Logo Studenta

SetupFreeSimulator

Esta es una vista previa del archivo. Inicie sesión para ver el archivo original

Fagor PC simul_Manual usuario.pdf
S IMULADOR
Manual del usuario
Ref 1307 
�
El simulador de CNC ofrece al usuario una herramienta completa para elaborar, opti-
mizar y verificar los programas directamente sobre el PC. Tras ello podrá introducirlos 
directamente en la máquina y ejecutarlos, lo que redunda en una mayor rapidez de 
trabajo.
El simulador tiene la misma operativa que un CNC instalado en máquina. Dispone 
de las mismas potencialidades que el CNC y puede personalizarse con la misma 
configuración que una máquina real. Reproduce fielmente el comportamiento de la 
máquina respetando las aceleraciones, velocidades... que se dan en la realidad.
Su uso más habitual será:
• Formación técnica para programadores y operarios en centros de formación.
• Edición/Simulación en departamentos de diseño.
• Estimación del tiempo de mecanizado.
• Preparación de presupuestos.
INTRODUCCIÓN
Capítulo 1 Introducción
3
INSTALACIÓN
Ejecute el fichero “SetupFreeSimulator.exe”.
Aparecerá la ventana siguiente. Pulse “Install” para continuar.
instalando
Si durante el proceso de instalación aparece una ventana emergente con el mensa-
je “Invalid file handle 32”, pulse “Aceptar” y continúe. Es un error que se activa por 
estar el Outlook activado mientras se está instalando, pero no afecta a la instalación 
final.
Capítulo 2 Instalación
�
PUESTA EN MARCHA
Ejecutando el simulador
El instalador habrá creado el siguiente icono en su escritorio. 
Si lo ejecuta, aparecerá la pantalla siguiente:
Selección de máquina (Fresadora-Torno)
La primera página del software presenta las siguiente opciones.
Librería de máquinas para que el simulador arranque con una configuración determinada.
Capítulo 3 Puesta en marcha
�
Opciones para trabajar con esa librería:
 F1 F� F3 F� F� F6 F7
F1 - Crear una nueva máquina usando la actual como plantilla
F2 - Propiedades de la máquina seleccionada
F3 - importar una máquina
F4 - Exportar la máquina seleccionada
F5 - Borrar la máquina seleccionada
F6 - Ejecutar el simulador con la máquina seleccionada
F7 - Salir del programa
Capítulo 3 Puesta en marcha
6
DESCRIPCIÓN DEL 
TECLADO Y LA PANTALLA
Descripción del interface
Seleccionar el modelo de máquina y pulsamos
Al finalizar el arranque del programa, aparecerá la siguiente información
* El idioma que aparece por defecto es en Inglés. Para cambiar el idioma, véase la página 8
Pantalla principal y teclas 
de navegación
Teclado alfanumérico
Zona de control de 
ejes y cabezal (JOG)
Capítulo 4 Descripción del teclado y la pantalla
7
Para cerrar la aplicación pulse la 
tecla
Aparecerá el siguiente menú donde seleccionaremos “Close”
Capítulo 4 Descripción del teclado y la pantalla
�
*Cambiar idioma
Seleccione 
para ver
más opciones
Seleccione la op-
ción de “Machine 
parameters”
Capítulo 4 Descripción del teclado y la pantalla
* Cambiar el idioma
�
Seleccione“HMI”
Capítulo 4 Descripción del teclado y la pantalla
* Cambiar el idioma
10
Seleccione el idioma 
que quiera utilizar
Capítulo 4 Descripción del teclado y la pantalla
* Cambiar el idioma 
11
Para validar el idioma, necesita 
resetear la aplicaión. 
Seleccione “CNC OFF” y luego 
pulse “Restart”.
Capítulo 4 Descripción del teclado y la pantalla
* Cambiar el idioma
1�
Descripción del teclado (Teclado alfanumérico)
Capítulo 4 Descripción del teclado y la pantalla
13
Teclas para desplazar el cursor
- Las flechas desplazan el cursor una posición a la iz-
quierda, a la derecha, hacia arriba o hacia abajo.
- Las teclas retroceder o avanzar página muestran la 
página anterior o posterior, en el editor de programas 
pieza o de PLC.
Teclas clásicas del PC
- Esta serie de teclas funcionan de la misma manera en que funcio-
nan en su PC. 
- Se incluyen para ofrecer una operativa similar al CNC real y para 
agilizar el trabajo del usuario.
Teclas genéricas 
Esta tecla da acceso al menú principal del CNC, la página de inicio
Tecla configurable por parámetro para acceder a un modo de trabajo 
del CNC o ejecutar una aplicación externa.
Tecla para cerrar el simulador, apagar el CNC.
Capítulo 4 Descripción del teclado y la pantalla
1�
Teclas de acceso a los modos de trabajo
Automático – Para seleccionar y ejecutar programas
Manual – Para realizar operaciones manuales en máquina
Edición – Para editar y simular programas (verificarlos) antes de ejecutarlo
MDI – Para ejecutar bloques unitarios programados por el usuario
Tablas – Da acceso a tablas de referencias pieza, parámetros de programa-
ción,…
Herramientas – Accede a la tabla de herramientas
Utilidades – Modo de trabajo para la gestión de ficheros (similar al explorador 
de Windows).
Teclas para edición
Calculadora – Superpone una calculadora cuyos resultados se pueden 
introducir en distintos campos del CNC.
Valida comandos, datos y los bloques de programa del editor.
Cambiar el estado de los icono cuando el foco está sobre él.
Recupera datos para la edición y ciclos ya programados para modificarlos.
Insertar o sobreescribir. Permite insertar un ciclo editado en un programa.
Capítulo 4 Descripción del teclado y la pantalla
Las siguientes teclas permiten al usuario acceder directamente a los principales mo-
dos de trabajo del CNC.
Las siguientes teclas facilitan al usuario la programación y la navegación en los modos de 
edición.
1�
Descripción del teclado (Zona de control de ejes y cabezal (JOG))
Teclas de navegación y ayuda
Accede al capítulo del manual que explica la operación que el usuario 
esté realizando
Permite acceder secuencialmente a las distintas pantallas disponibles del 
modo de trabajo activo
Permite mover el foco entre las distintas ventanas de la pantalla
Teclas para el control de ejes 
Las teclas siguientes permiten desplazar los ejes en el modo de trabajo manual o 
durante la inspección de herramienta en el mecanizado. 
El signo + o – indican el sentido de desplazamiento del eje en cuestión y la tecla 
superior derecha define si el movimiento se va a hacer a máxima velocidad (G00) 
o a la velocidad que esté programada en ese momento (G01).
Capítulo 4 Descripción del teclado y la pantalla
16
Realiza la búsqueda de referencia máquina de todos los ejes de manera 
simultánea.
Ejecuta línea a línea (bloque a bloque) el programa seleccionado, dete-
niéndose al final de cada línea.
Inicializa el sistema poniendo las condiciones iniciales, definidas en los 
parámetros máquina.
Teclas para el control del cabezal
Teclas de propósito general
Capítulo 4 Descripción del teclado y la pantalla
Estas teclas verticales permiten:
Aumentar en % la velocidad del cabezal
Orientar la posición del cabezal
Reducir en % la velocidad del cabezal
Arrancar el cabezal a derechas
Parar el cabezal
Arrancar el cabezal a izquierdas
17
Teclas configurables
Tecla de marcha (START).
Ejecutar el programa seleccionado en el modo automático, un bloque en 
modo MDI/MDA, etc.
Teclas de marcha/parada
Tecla de parada (STOP).
Interrumpir la ejecución del CNC que ha sido lanzada con el START
Las funciones de estas teclas son definidas por el fabricante de la máquina, y permiten controlar los dife-
rentes dispositivos de la máquina. 
En el software de simulación, estas teclas no tienen ninguna función asociada.
Selectores de movimientos
y avances
*Mediante el uso de las flechas (◄►) el usuario puede seleccionar:
- El tipo de movimiento manual ; Continuo, incremental o volantes.
- El porcentaje de avance, entre el 0% y el 200%, para los movimientos en manual y automático.
Capítulo 4 Descripción del teclado y la pantalla
1�
Descripción de la pantalla principal y teclas de navegación
El simulador ofrece una serie de accesos directos en zonas de la pantalla para facilitar la 
navegación del usuario.
Pantalla principal
Teclas
de 
navegación
Capítulo 4 Descripción del teclado y la pantalla
Zona de accesos directos
1�
Accesos directos del simulador. 
Para salir pulse “ESC”
Teclas
de 
navegación
Pantalla principal (Zona de accesos directos)
El simulador ofrece una serie de accesos directos en zonas de la pantalla para facilitar la 
navegación del usuario. Basta con pulsar con el ratón sobre la zona indicada.
Capítulo 4 Descripción del teclado y la pantalla
Si esta ventana está en estado 
de error (color rojo), pulse la 
tecla RESET para borrarlo y 
seguir trabajando.
�0
Nombre del programa
 en ejecución
Ciclo en ejecución 
en el programa
Avisos activados
por el CNC
Avisos activados 
por el autómata
Pantalla principal (Avisos y Errores)
El CNC previene de errores que se hayan podido cometer y da avisos al usuario. Los erro-
res vendrán indicados en color “rojo” y los avisos estarán en color “verde”.
Los errores se pueden anular pul-
sando la tecla “Reset” y en algunos 
casos, si aparece el icono “ESC” con 
esa misma tecla. El icono de “?” indi-
ca que existe una ayuda para resolver 
el problema pulsando la tecla “Help”.
Capítulo 4 Descripción del teclado y la pantalla
�1
Pantalla principal (Modo conversacional)
Para aquellos operarios que lo deseen, Fagor Automation facilita sus ciclos de programa-
ción conversacionales. El operario no tiene la necesidad de dominar el lenguaje de pro-
gramación ISO, basta con definir la geometría de la pieza a realizar, la herramienta y las 
condiciones de mecanizado, y el CNC se encarga de realizar el resto. 
Fagor ofrece un modo de trabajo particular para este lenguaje de programación que se ac-
cede pulsando simultaneamente las teclas SHIFT y ESC de su teclado.
“SHIFT”+“ESC”
Nota: Para aquellos usuarios familiarizados con el CNC 8055 de Fagor, la activación de este modo de trabajo 
se hace pulsando secuencialmente SHIFT y luego ESC. En este simulador hay que pulsar a la vez estas 
teclas.
Capítulo 4 Descripción del teclado y la pantalla
��
Pantalla principal (Manuales integrados)
El CNC lleva integrados los manuales de operación y programación. Pulsando la tecla HELP, 
el CNC mostrará en pantalla el capítulo relativo a la operación que se está realizando en ese 
momento. Una vez dentro de los manuales se podrá consultar cualquier otra información,
navegando entre sus distintos capítulos.
Para salir de la zona de manuales, pulse “ESC”.
Capítulo 4 Descripción del teclado y la pantalla
Fagor PC simul_User manual.pdf
S IMULATOR
User manual
Ref 1307 
�
The CNC simulator provides the user with a complete tool to create, optimize and 
check programs directly at the PC. He can then transfer them directly on the machine 
and run them which means working faster.
The simulator operates the same way as a CNC installed on a machine. It offers the 
same features as the CNC and may be set with the same configuration as a real ma-
chine. It faithfully reproduces the behavior of the machine respecting the acceleratio-
ns, speeds, etc. that are used in real life.
Its most common use will be:
• Technical training for programmers and operators in training centers..
• Editing/Simulation in design departments..
• Machining time estimate.
• Quotation preparation.
INTRODUCTION
Chapter 1 Introduction
3
INSTALLATION
Run the fi le “SetupFreeSimulator.exe”.
It will show the following window. Press “Install” to continue.
instalando
If during installation, a pop-up window appears with the message “Invalid fi le handle 
32”, press “OK” and continue. It is an error that comes up because Outlook is active 
during installation, but it does not affect the fi nal installation.
Chapter2 Installation
�
START -UP
Running the simulator:
The installer will have created the following icon on your desktop.:
Machine selection (Mill-Lathe)
The first screen of the software shows the following options.
Machine library so the simulator starts up with a specific configuration.
Chapter 3 Start - up
�
Options for working with that library:
 F1 F� F3 F� F� F6 F7
F1 - Create a new machine using the current one as a template
F2 - Properties of the selected machine
F3 - Import a machine
F4 - Export the selected machine
F4 - Delete the selected machine
F6 - Run the simulator with the selected machine
F7 - Exit the program
Chapter 3 Start - up
6
KEYBOARD & SCREEN
DESCRIPTION
Interface description
Select the machine model and press
When the program start-up is done, it will show the following information
* If you want to change the language go to page8
Main screen and
browsing keys
Alphanumeric
keyboard
Area for controlling 
axes and spindle 
(JOG)
Chapter 4 Keyboard & Screen description
7
To close the application, press:
It will show the following menu, select “Close”
Chapter 4 Keyboard & Screen description
�
*Change the language
Open to show
more options
Select the “Machi-
ne parameters”
option
Chapter 4 Keyboard & Screen description
* Change the language
�
Select“HMI” parameter group
Chapter 4 Keyboard & Screen description
* Change the language
10
Select the language
you would like to use
Chapter 4 Keyboard & Screen description
* Change the language
11
To validate the new language you need to 
restart the application.
Select “CNC OFF” and after “Restart”
Chapter 4 Keyboard & Screen description
* Change the language
1�
Alphanumeric keyboard description
Chapter 4 Keyboard & Screen description
13
Keys to move the cursor
- The arrow keys move the cursor one position to the left, 
right, up or down.
- The previous-page or next-page keys show the previous or 
next page at the part-program or PLC program editor.
Classic PC keys
These keys work the same way as at your PC. They are included to
provide the same operation as at a real CNC and to make the user’s 
job easier.
Generic keys
This key gives access to the main menu of the CNC, the home page
Key that may be configured by parameter to access the CNC
work mode or execute an external application.
Key to close the simulator, turn the CNC off
Chapter 4 Keyboard & Screen description
1�
Hotkeys to work modes.
Automatic – To select and run programs
Manual – (JOG) to run manual operations at the machine
Edit – To edit and simulate programs (verified) before executing them
MDI – To execute single blocks programmed by the user
Tables – To access part-reference tables, programming parameters, etc.
Tools – To access the tool table
Utilities – Work mode for managing files (similar to Windows
Explorer).
Editing keys
Calculator – It overlays a calculator whose results may be entered into 
various
It validates commands, data and program blocks of the editor.
It toggles the status of the icon
when the focus is on it.
It restores data for editing and already programmed cycles for editing them.
Insert or overwrite. It allows inserting a previously edited cycle into a program.
Chapter 4 Keyboard & Screen description
The following keys provide access to the main work modes of the CNC.
The following keys help the user program and navigate (browse) in the editing modes.
1�
Keyboard description (Area for controlling axes and spindle (JOG))
Browsing and help keys
It gives access to the chapter of the manual that describes the operation 
the
It is used to sequentially access the different available screens of the ac-
tive work mode.
It is used to move the focus between the different windows of the screen.
Axis control keys
The following keys may be used to move the axes in jog mode or during tool while ma-
chining.
The + and – signs indicate the moving direction of the particular axis and the “wavy” key 
defines the rapid movement at maximum speed (G00) or the speed programmed at the 
time (G01)
Chapter 4 Keyboard & Screen description
16
It does a home search on all the axes at the same time.
Executes the selected program one block at a time (single block mode) 
stopping at the end of each line.
It initializes the system setting the initial conditions as defined by machine
parameters.
Spindle control keys
General purpose keys
Chapter 4 Keyboard & Screen description
These vertical keys may be used to:
Increase the spindle speed by a %
Orient the spindle
Decrease the spindle speed by a %
Start the spindle clockwise
Stop the spindle
Start the spindle counterclockwise.
17
Configurable keys
Cycle start key (START).
Execute the selected program in automatic mode, a block in MDI/MDA
mode, etc.
Start/Stop keys
Cycle stop key (STOP).
Interrupt the execution of the CNC that was launched with the START key
The functions of these keys are defined by the machine manufacturer and they allow controlling the various
devices of the machine.
In the simulation software, these keys have no associated function.
Movement and feedrate selectors
*Using the arrow keys (◄►) the user can select:
- The type of jog movement; Continuous, incremental or handwheels.
- The percentage of feedrate override, between 0% and 200%, for jog and automatic movements.
Chapter 4 Keyboard & Screen description
1�
Description of the main screen and browsing keys
The simulator offers several hotkeys in screen areas for easier browsing (navigation).
Main screen
Browsing
keys
Chapter 4 Keyboard & Screen description
Area for hotkeys
1�
Simulator hotkeys.
Press “ESC” to exit
Browsing
keys
Main screen (Area for hotkeys)
The simulator offers several hotkeys in screen areas for easier browsing (navigation). Just
click with the mouse on the indicated area.
Chapter 4 Keyboard & Screen description
If the window is in an error
state (red), press the RESET 
key to delete it and go on wor-
king
�0
Name of the program in
execution
Cycle in execution in the
program
Warnings activated
by the CNC
Warnings activated
by the PLC
Main screen (Warnings and Errors)
The CNC warns about possible errors and warns the user. Errors are displayed in red and
warnings in green.
Errors may be canceled by
pressing the “Reset” key and,
sometimes, if the “ESC” is
displayed by pressing that key.
The “?” icon indicates that there
is help for solving the problem by
pressing the “Help” key.
Chapter 4 Keyboard & Screen description
�1
Main screen (Conversational mode)
If the operator prefers it, Fagor Automation offers its conversational programming cycles.
You don’t need to master the ISO programming language, you just define the geometry of
the part to be made, the tool and the machining conditions and the CNC will do the rest.
Fagor offers a particular work mode for this programming language that may be accessed
by pressing the SHIFT and ESC keys at the same time.
“SHIFT”+“ESC”
Note: For users already familiar with Fagor CNC 8055, this mode is activated by pressing SHIFT and then ESC. At this 
simulator these keys must be pressed at the same time.
Chapter 4 Keyboard & Screen description
��
Main screen (Integrated manuals)
The CNC integrates the operating and programming manuals. Pressing the HELP key, the
CNC displays the chapter related to the operation being carried out at the time. Once inside 
the manuals, it is possible to consult any other information by browsing through its various
chapters.
Press “ESC” to exit from the manuals area.
Chapter 4 Keyboard & Screen description
Fagor PC simul_Opciones.pdf
EJES
EJES INTERPOLADOS
CABEZALES
ALMACENES
CANALES
Compensación radio herramienta
Mecanizado alta velocidad HSSA
Edición / Simulación
Editor de perfiles
Ciclos fijos de palpador
Eje C 
Eje Y en Torno 
Sincronismos y levas
Control tangencial
Máquina combinada 
RTCP
Gráficos F3D
Conversacional IIP
Ciclos de usuario en FC
Compensación Volumétrica Media
Compensación Volumétrica Grande
Edición PROGTL3
Traductor de programas CNC
VERSIÓN
GRATUITA
VERSIÓN
COMPLETA
3
3
1
1
1
28
28
6
4
4
Para más información: Tel.: +(34) 943 039 800 | info@fagorautomation.es | www.fagorautomation.com
SIMULADOR CNC 806x - 807x
Fagor PC simul_Options.pdf
AXES
INTERPOLATED AXES
SPINDLES
MAGAZINES
CHANNELS
Tool radius compensation
HSSA High speed machining
Editing / Simulation
Profile editor
Probing canned cycles
"C" axis 
Y axis on lathe 
Synchronism and cams
Tangential control
Dual-purpose machine 
RTCP
F3D graphics
Conversational IIP
User cycles in FC
Medium volumetric compensation
Large volumetric compensation
PROGTL3 editing
CNC program translator
FREE
VERSION
FULL
VERSION
3
3
1
1
1
28
28
6
4
4
For further information: Tel.: +(34) 943 039 800 | info@fagorautomation.es | www.fagorautomation.com
806x - 807x CNC SIMULATOR
SetupFreeSimulator.exe