Pré-visualização | Página 11 de 50
too much data Data Overflow on SAP SAP of node which is sending too much data RX Duplicate Frames Duplicate frame received. Master is retrying frame, indicates communication problems Transaction Buffer Overruns Software on AN-X isn’t servicing hardware fast enough. Transaction buffer overrun Page 66 AN-X-PBSLV June 2004 Updating the Firmware The AN-X operating software consists of several parts: • boot code, runs at startup • configuration kernel, runs when you update firmware • production kernel, runs in normal operation • application software, for PROFIBUS communication, scheduled communication with ControlLogix and unscheduled messaging, and AN-X to AN-X communication The boot code and kernels are supplied in file with extension qtf and are updated using the AnxInit utility. Run the command Utilities/Update AN-X Flash and select the file you wish to download. Refer to page 49 for details. Firmware files contain the application programs for AN-X and have extension bin. They are downloaded using the command Configuration/Firmware Update or Utilities/Update Firmware in AnxInit. Refer to page 50 for details. Occasionally individual patch files are released. They have extension pch and are downloaded using the Utilities/Patch Firmware command in AnxInit. Refer to page 54 for details. Reading Version Numbers To read the version numbers of the various software components: Boot code AnxInit – AN-X Info Configuration kernel AnxInit – AN-X Info Production kernel AnxInit – AN-X Info Firmware AnxInit – AN-X Info (version depends on current mode, boot, configuration or production) Individual applications AN-X to AN-X communication Web interface, AN-X-PBSLV Bridging log ControlLogix scheduled communication and unscheduled messaging Web interface, ControlLogix Log AN-X-PBSLV Page 67 June 2004 Obtaining the Latest Software Version numbers and software for the most recent AN-X releases are available from the QTS website, www.qtsi.biz Page 68 AN-X-PBSLV June 2004 Specifications Parameter Specification Function Bridge between Ethernet and PROFIBUS network Description Processor: 100MHz IDT MIPS FLASH memory: 64M RAM: 64M Typical Power Consumption 300 mA @ 12 VDC or 150 mA @ 24 VDC Maximum Power dissipation 3.6W Environmental Conditions: Operational Temperature 0-50°C (32-122°F) Storage Temperature –40 to 85°C (–40 to 185°F) Relative Humidity 5-95% without condensation AN-X-PBSLV Page 69 June 2004 Support Technical support is available from Quest Technical Solutions. Quest Technical Solutions 4110 Mourning Dove Court Melbourne FL 32934 321 757-8483 website: qtsi.biz email: support@qtsi.biz If you need to make a return, contact QTS to obtain a return authorization number. AN-X-PBSLV Module Overview Hardware Features Installation Basic Configuration Step 1 Step 2 Step 3: Example: Standalone Computer GSD File Configuring Slaves on the AN-X-PBSLV Baud Rate PROFIBUS Nodes Configuring AN-X-PBSLV in a PROFIBUS Master Scheduled Data with a ControlLogix Mapping PROFIBUS Data Connections Configuration Requirements Reference Configuring AN-X in RSLogix 5000 Connection Parameters Configuring Input-Only Connections Connection Parameters Selecting the RPI Mapping the PROFIBUS Data Module Name I/O Data Input Data Output Data Status Input Data Sample File Sending the Configuration to AN-X Viewing the Current Configuration Error Log Exporting Tags from AN-X Using RSLogix 5000 to Diagnose Problems General Tab Connection Tab Module Info Tab AN-X to AN-X Communication Configuration File Format Configuration ID Module Definition Produce Section Produce Blocks Consume Section Consume Blocks Comments Sample Configuration File Sending the Configuration to AN-X Error Log Unscheduled Messages PCCC/PLC-5 Files Node-by-node Mapping Packed Mapping Using RSLinx Other OPC Servers Modbus over Ethernet Using AnxInit AnxInit Log Locating Available AN-X Modules Selecting an AN-X Set AN-X IP Configuration Restart an AN-X AN-X Info Read Kernel Parameters Run Config Mode Update AN-X Flash Update Firmware Firmware Update Wizard Step 1: Step 2 Step 3: Update Firmware Command Patch Firmware Using the Web Interface PROFIBUS Configuration Configure Ethernet/IP Support Define AN-X to AN-X Communication View Configuration Files View Active Configuration Monitor PROFIBUS Data Log Files System Error Log System Info Log AN-X-PBSLV Bridging Log Ethernet/IP Log View All Logs Administration Menu Troubleshooting LEDs Ethernet LEDs SYS LED NET LED – PROFIBUS Network Status Diagnostic Counters Updating the Firmware Reading Version Numbers Obtaining the Latest Software Specifications Support LogixPro/CRACK.CD-LogixPro_v1.61.zip Dt.nfo keygen.exe LogixPro/Dt (2).nfo LogixPro/Dt.nfo LogixPro/Gerando o serial do TLP-LogixPro.rtf Gerando a Chave do LogixPro Esta operação só deverá ser realizada após à instalação do LogixPro 1 - Clique em "Menu Iniciar" -> "Executar" 2 - Na janela que vai abrir, digite "cmd" (sem as aspas) 3 - Digite "cd C:\arquivos de programas\thelearningpit\logixpro" (sem aspas) ** Caso o endereço não apareça no PROMPT de comando, digite "c:" (sem aspas) Na realidade deve-se procurar onde esta a pasta "thelearningpit" pois e nela que esta instalado o logixpro 4 - Digite "logixpro.exe register" (sem aspas) 5 - Deixe a tela que vai se abrir aberta, volte ao PROMPT e digite keygen.exe 6 - Escolha um nome bem estranho (ex: "sdafghwekpojqwe") e entre com ele no Keygen e no LogixPro caso nao funcione na 1a tentativa, repita o procedimento. particularmente eu deixo o nome que esta no gerador de senha mesmo. 7 - Entre no Keygen com o número do Hardware (HWID) que aparece na tela de registro do LogixPro. ** Se aparecerem dois números, escolha o que tem "(enh)" do lado. Caso contrário (aparecendo somente um número) escolha a segunda metade do número. 8 - Com o seu Nome e HWID já escritos no Keygen, clique em Generate. 9 - Entre com a chave que aparecerá no respectivo campo do LogixPro e sua chave será criada (LogixPro liberado). *** caso apareça a mensagem de nome ou senha inválida, basta trocar o nome por outro e repetir os passos 6 a 9. LogixPro/Gerando o serial do TLP-LogixPro.txt Gerando a Chave do LogixPro Esta operação só deverá ser realizada após à instalação do LogixPro 1 - Clique em "Menu Iniciar" -> "Executar" 2 - Na janela que vai abrir, digite "cmd" (sem as aspas) 3 - Digite "cd C:\arquivos de programas\thelearningpit\logixpro" (sem aspas) ** Caso o endereço não apareça no PROMPT de comando, digite "c:" (sem aspas) 4 - Digite "logixpro.exe register" (sem aspas) 5 - Deixe a tela que vai se abrir aberta, volte ao PROMPT e digite keygen.exe 6 - Escolha um nome bem estranho (ex: "sdafghwekpojqwe") e entre com ele no Keygen
