚F.</p><p>RIVET - BLIND - FLUSH HEAD</p><p>TABLE V</p><p>PART NUMBER ALTERNATIVEEQUIVALENTDESCRIPTION</p><p>FASTENER SUBSTITUTION</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>CR3214-()-()</p><p>NO ALTERNATIVECHERRY</p><p>CR3224-()-()</p><p>NO ALTERNATIVECHERRY</p><p>2469516 S0000577355_V1</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 17 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 20</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACR15GG()KE()</p><p>ANODIZED</p><p>7050-T73 AL, H</p><p>H</p><p>H</p><p>RIVETS - SLUG</p><p>TABLE VI</p><p>ANODIZED</p><p>BACR15BD()AD()</p><p>BACR15BD()DD()</p><p>ANODIZED</p><p>2117-T4 AL,</p><p>2024-T4 AL,</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>DESCRIPTION EQUIVALENT ALTERNATIVEPART NUMBER</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97112 S0006585336_V2</p><p>Fastener Substitution - Rivets</p><p>Figure 1 (Sheet 18 of 18)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 21</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>____</p><p>A</p><p>B</p><p>E</p><p>D</p><p>O</p><p>P</p><p>Q</p><p>N</p><p>M</p><p>L</p><p>F</p><p>G</p><p>H</p><p>I</p><p>J</p><p>K</p><p>S</p><p>T</p><p>R</p><p>C</p><p>U</p><p>USE THESE FASTENERS ONLY IF THERE IS NOT</p><p>A HEIGHT LIMIT ON THE FASTENER HEAD.</p><p>DO NOT USE CADMIUM PLATED FASTENERS AS AN</p><p>ALTERNATIVE FOR BARE OR ALUMINUM COATED</p><p>FASTENERS WHEN YOU INSTALL FASTENERS</p><p>THROUGH THE MATERIALS THAT FOLLOW:</p><p>HAVE A SLOPE OF 7 DEGREES (OR LESS) ANGLE.</p><p>THE PART WITH D-CODE (DRIVE NUT) IS</p><p>THESE COLLARS CAN BE USED ON SURFACES THAT</p><p>ALLOY STEEL FASTENERS MUST BE REPLACED WITH</p><p>THIS FASTENER IS PERMITTED FOR FASTENERS</p><p>THAT ARE 0.625 INCH OR LESS IN DIAMETER.</p><p>SUBSTITUTION IS PERMITTED FOR 0.3125 AND</p><p>0.375 DIAMETER FASTENERS ONLY.</p><p>A WASHER WITH A COUNTERBORE THAT IS</p><p>EQUIVALENT TO THE COUNTERBORE OF THE COLLAR</p><p>MUST BE USED ON THE NUT SIDE IF NUTS ARE</p><p>USED. NUTS CAN BE USED AS AN ALTERNATIVE</p><p>FOR THE HEX-DRIVE BOLT COLLARS.</p><p>THIS FASTENER IS ONLY PERMITTED IN</p><p>METAL-TO-METAL ASSEMBLIES. DO NOT USE</p><p>THESE FASTENERS IN COMPOSITE-TO-COMPOSITE</p><p>OR COMPOSITE-TO-METAL ASSEMBLIES.</p><p>THE INSTALLATION OF FASTENERS.</p><p>THE SHEAR AND TENSION TYPE FASTENERS USE</p><p>DIFFERENT TORQUE VALUES AND INSTALLATION</p><p>DO NOT USE CADMIUM PLATED FASTENERS IN</p><p>TITANIUM OR GRAPHITE (CARBON FIBER)</p><p>STRUCTURE.</p><p>DO NOT USE ALLOY STEEL FASTENERS AS AN</p><p>ALTERNATIVE FOR THE CORROSION RESISTANT</p><p>STEEL (CRES) OR TITANIUM FASTENERS IN:</p><p>AREAS WHERE ANTI-MAGNETIC FASTENERS ARE</p><p>NECESSARY</p><p>-</p><p>- GRAPHITE (CARBON FIBER) STRUCTURE</p><p>- CRES STRUCTURE</p><p>THESE BOLTS MUST HAVE A HOLE WITH A LARGER</p><p>FILLET RELIEF UNDER THE BOLT HEAD. REFER</p><p>THE CADMIUM-PLATED ALLOY STEEL</p><p>FASTENERS ARE PERMITTED AS A</p><p>STRUCTURAL ALTERNATIVE.</p><p>NOTE:</p><p>HOWEVER, AN ALLOY-STEEL FASTENER,</p><p>AND THE ADJACENT ALUMINUM STRUCTURE</p><p>TOGETHER CAN CAUSE CORROSION.</p><p>ALTERNATIVES.</p><p>REFER TO TABLE I FOR THE FASTENER</p><p>INSTALLATION.</p><p>PROTECTIVE TREATMENT FOR FASTENER</p><p>THEREFORE, THESE FASTENERS, THE</p><p>EQUIVALENT, AND THE ALTERNATIVE</p><p>MUST BE INSTALLED WET WITH THE</p><p>CORRECT SEALANT.</p><p>NOTES</p><p>BOEING RECOMMENDS THAT YOU APPLY TWO</p><p>COATS OF BMS 10-79 TYPE III PRIMER</p><p>ON THE FASTENER HEAD.</p><p>RECOMMENDED.</p><p>COATED TITANIUM, ALUMINUM PIGMENT</p><p>(BMS 10-85) COATED A286, OR CADMIUM PLATED</p><p>STRUCTURE ARE ALUMINUM PIGMENT (BMS 10-85)</p><p>THE RECOMMEND FASTENERS IN ALUMINUM</p><p>A286.</p><p>SUBSTITUTION INDEX.</p><p>REFER TO SRM 51-40-02 FOR THE REMOVAL AND</p><p>TOOLS. REFER TO SRM 51-40-04.</p><p>REFER TO SRM 51-20-01 FOR THE NECESSARY</p><p>TO SRM 51-40-05.</p><p>WHEN A PH13-8Mo CRES BOLT IS REMOVED FOR</p><p>ANY REASON, ALWAYS REPLACE THE BOLT WITH</p><p>AN ALTERNATIVE FASTENER.</p><p>THESE FASTENERS ARE PERMITTED ONLY IN CLOSE</p><p>REAM OR LARGER HOLES (NON-INTERFERENCE HOLES).</p><p>THIS FASTENER IS NOT PERMITTED IN AREAS</p><p>WHERE THE TEMPERATURE IS MORE THAN 350 ˚F</p><p>(177˚C).</p><p>THIS FASTENER IS NOT PERMITTED IN AREAS</p><p>WHERE ELECTRICAL CONDUCTIVITY IS REQUIRED</p><p>AS GIVEN IN BAC5117.</p><p>WHEN A CADMIUM PLATED TITANIUM BOLT IS</p><p>REMOVED FOR ANY REASON, ALWAYS REPLACE</p><p>THE BOLT WITH AN ALTERNATIVE FASTENER.</p><p>ASK THE BOEING COMPANY FOR FASTENER</p><p>THIS FASTENER IS NOT PERMITTED IN AREAS</p><p>WHERE THE TEMPERATURE IS MORE THAN 450 ˚F</p><p>(232˚C).</p><p>ALLOY STEEL FASTENERS WHEN YOU ATTACH A</p><p>SENSOR TARGET TO THE TARGET MOUNTING</p><p>BRACKET AT CYLINDRICAL PROXIMITY SENSOR</p><p>INSTALLATIONS.</p><p>THE FASTENER MUST BE INSTALLED WITH TORQUE</p><p>CONTROLLED TOOLING. REFER TO SRM 51-40-04.</p><p>INSTALLATION. REFER TO SRM 51-40-02.</p><p>A WASHER IS NECESSARY FOR THIS TYPE OF</p><p>WHEN A H-11 STEEL BOLT IS REMOVED FOR ANY</p><p>REASON, ALWAYS REPLACE THE BOLT WITH AN</p><p>ALTERNATIVE FASTENER.</p><p>THIS FASTENER IS NOT PERMITTED IN AREAS</p><p>WHERE THE TEMPERATURE IS MORE THAN</p><p>600 ˚F (316˚C).</p><p>- TITANIUM STRUCTURE</p><p>- GRAPHITE (CARBON FIBER) STRUCTURE.</p><p>N97113 S0006585337_V3</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 1 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 22</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>-</p><p>-</p><p>-</p><p>-</p><p>APPLICABLE ONLY FOR DIAMETERS THAT ARE</p><p>0.250 INCH AND LARGER.</p><p>THE COLLARS:</p><p>ALUMINUM COLLARS HAVE A MAXIMUM</p><p>TEMPERATURE OF 250 ˚F (171˚C)</p><p>TEMPERATURE OF 900 ˚F (482˚C)</p><p>MONEL COLLARS HAVE A MAXIMUM</p><p>TEMPERATURE OF 900 ˚F (482˚C).</p><p>WHEN YOU REMOVE ALLOY STEEL BOLTS THAT HAVE</p><p>A LAYER OF BMS 10-85 (NOT CAD PLATED)</p><p>APPLIED, ALWAYS REPLACE THEM WITH AN</p><p>ALTERNATIVE FASTENER.</p><p>THE MAXIMUM TEMPERATURE GIVEN IN THE</p><p>DESCRIPTION IS FOR THE BOLT ONLY. THE</p><p>MAXIMUM TEMPERATURE APPLICATION FOR THE</p><p>BOLT/COLLAR COMBINATION MAY BE LESS, IF</p><p>THERE ARE LIMITS PUT ON THE COLLAR.</p><p>THE FOLLOWING GUIDELINES ARE APPLICABLE TO</p><p>CADMIUM PLATED CRES COLLARS HAVE A</p><p>MAXIMUM TEMPERATURE OF 450 ˚F (232˚C)</p><p>UNPLATED CRES COLLARS HAVE A MAXIMUM</p><p>THE INITIAL OR SPECIFIED REPAIR FASTENER.</p><p>NOTES (CONTINUED)</p><p>USE THE SAME NUT OR COLLAR THAT WAS USED ON</p><p>SUBSTITUTION IS NOT PERMITTED WHERE</p><p>DIAMETER OF THE FASTENER IS 4 THRU 10.</p><p>RE-TORQUING OF THE FASTENER IS NECESSARY.</p><p>THIS SUBSTITUTION IS PERMITTED ONLY IF THEV</p><p>W</p><p>X</p><p>Y</p><p>Z</p><p>AA</p><p>N97114 S0006585338_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 2 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 23</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>49 THRU 56</p><p>35 THRU 48</p><p>65 THRU 67</p><p>62 THRU 64</p><p>60 THRU 61</p><p>57 THRU 59</p><p>TABLE XI</p><p>TABLE X</p><p>BOLT - TAPER SHANK - PROTRUDING HEAD</p><p>BOLT - BLIND - FLUSH HEAD</p><p>BOLT FASTENER SUBSTITUTION INDEX</p><p>TABLE I</p><p>30 THRU 34</p><p>25 THRU 29</p><p>13 THRU 24</p><p>4 THRU 12</p><p>TYPE OF FASTENER</p><p>BOLT - EXTERNAL WRENCHING - PROTRUDING HEAD</p><p>BOLT - HEX DRIVE - FLUSH HEAD (TENSION)</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (TENSION)</p><p>TABLE II</p><p>TABLE IX</p><p>TABLE VIII</p><p>TABLE VII</p><p>TABLE VI</p><p>TABLE V</p><p>TABLE IV</p><p>TABLE III</p><p>LOCATION OF FASTENER</p><p>SHEET</p><p>NUMBERSNUMBER</p><p>TABLE</p><p>BOLT - BLIND - PROTRUDING HEAD</p><p>BOLT - RECESS DRIVE - PROTRUDING HEAD</p><p>BOLT - RECESS DRIVE - FLUSH HEAD</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>N97115 S0006585339_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 3 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 24</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>AA</p><p>AA</p><p>AA</p><p>BACB30MB()A()SU</p><p>BACB30MB()A()U</p><p>BACC30AB()S</p><p>BACC30AB()S</p><p>BACB30FM()A()U BACC30AB()S</p><p>BACB30VN()K() I BACC30BK()</p><p>IBACB30VT()K() BACC30BQ()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>TABLE II</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>HL40DUWEST COAST</p><p>BACB30FM()A() HL440UC I BACC30AB()CBACB30MY()K()BACC30AB()CA-286 CRES,</p><p>HL440UC</p><p>HL440UC</p><p>HL440UC</p><p>HL440UC</p><p>HL440UC</p><p>HL440UC</p><p>HL40DU</p><p>HL40DU</p><p>HL40DU</p><p>HL40DU</p><p>HL40DU</p><p>HL40DU</p><p>SPS</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>AIC</p><p>LUBRICATED,</p><p>PASSIVATED,</p><p>DRY FILM</p><p>95 KSI SHEAR,</p><p>HI-SHEARBACC30AB()SA286 CRES,BACB30FM()A()SU</p><p>BACC30AG()</p><p>BACC30AB()S</p><p>BACB30VT()K()</p><p>I</p><p>I</p><p>I</p><p>I</p><p>I</p><p>I</p><p>I</p><p>BACC30BQ()</p><p>BACC30BL()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30BS()S</p><p>BACC30AB()S</p><p>BACC30BS()</p><p>BACB30VT()K()</p><p>BACB30MY()K()</p><p>BACB30MY()K()</p><p>BACB30VT()K()</p><p>BACB30MY()K()</p><p>BACB30VT()K()</p><p>BACC30M()</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>PLATED,</p><p>CADMIUM</p><p>WEST COAST</p><p>AIC</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>HUCK</p><p>SPS</p><p>HI-SHEAR</p><p>WEST COAST</p><p>HI-SHEAR</p><p>AIC</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>HUCK</p><p>SPS</p><p>HL18PB</p><p>HL18PB</p><p>HL18PB</p><p>HL18PB</p><p>HL18PB</p><p>HL18PB</p><p>HL18PB</p><p>ALTERNATIVE</p><p>BACC30M()</p><p>T</p><p>T</p><p>I</p><p>I</p><p>I</p><p>I</p><p>BACN10ZV()</p><p>BACN10YZ()</p><p>BACC30BL()</p><p>BACC30M()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30AG()</p><p>BACB30VT()K()</p><p>BACB30MY()K()</p><p>BACB30FM()A()</p><p>BACB30MY()K()</p><p>BACB30FM()A()BACC30AG()ALLOY STEEL,</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>PLATED,</p><p>CADMIUM</p><p>BACB30FM()-()</p><p>PART NUMBER</p><p>FASTENER</p><p>SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>Q</p><p>N97116 S0006585340_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 4 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 25</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>Z</p><p>ML</p><p>ML</p><p>T</p><p>T</p><p>T</p><p>T</p><p>T</p><p>T</p><p>T</p><p>AA</p><p>AA</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER ALTERNATIVE</p><p>BACB30FM()A()U BACC30AB()PBACB30MB()A()UBACC30AB()PA286 CRES, HI-SHEAR</p><p>BACC30AB()SBACC30MB()A()UBACC30AB()S</p><p>AIC</p><p>FAIRCHILD</p><p>DEUTSCH</p><p>HUCK</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>PASSIVATED,</p><p>SPS</p><p>WEST COAST</p><p>HL40</p><p>HL40</p><p>HL40</p><p>HL40</p><p>HL40</p><p>HL40</p><p>HL40</p><p>MAX TEMP</p><p>900 ˚F (482˚C)</p><p>BACC30AB()SBACB30MY()K()</p><p>BACB30MY()K()</p><p>BACC30AB()S</p><p>BACC30M()</p><p>A-286 CRES,</p><p>95 KSI SHEAR,</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>BACB30FM()AK()</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>AIC</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>HUCK</p><p>SPS</p><p>HI-SHEAR</p><p>WEST COAST</p><p>HL440AZ</p><p>HL440AZ</p><p>HL440AZ</p><p>HL440AZ</p><p>HL440AZ</p><p>HL440AZ</p><p>HL440AZ</p><p>BACC30M()</p><p>BACB30FM()-()BACC30M()ALLOY STEEL,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>BACB30FM()K()</p><p>AA</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACC30M()</p><p>BACB30MY()K() BACC30M()</p><p>BACC30BL()BACB30VT()K()</p><p>BACB30FM()AK()</p><p>BACB30FM()-()BACC30AG() BACC30AG()</p><p>BACB30MY()K() BACC30AG()</p><p>BACC30BQ()BACB30VT()K()</p><p>BACC30AG()</p><p>TABLE II</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>BACN10XJ()</p><p>BACN10XJ()</p><p>BACN10XJ()</p><p>BACN10YZ()</p><p>BACN10ZZ()D</p><p>BACN10ZZ()D</p><p>BACN10ZZ()D</p><p>BACB30FM()AK()</p><p>T</p><p>BACN10XJ()</p><p>BACC30M()</p><p>Q</p><p>N97117 S0006585341_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 5 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 26</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>T</p><p>T</p><p>I</p><p>T</p><p>I</p><p>I</p><p>I</p><p>T</p><p>I</p><p>A L</p><p>T</p><p>T</p><p>T</p><p>I</p><p>I</p><p>T</p><p>J</p><p>I</p><p>I</p><p>EQUIVALENT MATING PART</p><p>FASTENER SUBSTITUTION</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>PART NUMBER DESCRIPTION</p><p>MATING</p><p>PART</p><p>ALTERNATIVE</p><p>HI-SHEAR</p><p>FAIRCHILD</p><p>WEST COAST</p><p>HL22</p><p>HL22</p><p>NO ALTERNATIVEHL22BACC30P</p><p>AA</p><p>BACB30GZ()-()</p><p>BACB30MY()C() 6AL-4V</p><p>TITANIUM</p><p>CADMIUM PLATED,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>ANODIZED,</p><p>7075-T6 AL,</p><p>BACN10YT()CD</p><p>BACN10YT()CD</p><p>BACB30MB()AK() BACC30X()</p><p>BACN10YT()CD</p><p>BACB30AB()CBACB30FM()AK()BACC30AB()C</p><p>BACC30AB()CBACB30MY()K()</p><p>BACN10BH()</p><p>TABLE II</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>44.5 KSI SHEAR,</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>MAX TEMP</p><p>250 ˚F (121˚C)</p><p>H AA</p><p>BACC30BH()BACB30NX()K()</p><p>BACN10YT()CD</p><p>BACC30X()</p><p>BACB30VT()K() BACC30BS()</p><p>BACC30AG() BACB30FM()-() BACC30AG()</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>BACN10ZZ()D</p><p>BACB30FM()A()</p><p>BACC30AG()</p><p>BACN10ZZ()D</p><p>BACB30FM()AK()</p><p>BACB30MY()K() BACC30AG()</p><p>BACN10ZZ()D</p><p>BACB30VN()K() BACC30BK()</p><p>BACB30VT()K() BACC30BQ()</p><p>NO EQUIVALENT</p><p>N97118 S0006585342_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 6 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 27</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30MB()-()</p><p>BACB30MB()A()</p><p>BACB30GW()A()</p><p>NAS1080E</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACN10YT()CD</p><p>BACC30X()</p><p>BACC30K()</p><p>BACN10YT()CD</p><p>BACC30BH()</p><p>IBACB30FM()AK()</p><p>TBACN10ZZ()D</p><p>TBACN10YT()CD</p><p>BACN10XJ()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30AB()C</p><p>T</p><p>BACB30FM()A()</p><p>BACN10XJ()</p><p>TBACN10ZZ()D</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30AB()C</p><p>T</p><p>BACB30FM()-() LA</p><p>BACN10XJ()</p><p>BACC30AB()C</p><p>T</p><p>T</p><p>BACN10ZZ()D</p><p>BACN10YT()CD</p><p>BACC30M()</p><p>BACC30AG()</p><p>T</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>TABLE II</p><p>AAH</p><p>BACC30M()</p><p>LUBRICATED,</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>CADMIUM PLATED,</p><p>TITANIUM,</p><p>6AL-4VBACB30MY()C()</p><p>ALTERNATIVE</p><p>PART</p><p>MATING</p><p>DESCRIPTIONPART NUMBER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>NO EQUIVALENT</p><p>N97119 S0006585343_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 7 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 28</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>T</p><p>BACN10YT()CSA</p><p>H</p><p>BACN10YT()CD T</p><p>T</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACB30NX()K()</p><p>BACC30AG()</p><p>BACC30M()</p><p>T</p><p>T</p><p>BACN10XJ()</p><p>BACN10YT()CD</p><p>BACN10ZZ()D</p><p>I</p><p>BACB30VN()K() I J BACC30BK()</p><p>BACB30VT()K() I</p><p>BACN10YZ()</p><p>BACC30BL()</p><p>BACC30BQ()</p><p>BACC30AB()CBACB30MY()K() I</p><p>FASTENER SUBSTITUTION</p><p>EQUIVALENT MATING PART</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>PART NUMBER DESCRIPTION</p><p>MATING</p><p>PART</p><p>ALTERNATIVE</p><p>BACC30M()6AL-4V</p><p>CADMIUM PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30MY()C()</p><p>AA</p><p>TITANIUM,</p><p>BACB30MY()K()</p><p>AA</p><p>ALUMINUM</p><p>PIGMENTED T</p><p>HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>BACC30AG()</p><p>AIC</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>HUCK</p><p>SPSBACC30AB()S</p><p>BACC30AB()C HI-SHEAR</p><p>WEST COAST</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>LUBRICATED,</p><p>TITANIUM,</p><p>6AL-4V</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACB30FM()-()</p><p>BACB30FM()A()</p><p>BACB30VT()K()</p><p>BACB30VN()K()</p><p>BACB30FM()AK()</p><p>BACB30FM()AK()</p><p>BACB30VT()K()</p><p>BACB30NX()K()</p><p>BACB30NM()K()</p><p>BACB30MB()AK()</p><p>M</p><p>J</p><p>LA</p><p>BACN10YT()CS</p><p>BACC30AB()S</p><p>BACC30BS()</p><p>F</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>TABLE II</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>BACC30AG()</p><p>BACC30BQ()</p><p>BACC30BK()</p><p>BACN10ZZ()D</p><p>BACN10ZZ()D</p><p>T</p><p>T</p><p>T</p><p>R</p><p>BACN10GW()AS</p><p>BACC30X()S</p><p>BACC30BH()S</p><p>NAS1805-()</p><p>R</p><p>BACN10BH()S</p><p>BACC30X()S</p><p>BACC30AG()</p><p>M</p><p>NO EQUIVALENT</p><p>N97120 S0006585344_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 8 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 29</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>HL10VAZHI-SHEAR</p><p>WEST COAST HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>HL10VAZ</p><p>AIC</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>HUCK</p><p>HL10VAZSPS</p><p>6AL-4V</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TITANIUM,</p><p>BACC30AG()</p><p>BACC30AB()C</p><p>BACN10YT()CD</p><p>BACN10XJ()</p><p>BACC30M()</p><p>T</p><p>BACB30FM()-()BACC30M()</p><p>AA</p><p>BACB30MY()K()</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>T</p><p>BACCN10XJ()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30AB()C</p><p>T</p><p>MBACB30FM()A()</p><p>BACN10ZZ()D T</p><p>BACB30FM()AK() BACC30AB()C</p><p>BACN10XJ()</p><p>BACC30M()</p><p>BACC30AG()</p><p>T</p><p>BACN10ZZ()D T</p><p>BACN10YT()CD T</p><p>BACN10YT()CD T</p><p>BACN10ZZ()D T</p><p>NAS1080E</p><p>BACC30K()J MBACB30GW()A()</p><p>BACB30MB()-() BACC30BH()</p><p>BACB30VT()K()</p><p>BACB30VN()K() J</p><p>BACN10YZ()</p><p>BACC30BL()</p><p>BACC30BK()</p><p>T</p><p>BACB30NX()K() BACC30BH()</p><p>BACB30MB()A() M</p><p>BACC30X()</p><p>BACN10YT()CD</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACN10YT()CD</p><p>BACC30X()</p><p>BACN10YT()CD</p><p>T</p><p>T</p><p>T</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>TABLE II</p><p>LA M</p><p>LA M</p><p>N97121 S0006585345_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 9 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 30</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>TABLE II</p><p>FAIRCHILD</p><p>CETYL ALCOHOL</p><p>LIGHTWEIGHT,</p><p>LOCKING</p><p>SWAGE</p><p>LUBRICATED,</p><p>SHEAR,</p><p>95 KSI</p><p>AL COATED,</p><p>HST10AG</p><p>T</p><p>T</p><p>O</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>HUCK VL10AG</p><p>VL10AG</p><p>AIC</p><p>BACB30XE()K()</p><p>BACB30VT()K()</p><p>AA BACC30AG()</p><p>BACC30BK()</p><p>BACC30BK()</p><p>BACC30BK()</p><p>BACC30CG()</p><p>TITANIUM</p><p>6AL-4V</p><p>BACC30BL()BACC30CK()</p><p>BACC30BS()S</p><p>WITH</p><p>BACW10CA()CCU</p><p>AND</p><p>BACW10CA()PVU</p><p>BACN10ZV() BACN10XJ()BACB30MY()K()</p><p>J O</p><p>J O</p><p>J</p><p>6AL-4V HI-SHEAR</p><p>BACC30BS()S</p><p>BACC30BQ()</p><p>BACN10YZ()</p><p>BACC30BP()</p><p>BACN10XJ()</p><p>BACC30AG()</p><p>BACC30M()</p><p>HST10AG</p><p>HST10AG</p><p>SPS</p><p>BACC30BL()</p><p>BACC30AB()S</p><p>BACC30AB()C</p><p>LIGHTWEIGHT,</p><p>COATING,</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TITANIUM,</p><p>BACB30MY()K()</p><p>BACB30MY()K()</p><p>BACB30MY()K()</p><p>BACB30VN()K()</p><p>BACB30VN()K()</p><p>BACB30MY()K()</p><p>BACB30VN()K()</p><p>(ENLARGED</p><p>V HEX)</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>AIC</p><p>HUCK</p><p>FAIRCHILD</p><p>VL310AG</p><p>VL310AG</p><p>SPS</p><p>T</p><p>I</p><p>BACN10XJ()</p><p>600 ˚F (316˚C)</p><p>MAX TEMP</p><p>I</p><p>ALTERNATIVE</p><p>BACB30VT5HK()</p><p>AA</p><p>BACB30VT5K()6AL-4V</p><p>LIGHTWEIGHT,</p><p>COATING,</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>TITANIUM,</p><p>HI-SHEAR HST108AG</p><p>HST108AG</p><p>HST108AG</p><p>BACB30MY()R()</p><p>AA</p><p>BACC30AG()</p><p>BACC30M()BACB30MY()K()</p><p>BACB30MY()K()6AL-4V</p><p>TITANIUM,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>PHOSPHATE</p><p>FLUORIDE</p><p>COATED,</p><p>SPS</p><p>HUCK</p><p>AIC</p><p>FAIRCHILD</p><p>DEUTSCH</p><p>WEST COAST</p><p>BACC30AG()</p><p>BACC30M()</p><p>HI-SHEAR</p><p>HL10VRA</p><p>HL10VRA</p><p>HL10VRA</p><p>HL10VRA</p><p>HL10VRA</p><p>HL10VRA</p><p>HL10VRA</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACC30CH()</p><p>BACB30VT()K()</p><p>BACB30VT()K()</p><p>BACC30BS()S</p><p>BACB30VT()K()</p><p>NO EQUIVALENT</p><p>N97122 S0006585346_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 10 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 31</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>I</p><p>HLT620AP-()-()</p><p>HLT620-()-()</p><p>HLT420-()-()</p><p>HLT420AP-()-()</p><p>HLT420PB-()-() BACB30YL()K()</p><p>NICKEL</p><p>ALLOY 718,</p><p>1/64 OVERSIZE,</p><p>125 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>NICKEL</p><p>ALLOY 718,</p><p>1/64 OVERSIZE,</p><p>125 KSI SHEAR,</p><p>PASSIVATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>NICKEL</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>PASSIVATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>NICKEL</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>NICKEL</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>CADMIUM</p><p>PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>BACB30YL()K()X</p><p>BACB30YL()U()X</p><p>BACB30YL()U()</p><p>BACB30YL()K()</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>MATING</p><p>PART</p><p>DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>TABLE II</p><p>SPS HLT420AP</p><p>AIC HLT420AP</p><p>HI-SHEAR HLT420APBACB30YL()K() BACC30CQ()CNICKEL</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>350 ˚F (177˚C)</p><p>HLT420AP HL791BFBACC30CQ()S</p><p>HLT420AP HL791RD</p><p>N97123 S0006585347_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 11 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 32</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>INICKEL BACB30YL()K()X</p><p>LUBRICATED</p><p>PLATED,</p><p>CADMIUM</p><p>125 KSI SHEAR,</p><p>1/64 OVERSIZE,</p><p>CETYL ALCOHOL</p><p>ALLOY 718,</p><p>HLT620PB-()-()</p><p>G</p><p>TABLE II</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (SHEAR)</p><p>I</p><p>HL860AP-()-()</p><p>HL644AP-()-()</p><p>HLT714-()-()</p><p>HLT714AP-()-()</p><p>HLT714PB-()-()</p><p>LUBRICATED</p><p>PH13-8 Mo</p><p>APPLICATIONS,</p><p>CETYL ETHYL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>COMPOSITE</p><p>TITANIUM</p><p>TITANIUM,</p><p>6AL-4V</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>STEEL,</p><p>STAINLESS</p><p>CETYL ALCOHOL</p><p>ALLOY 718,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>1/32 OVERSIZE,</p><p>125 KSI SHEAR,</p><p>PASSIVATED</p><p>NICKEL</p><p>ALLOY 718,</p><p>1/32 OVERSIZE,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>125 KSI SHEAR,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>NICKEL</p><p>ALLOY 718,</p><p>1/32 OVERSIZE,</p><p>LUBRICATED</p><p>125 KSI SHEAR,</p><p>CADMIUM</p><p>PLATED,</p><p>NICKEL</p><p>HLT420AP-()-()</p><p>BACB30VG()K()</p><p>BACB30YL()U()Y</p><p>BACB30YL()K()Y</p><p>BACB30YL()K()Y</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97124 S0006585348_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 12 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 33</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30YP()K() I BACC30BS()</p><p>IBACB30VU()K() BACC30BS()</p><p>BACC30BL()</p><p>BACC30BQ()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>LUBRICATED</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>BACB30YP()K() I BACC30BL()</p><p>TBACN10YZ()</p><p>TBACN10YZ()</p><p>BACC30M()</p><p>BACB30VU()K()</p><p>BACB30NW()K()</p><p>BACB30VU()K()</p><p>BACC30BL()</p><p>BACC30BQ()</p><p>I</p><p>I</p><p>I</p><p>BACC30M()</p><p>BACB30YP()K() I BACC30BQ()</p><p>IBACB30NW()K() BACC30AG()BACC30AG()</p><p>IBACB30VU()K() BACC30BS()S</p><p>BACC30BS()SBACB30YP()K() I</p><p>IBACB30NW()K() BACC30AB()SBACC30AB()S</p><p>IBACB30NW()K() BACC30AB()CBACB30FN()A() AA A286 CRES,</p><p>100 ˚ HEAD,</p><p>CADMIUM</p><p>PLATED,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>BACC30AB()C</p><p>WEST COAST</p><p>HL441UCHI-SHEAR</p><p>SPS</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>AIC</p><p>HL441UC</p><p>HL441UC</p><p>HL441UC</p><p>HL441UC</p><p>HL441UC</p><p>HL441UC</p><p>TBACN10ZV()</p><p>T</p><p>T</p><p>BACN10ZV()</p><p>BACC30BL()</p><p>BACN10YZ()</p><p>BACB30YP()K() I</p><p>BACB30YP()K() I</p><p>BACB30VU()K() I BACC30BQ()</p><p>BACB30FN()A() BACC30M()</p><p>I</p><p>IBACB30NW()K()</p><p>BACB30VU()K()</p><p>BACC30M()</p><p>BACC30M()</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>LUBRICATED</p><p>AAQ</p><p>ALTERNATIVE</p><p>HL19PB</p><p>HL19PB</p><p>HL19PB</p><p>HL19PB</p><p>HL19PB</p><p>HL19PB</p><p>HL19PB</p><p>WEST COAST</p><p>IBACB30NW()K()</p><p>BACB30FN()A()</p><p>100 ˚ HEAD,</p><p>CADMIUM</p><p>PLATED,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>ALLOY STEEL,BACB30FN()-()</p><p>BACC30AG()SPS</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>AIC</p><p>BACC30AG()HI-SHEARBACC30AG()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>TBACN10YZ()</p><p>N97125 S0006585349_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 13 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 34</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACC30AB()S</p><p>BACC30AB()S</p><p>BACC30AB()P</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>HL41</p><p>HL41</p><p>HI-SHEAR</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>WEST COAST</p><p>SPS</p><p>AIC</p><p>HL41</p><p>HL41</p><p>HL41</p><p>HL41</p><p>HL41</p><p>BACB30FN()A()U</p><p>BACB30FN()A()SU</p><p>AA</p><p>HL41DU BACC30AB()SBACB30FN()A()UHI-SHEARA286 CRES,</p><p>HL41DU</p><p>HL41DU</p><p>HL41DU</p><p>HL41DU</p><p>HL41DU</p><p>HL41DU</p><p>A286 CRES, NO ALTERNATIVE</p><p>AIC</p><p>FAIRCHILD</p><p>SPS</p><p>DRY FILM</p><p>LUBRICATED,</p><p>100 ˚ HEAD</p><p>PASSIVATED,</p><p>95 KSI SHEAR,</p><p>HUCK</p><p>DEUTSCH</p><p>WEST COAST</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>100 ˚ HEAD</p><p>PASSIVATED,</p><p>95 KSI SHEAR,</p><p>BACB30YP()K() BACC30BS()S</p><p>BACB30VU()K() BACC30BS()S</p><p>BACB30NW()K() BACC30AB()SBACC30AB()S</p><p>BACB30YP()K() BACC30BS()</p><p>BACB30VU()K() BACC30BS()</p><p>BACB30NW()K() BACC30AB()C</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>LUBRICATED</p><p>SPS</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>AIC</p><p>100 ˚ HEAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>HL441AZ</p><p>HL441AZ</p><p>HL441AZ</p><p>HL441AZ</p><p>HL441AZ</p><p>WEST COAST</p><p>WEST COAST</p><p>AIC</p><p>HL441AZ</p><p>WC131</p><p>L-839C</p><p>AA</p><p>HI-SHEARA286 CRES, BACC30AB()C HL441AZBACB30FN()AK()</p><p>ALTERNATIVE</p><p>INITIAL FASTENER OR SPECIFIED</p><p>MATING PART</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>EQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>N97126 S0006585350_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 14 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 35</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>T</p><p>T</p><p>M</p><p>T</p><p>T</p><p>Q</p><p>M</p><p>T</p><p>T</p><p>I</p><p>I</p><p>Z</p><p>Q</p><p>250 ˚F (121˚C)</p><p>MAX TEMP</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>250 ˚F (121˚C)</p><p>MAX TEMP</p><p>FAIRCHILD</p><p>WESTCOAST</p><p>LUBRICATED,</p><p>SHEAR,</p><p>44.5 KSI</p><p>ANODIZED,</p><p>CETYL ALCOHOL</p><p>100 ˚ REDUCED</p><p>SHEAR HEAD,</p><p>NO ALTERNATIVEHI-SHEAR7075-T6 AL,AA BACC30P()R</p><p>AA</p><p>LUBRICATED,</p><p>SHEAR,</p><p>44.5 KSI</p><p>ANODIZED,</p><p>CETYL ALCOHOL</p><p>100 ˚ HEAD,</p><p>7075-T6 AL, BACC30P() NO ALTERNATIVE</p><p>FAIRCHILD</p><p>WESTCOAST</p><p>HI-SHEAR</p><p>HL23</p><p>HL23</p><p>HL23</p><p>HL505</p><p>HL505</p><p>HL505BACB30HA()R()</p><p>BACB30HA()-()</p><p>REPAIR FASTENER</p><p>MATING</p><p>PART NUMBER MATING PARTALTERNATIVEEQUIVALENTDESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>FASTENER SUBSTITUTION</p><p>PART</p><p>BACB30ND()A()HI-SHEAR HL525</p><p>SPS HL525</p><p>HUCK HL525</p><p>DEUTSCH HL525</p><p>FAIRCHILD HL525</p><p>WEST COAST HL525</p><p>ALLOY STEEL,</p><p>CADMIUM PLATED</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>100 ˚ (MS20426)</p><p>HEAD, MAX TEMP</p><p>450 ˚F (232˚C)</p><p>AA</p><p>BACC30AG()BACB30ND()-()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30AG()</p><p>BACN10ZZ()D</p><p>BACB30NZ()K()</p><p>BACB30ND()A()</p><p>BACB30NZ()K()</p><p>BACC30M()</p><p>BACC30M()</p><p>BACN10ZZ()D</p><p>BACN10YZ()</p><p>BACN10YZ()</p><p>BACC30BQ()</p><p>BACC30BL()</p><p>BACC30M()</p><p>BACC30M()</p><p>BACC30BQ()</p><p>BACC30AG()</p><p>BACC30AG()</p><p>BACC30BL()</p><p>BACB30VU()K()</p><p>BACB30NW()K()</p><p>BACB30FN()A()</p><p>BACB30YP()K()</p><p>BACB30VU()K()</p><p>BACB30NW()K()</p><p>BACB30FN()A()</p><p>BACB30YP()K()</p><p>BACN10ZV()</p><p>BACN10ZV()</p><p>BACC30M()</p><p>BACC30AG()BACB30FN()K()</p><p>350 ˚F (177˚C)</p><p>MAX TEMP</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>AL COATED,</p><p>ALLOY STEEL, NO EQUIVALENT</p><p>N97127 S0006585351_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 15 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 36</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACC30M() A LBACB30ND()-()</p><p>BACB30NZ()K()</p><p>BACC30M()</p><p>I BACC30M()</p><p>BACC30AG()</p><p>T</p><p>BACB30ND()-() BACC30AG()A L</p><p>T</p><p>BACB30NZ()K()</p><p>BACN10ZZ()D</p><p>BACN10ZZ()D</p><p>BACC30AG()I</p><p>900 ˚F (482˚C)</p><p>HEAD, MAX TEMP</p><p>450 ˚F (232˚C)</p><p>HEAD, MAX TEMP</p><p>BACB30ND()A()U</p><p>AA</p><p>BACB30ND()A()</p><p>CADMIUM</p><p>PLATED,</p><p>LUBRICATED,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>100 ˚ (MS20426)</p><p>A286 CRES,</p><p>PASSIVATED,</p><p>LUBRICATED,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>100 ˚ (MS20426)</p><p>BACC30AB()P</p><p>WEST COAST HL445</p><p>HI-SHEAR HL445</p><p>FAIRCHILD</p><p>DEUTSCH</p><p>HUCK</p><p>SPS</p><p>HL445</p><p>HL445</p><p>HL445</p><p>HL445</p><p>NO ALTERNATIVE</p><p>AA</p><p>HL445PB</p><p>HL445PB</p><p>HL445PB</p><p>HL445PB</p><p>HL445PB</p><p>HL445PBA286 CRES, HI-SHEAR</p><p>WEST COAST</p><p>FAIRCHILD</p><p>DEUTSCH</p><p>HUCK</p><p>SPS</p><p>H</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>BACC30AB()C BACB30FN()-() ABACB30NW()C()</p><p>ALTERNATIVE</p><p>L6AL-4V</p><p>TITANIUM,</p><p>100 ˚ REDUCED</p><p>HEAD,</p><p>CADMIUM PLATED,</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>BACB30FN()A()</p><p>T</p><p>BACC30AB()C</p><p>BACN10YT()CD</p><p>T</p><p>BACC30AB()C</p><p>BACN10YT()CD</p><p>BACC30AB()CBACB30FN()AK() I</p><p>BACC30BS()IBACB30VU()K()</p><p>BACC30AG()</p><p>BACC30BS()IBACB30YP()K()</p><p>TBACN10YT()CD</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>T</p><p>BACB30FN()A()</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>T</p><p>IBACB30FN()AK()</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>T</p><p>IBACB30NW()K()</p><p>BACC30BE()BACB30TY()K() I J</p><p>BACC30BK()I JBACB30VM()K()</p><p>BACC30BQ()IBACB30VU()K()</p><p>TBACN10ZZ()D</p><p>BACC30AG()BACB30FN()-()</p><p>BACC30BQ()IBACB30YP()K()</p><p>TABLE III</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>AA</p><p>LA</p><p>NO EQUIVALENT</p><p>N97128 S0006585352_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 16 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 37</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30FN()-() BACC30AG()</p><p>BACC30M()</p><p>BACC30AB()CBACB30FN()A()</p><p>BACC30AB()C</p><p>T</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACN10XJ()</p><p>BACN10YT()CD T</p><p>TBACN10ZZ()D</p><p>T</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACN10XJ()</p><p>BACN10YT()CD T</p><p>TBACN10ZZ()D</p><p>IBACB30FN()AK()</p><p>LA</p><p>H</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>TBACN10YZ()</p><p>T</p><p>BACB30VU()K() I BACC30BL()</p><p>BACN10YZ()</p><p>BACB30YP()K() I BACC30BL()</p><p>TBACN10ZZ()D</p><p>BACB30VM()K() JI BACC30BK()</p><p>JIBACB30TY()K() BACC30BE()</p><p>BACC30AG()BACB30NW()K()</p><p>BACC30M()</p><p>LUBRICATED,</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>CETYL ALCOHOL</p><p>CADMIUM PLATED,</p><p>95 KSI SHEAR,</p><p>HEAD,</p><p>100 ˚ REDUCED</p><p>TITANIUM,</p><p>6AL-4V</p><p>ALTERNATIVE</p><p>BACB30NW()C()</p><p>I</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>AA</p><p>NO EQUIVALENT</p><p>N97129 S0006585353_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 17 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 38</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>M</p><p>ABACB30FN()-()</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>HEAD,</p><p>100˚ REDUCED</p><p>95 KSI SHEAR,</p><p>LUBRICATED</p><p>ALCOHOL</p><p>CETYL</p><p>TITANIUM,</p><p>6AL-4V</p><p>AA</p><p>BACB30NW()K() HI-SHEAR</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HL11VAZ</p><p>SPS</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>WEST COAST</p><p>AIC HL11VAZ</p><p>BACC30AB()C HL11VAZ BACC30AB()C</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION ALTERNATIVE</p><p>L</p><p>BACC30AB()C</p><p>BACN10YT()CD</p><p>MBACB30FN()A()</p><p>BACN10YT()CD T</p><p>T</p><p>BACC30AB()C</p><p>BACN10YT()CD</p><p>BACB30FN()AK()</p><p>T</p><p>BACC30BS()</p><p>BACC30BS()</p><p>BACC30AG()</p><p>BACN10ZZ()D</p><p>BACC30BS()S</p><p>BACB30VU()K()</p><p>BACB30YP()K()</p><p>T</p><p>BACB30FN()-()</p><p>BACB30VU()K()</p><p>BACB30YP()K()</p><p>BACC30AB()S</p><p>BACC30AG()</p><p>M</p><p>BACC30BE()</p><p>BACC30BK()</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>J</p><p>J</p><p>BACC30BQ()</p><p>BACC30BQ()</p><p>BACN10XJ()</p><p>BACC30AB()C</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30M()</p><p>M</p><p>BACB30TY()K()</p><p>BACB30VM()K()</p><p>BACB30FN()A()</p><p>BACB30FN()AK()</p><p>BACB30VU()K()</p><p>BACB30YP()K()</p><p>BACB30FN()-()</p><p>BACB30FN()A()</p><p>T</p><p>T</p><p>T</p><p>BACB30FN()AK()</p><p>T</p><p>TBACN10ZZ()D</p><p>BACC30AB()C</p><p>BACC30AG()</p><p>BACC30M()</p><p>BACN10XJ()</p><p>BACN10YT()CD</p><p>BACN10YT()CD T</p><p>T</p><p>BACN10ZZ()D T</p><p>TABLE III</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>BACC30M()</p><p>BACC30BS()S</p><p>BACC30AG()</p><p>LA M</p><p>LA M</p><p>N97130 S0006585354_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 18 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 39</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACC30M()BACB30ND()-() A L</p><p>BACB30ND()-() LA BACC30AG()</p><p>BACN10ZZ()D T</p><p>H</p><p>BACC30M()</p><p>BACC30M()</p><p>BACC30BS()S</p><p>450 ˚F (232˚C)</p><p>HEAD, MAX TEMP</p><p>T</p><p>T</p><p>BACN10YZ()</p><p>BACC30BL()BACB30YP()K()</p><p>BACB30YP()K() BACC30BQ()</p><p>BACN10YZ()</p><p>WBACC30BS()</p><p>BACC30M() BACB30VU()K() BACC30BL()</p><p>BACB30YP()K() W</p><p>IBACB30VU()K() BACC30BQ()BACC30AG() HL11VRAHI-SHEAR</p><p>HL11VRA</p><p>HL11VRA</p><p>HL11VRA</p><p>HL11VRA</p><p>HL11VRA</p><p>SPS</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>AIC</p><p>WEST COAST HL11VRA</p><p>95 KSI SHEAR,</p><p>100 ˚ (MS20426)</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>CAD PLATED</p><p>TITANIUM,</p><p>6AL-4V</p><p>6AL-4V</p><p>HEAD,</p><p>PHOSPHATE</p><p>FLUORIDE</p><p>COATED,</p><p>100 ˚ REDUCED</p><p>95 KSI SHEAR,</p><p>SOLID FILM</p><p>TITANIUM,</p><p>LUBRICATED</p><p>LUBRICATED</p><p>6AL-4V</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>100 ˚ REDUCED</p><p>HEAD,</p><p>COATED,</p><p>FLUORIDE</p><p>PHOSPHATE</p><p>TITANIUM,</p><p>BACB30NZ()C()</p><p>BACB30NW()S()</p><p>AA</p><p>AA</p><p>BACB30NW()R()</p><p>AA</p><p>BACB30NZ()K()</p><p>BACB30ND()A()</p><p>BACB30NZ()K()</p><p>BACB30NZ()K()</p><p>BACB30ND()A()</p><p>BACB30ND()A()</p><p>BACB30VU()S()</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>I BACC30AB()C</p><p>BACC30AB()C</p><p>I BACC30AG()</p><p>I</p><p>BACC30AG()</p><p>BACN10ZZ()D T</p><p>BACC30BS()S</p><p>BACC30AG()</p><p>BACC30M()</p><p>BACC30AB()S HL11VSYHI-SHEAR</p><p>HL11VSY</p><p>HL11VSY</p><p>HL11VSY</p><p>HL11VSY</p><p>AIC HL11VSY</p><p>WEST COAST HL11VSY</p><p>SPS</p><p>HUCK</p><p>DEUTSCH</p><p>FAIRCHILD</p><p>BACC30AB()C</p><p>BACN10YT()CD</p><p>BACB30YP()K()</p><p>W</p><p>BACB30VU()K() BACC30BL()</p><p>BACB30VU()K() WBACC30BS()</p><p>J</p><p>ALTERNATIVE</p><p>BACB30TY()K()</p><p>BACN10YT()CS</p><p>T</p><p>JBACB30VM()K()</p><p>BACB30VU()K()</p><p>BACC30M()</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>HEAD,</p><p>100 ˚ REDUCED</p><p>95 KSI SHEAR,</p><p>TITANIUM,</p><p>LUBRICATED</p><p>6AL-4V</p><p>AA</p><p>BACB30NW()K()</p><p>WEST COAST</p><p>AIC</p><p>FAIRCHILD</p><p>DEUTSCH</p><p>HUCK</p><p>SPS</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HL11VAZ</p><p>HI-SHEAR HL11VAZ</p><p>BACC30BK()</p><p>BACC30BE()</p><p>BACN10YZ()</p><p>BACC30BS()S</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>I</p><p>I</p><p>I</p><p>BACN10ZZ()D T</p><p>NO EQUIVALENT</p><p>N97131 S0006585355_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 19 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 40</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>ALCOHOL</p><p>AIC</p><p>(ENLARGED</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>LIGHTWEIGHT,</p><p>95 KSI SHEAR,</p><p>COATING,</p><p>PIGMENTED</p><p>HEAD,</p><p>100 ˚ REDUCED</p><p>TITANIUM,</p><p>ALUMINUM</p><p>HST109AG</p><p>HST109AG</p><p>SPS</p><p>BACB30VU5K()6AL-4V HST109AGHI-SHEAR</p><p>INTERNAL HEX)</p><p>HST11AG</p><p>HST11AG</p><p>SPS BACB30VM()K()</p><p>BACB30XT()K()</p><p>BACC30BK()</p><p>BACC30BK()</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>HEAD,</p><p>100 ˚ REDUCED</p><p>CETYL</p><p>LIGHTWEIGHT,</p><p>TITANIUM,</p><p>95 KSI SHEAR,</p><p>AIC</p><p>VL11AGFAIRCHILD</p><p>J O</p><p>OJ</p><p>HST11AGHI-SHEARBACC30BL()6AL-4VBACB30VU()K()</p><p>AA</p><p>BACB30NW()K() BACC30M()</p><p>AA</p><p>BACB30VU5HK()</p><p>LUBRICATED</p><p>AA M</p><p>PIGMENTED</p><p>ALUMINUM</p><p>100 ˚ (MS20426)</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>LUBRICATED,</p><p>COATING</p><p>TITANIUM,</p><p>6AL-4V BACC30M()</p><p>BACC30M()</p><p>BACC30AG()</p><p>BACC30M()BACB30ND()A()</p><p>BACC30AG()BACB30ND()A()</p><p>BACC30AG()</p><p>BACN10ZZ()D</p><p>BACN10ZZ()D</p><p>BACB30ND()-()</p><p>BACB30ND()-()</p><p>M</p><p>T</p><p>T</p><p>BACC30AB()CBACB30ND()A()BACC30AB()C M</p><p>BACB30NZ()K() HI-SHEAR</p><p>SPS HL523AZ</p><p>HUCK HL523AZ</p><p>DEUTSCH HL523AZ</p><p>FAIRCHILD HL523AZ</p><p>HL523AZ</p><p>HL523AZ</p><p>ALTERNATIVE</p><p>HUCK VL11AG</p><p>WEST COAST</p><p>HL523AZAIC</p><p>TABLE III</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>HEAD, MAX TEMP</p><p>350 ˚F (177˚C)</p><p>BACC30BP() BACB30VM()K()</p><p>BACB30XT()K()</p><p>BACB30YP()K() BACC30BL()</p><p>BACC30BK()</p><p>BACC30BK()</p><p>J O</p><p>J O</p><p>BACC30BQ()</p><p>BACC30BP()</p><p>BACC30AG()</p><p>BACC30BK()</p><p>TBACN10ZZ()D</p><p>BACB30YP()K()</p><p>BACB30NW()K()</p><p>BACB30VM()K()</p><p>BACC30BK()BACB30XT()K()</p><p>BACC30BQ()</p><p>BACC30BS()</p><p>BACC30BS()S</p><p>BACN10YT()CD</p><p>BACN10YT()CD</p><p>BACB30YP()K()</p><p>BACB30YP()K()</p><p>BACB30YP()K()</p><p>BACC30NW()K() T</p><p>TBACB30NW()K()</p><p>BACC30BS()S</p><p>BACC30BS()</p><p>BACN10YZ()</p><p>BACN10ZV()</p><p>LA M</p><p>LA M</p><p>N97132 S0006585356_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 20 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 41</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY</p><p>- See title page for details</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>REPAIR FASTENER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>HL791RDBACC30CQ()C</p><p>125 KSI SHEAR,</p><p>SHEAR HEAD</p><p>100 ˚ REDUCED</p><p>ALLOY 718,</p><p>NICKELBACB30YN()K() HLT421APHI-SHEAR</p><p>HLT421APAIC</p><p>BACB30YP()K() 6AL-4V</p><p>100 ˚ REDUCED</p><p>TITANIUM,</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>LUBRICATED</p><p>ALCOHOL</p><p>CETYL</p><p>LIGHTWEIGHT,</p><p>95 KSI SHEAR,</p><p>SHEAR DOME</p><p>HEAD,</p><p>VL18</p><p>VL331</p><p>AIR</p><p>INDUSTRIES HST331</p><p>FAIRCHILD</p><p>HI-SHEAR</p><p>HUCK</p><p>HST331</p><p>BACB30NW()K() BACC30M()</p><p>BACB30VM()K()</p><p>BACB30XT()K()</p><p>BACC30BK()</p><p>BACC30BK()</p><p>BACB30VU()K()</p><p>BACN10YZ()</p><p>BACN10XJ()</p><p>BACC30BL()</p><p>BACC30BK()</p><p>BACC30BK()</p><p>BACB30VM()K()</p><p>BACB30XT()K()</p><p>BACC30BL()</p><p>HL791BFBACC30CQ()S</p><p>BACC30BP()</p><p>BACC30BP()BACB30VU()K()</p><p>TABLE III</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>HLT421AP</p><p>HLT421AP</p><p>BACB30XG()K() 6AL-4V</p><p>100 DEGREES</p><p>TITANIUM,</p><p>SHEAR</p><p>95 KSI</p><p>AL COATED</p><p>LUBRICATED,</p><p>SWAGE</p><p>LOCKING</p><p>ALCOHOL</p><p>CETYL</p><p>LIGHTWEIGHT,</p><p>(MS20426)</p><p>HEAD,</p><p>BACB30NZ()K() BACC30AB()S</p><p>BACB30NZ()K() BACC30AB()S</p><p>WITH</p><p>BACW10CA()CCU</p><p>AND</p><p>BACW10CA()PVU</p><p>BACN10YR()CM</p><p>BACC30M()</p><p>BACN10YR()CD</p><p>BACB30NZ()K()</p><p>BACC30CG()</p><p>BACC30CK()</p><p>BACC30CH()</p><p>BACB30XR()K() 6AL-4V</p><p>130 DEGREES</p><p>TITANIUM,</p><p>AL COATED</p><p>LUBRICATED,</p><p>SWAGE</p><p>LOCKING</p><p>ALCOHOL</p><p>CETYL</p><p>LIGHTWEIGHT,</p><p>SHEAR HEAD,</p><p>BACB30WM()K() BACC30BS()S</p><p>BACB30WM()K() BACC30BU()PW</p><p>BACN10YR()CM</p><p>BACC30CG()</p><p>BACC30CH()</p><p>BACN10YR()CM</p><p>WITH</p><p>BACW10CA()CCU</p><p>AND</p><p>BACW10CA()PVU</p><p>D S</p><p>D</p><p>D</p><p>AA</p><p>OJ</p><p>J O</p><p>T</p><p>T</p><p>J O</p><p>J O</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97133 S0006585357_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 21 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 42</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>J</p><p>J</p><p>T</p><p>T</p><p>AA</p><p>AA</p><p>AA</p><p>AA</p><p>I</p><p>6AL-4V</p><p>TITANIUM,</p><p>100 ˚ REDUCED</p><p>SHEAR DOME</p><p>HEAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>95 KSI SHEAR,</p><p>LIGHTWEIGHT,</p><p>CETYL</p><p>ALCOHOL</p><p>LUBRICATED</p><p>NO ALTERNATIVE</p><p>BACC30BK()</p><p>BACC30BK()</p><p>BACB30VM()K()</p><p>BACB30XT()K()</p><p>BACC30BQ()</p><p>BACC30BS()</p><p>BACB30VU()K()</p><p>BACB30VU()K()</p><p>BACC30BS()SBACB30VU()K()BACC30BS()S</p><p>BACC30BS()</p><p>BACN10YT()CDBACC30NW()K()BACN10YZ()</p><p>BACN10ZV() BACB30NW()K() BACN10YT()CD</p><p>BACB30YN()U()NICKEL</p><p>ALLOY 718,</p><p>125 KSI</p><p>SHEAR,</p><p>100 ˚ HEAD,</p><p>GRIT BLAST</p><p>TOP OF HEAD,</p><p>PASSIVATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>HLT421-()-()</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>BACB30YP()K()</p><p>BACB30YN()K()</p><p>BACB30YN()K()</p><p>NICKEL</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>100 ˚ HEAD,</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>NICKEL</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>100 ˚ HEAD,</p><p>CADMIUM</p><p>PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>HLT421PB-()-()</p><p>HLT421AP-()-() NO ALTERNATIVE</p><p>DESCRIPTION</p><p>MATING</p><p>PART</p><p>EQUIVALENT ALTERNATIVE MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACB30NW()K()BACC30BQ()</p><p>BACN10ZZ()D</p><p>BACC30AG()</p><p>N97134 S0006585358_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 22 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 43</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>BACB30YN()K()X</p><p>BACB30YN()K()X</p><p>LUBRICATED</p><p>CETYL ALCOHOL</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>100 ˚ HEAD,</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>1/64 OVERSIZE,</p><p>NICKEL</p><p>NICKEL</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>1/64 OVERSIZE,</p><p>100 ˚ HEAD,</p><p>CADMIUM</p><p>PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>HLT621AP-()-()</p><p>HLT621PB-()-() I</p><p>NO ALTERNATIVE</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>HLT715AP-()-()</p><p>HLT715-()-()</p><p>COATING,</p><p>PIGMENTED</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>ALUMINUM</p><p>NICKEL</p><p>100 ˚ HEAD,</p><p>1/32 OVERSIZE,</p><p>125 KSI SHEAR,</p><p>ALLOY 718,</p><p>LUBRICATED</p><p>PASSIVATED,</p><p>CETYL ALCOHOL</p><p>1/32 OVERSIZE,</p><p>NICKEL</p><p>125 KSI SHEAR,</p><p>ALLOY 718,</p><p>100 ˚ HEAD,</p><p>BACB30YN()K()Y</p><p>BACB30YN()U()Y</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>BACB30YN()U()X</p><p>CETYL ALCOHOL</p><p>PASSIVATED</p><p>100 ˚ HEAD,</p><p>ALLOY 718,</p><p>125 KSI SHEAR,</p><p>1/64 OVERSIZE,</p><p>NICKEL</p><p>LUBRICATED</p><p>HLT621-()-() NO ALTERNATIVE</p><p>NO EQUIVALENT</p><p>N97135 S0006585359_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 23 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 44</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>G</p><p>G</p><p>HLT421AP-()-()</p><p>HLT421AP-()-()</p><p>BACB30YN()K()</p><p>BACB30YN()K()</p><p>I</p><p>I</p><p>HL645PB-()-()</p><p>HL645AP-()-()</p><p>PH13-8 Mo</p><p>HEAD, CADMIUM</p><p>STAINLESS</p><p>STEEL,</p><p>100 ˚ FLUSH</p><p>PLATED,</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>LUBRICATED</p><p>HEAD, ALUMINUM</p><p>CETYL ALCOHOL</p><p>PIGMENTED</p><p>COATING,</p><p>STEEL,</p><p>STAINLESS</p><p>100 ˚ FLUSH</p><p>PH13-8 Mo</p><p>G</p><p>HLT421AP-()-()</p><p>BACB30YN()K()</p><p>I</p><p>I</p><p>COATING,</p><p>PIGMENTED</p><p>ALUMINUM</p><p>CETYL ALCOHOL</p><p>LUBRICATED</p><p>BOLT - HEX DRIVE - FLUSH HEAD (SHEAR)</p><p>TABLE III</p><p>HL859AZ-()-()</p><p>HL645TB-()-()</p><p>HL859AP-()-() HL97</p><p>TITANIUM,</p><p>156 ˚ FLUSH</p><p>3.5D HEAD,</p><p>TITANIUM</p><p>COMPOSITE</p><p>APPLICATIONS,</p><p>6AL-4V</p><p>LUBRICATED</p><p>SOLID FILM,</p><p>STEEL,</p><p>STAINLESS</p><p>100 ˚ FLUSH</p><p>HEAD,</p><p>CETYL ALCOHOL</p><p>PH13-8 Mo</p><p>HL97</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTALTERNATIVEEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>IHLT715PB-()-()</p><p>LUBRICATED</p><p>NICKEL</p><p>100 ˚ HEAD,</p><p>1/32 OVERSIZE,</p><p>125 KSI SHEAR,</p><p>ALLOY 718,</p><p>PLATED,</p><p>CADMIUM</p><p>CETYL ALCOHOL</p><p>BACB30YN()K()YNO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>NO EQUIVALENT</p><p>N97136 S0006585360_V2</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 24 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 45</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>I</p><p>IBACB30NX()K()</p><p>BACB30MB()A()</p><p>BACB30MB()A()</p><p>BACB30NX()K()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>BACC30BH()P</p><p>BACC30X()P</p><p>BACC30X()P</p><p>BACC30BH()P</p><p>OR</p><p>BACB30NX()-()</p><p>T</p><p>BACN10YT()CSA</p><p>BACC30X()S</p><p>BACC30BH()S</p><p>OR</p><p>BACB30NX()-()</p><p>T</p><p>BACN10YT()CSA</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACN10XJ() T</p><p>BACC30M()</p><p>BACN10XJ()</p><p>BACC30M()</p><p>T</p><p>OR</p><p>900 ˚F (482˚C)</p><p>MAX TEMP</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>BACB30MB()A()U AA</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (TENSION)</p><p>TABLE IV</p><p>HUCK</p><p>WEST COAST</p><p>AIC</p><p>FAIRCHILD</p><p>HL448</p><p>HL448</p><p>HL448</p><p>HL448</p><p>SPS</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>PASSIVATED</p><p>A286 CRES,</p><p>95 KSI SHEAR,</p><p>160 KSI</p><p>TENSION,</p><p>HL448</p><p>HL448HI-SHEAR</p><p>450 ˚F (232˚C)</p><p>MAX TEMP</p><p>T</p><p>T</p><p>OR</p><p>BACN10YT()CDHUCK</p><p>HL448UCWEST COAST</p><p>AIC</p><p>FAIRCHILD</p><p>HL448UC</p><p>HL448UC</p><p>HL448UC</p><p>SPS</p><p>BACB30NX()K() I</p><p>HL448UC</p><p>HI-SHEAR HL448UC</p><p>PLATED,</p><p>CADMIUM</p><p>CETYL ALCOHOL</p><p>LUBRICATED,</p><p>A286 CRES,</p><p>95 KSI SHEAR,</p><p>160 KSI</p><p>TENSION,</p><p>BACB30MB()A() AA</p><p>BACN10YT()CD</p><p>AA</p><p>HL1050PB</p><p>HL1050PB</p><p>HL1050PB</p><p>HL1050PB</p><p>HL1050PB</p><p>HL1050PB</p><p>WEST COAST</p><p>ALTERNATIVE</p><p>BACC30M() HI-SHEAR</p><p>AIC</p><p>FAIRCHILD</p><p>HUCK</p><p>SPS</p><p>ALLOY STEEL,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>LUBRICATED,</p><p>160 KSI</p><p>TENSION,</p><p>CADMIUM</p><p>PLATED,</p><p>BACB30MB()-()</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>PART NUMBER</p><p>FASTENER SUBSTITUTION</p><p>MATING PARTEQUIVALENT</p><p>PART</p><p>MATING</p><p>DESCRIPTION</p><p>TBACN10YT()CD</p><p>Q</p><p>N97137 S0006585361_V1</p><p>Fastener Substitution - Bolts</p><p>Figure 2 (Sheet 25 of 67)</p><p>737-800</p><p>STRUCTURAL REPAIR MANUAL</p><p>51-40-03</p><p>GENERAL</p><p>Page 46</p><p>Mar 10/2016D634A210</p><p>ECCN 9E991 BOEING PROPRIETARY - See title page for details</p><p>ZQ</p><p>MATING</p><p>PART</p><p>EQUIVALENT MATING PART</p><p>FASTENER SUBSTITUTION</p><p>PART NUMBER DESCRIPTION</p><p>INITIAL FASTENER OR SPECIFIED</p><p>REPAIR FASTENER</p><p>BACB30NX()K()HI-SHEARA286 CRES,</p><p>AA</p><p>LUBRICATED,</p><p>AIC</p><p>FAIRCHILD</p><p>HUCK</p><p>SPS</p><p>95 KSI SHEAR,</p><p>CETYL ALCOHOL</p><p>TENSION,</p><p>160 KSI</p><p>ALUMINUM</p><p>PIGMENTED</p><p>COATING,</p><p>WEST COAST</p><p>WEST COAST</p><p>BACB30MB()AK() HL448AZ</p><p>HL448AZ</p><p>HL448AZ</p><p>HL448AZ</p><p>HL448AZ</p><p>HL448AZ</p><p>WC133</p><p>ALTERNATIVE</p><p>BACB30MB()K()</p><p>LUBRICATED,</p><p>CETYL ALCOHOL</p><p>95 KSI SHEAR,</p><p>AL COATED,</p><p>ALLOY STEEL,</p><p>OR</p><p>BACB30NX()K()</p><p>BACB30NX()K()</p><p>MAX TEMP</p><p>MAX TEMP</p><p>AA</p><p>OR</p><p>TABLE IV</p><p>BOLT - HEX DRIVE - PROTRUDING HEAD (TENSION)</p><p>OR</p><p>BACB30NX()K()</p><p>OR</p><p>350 ˚F (177˚C)</p><p>350 ˚F (177˚C)</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>BACC30BH()</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30X()</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>BACC30X()</p><p>BACC30BH()</p><p>BACC30BH()S</p><p>BACC30X()S</p><p>BACN10YT()CD</p><p>BACB30MB()-()</p><p>SPS</p><p>AIC</p><p>HUCK</p>