Prévia do material em texto
Virus Plaque Assay Protocol DEFINITIONS: • Plaque: an area of cells in a monolayer which display a cytopathic effect, e.g. appearing round and darker than other cells under the microscope, or as white spots when visualized by eye; the plaque center may lack cells due to virus-induced lysis. • Plaque-forming unit (PFU): a virus or group of viruses which cause a plaque. MATERIALS AND EQUIPMENT • Cell Growth Media (DMEM high glucose with L-glutamine and 10% fetal bovine serum); Pen- Strep and Fungizone can be added if desired • Plaquing Medium (DMEM high glucose with L-glutamine and 1% fetal bovine serum) • CMC (Carboxymethylcellulose) • Tissue culture grade water • Eppendorf or similar pipettors capable of dispensing 10 to 100 μl • Tubes to make your dilutions • 24 well tissue culture plates - Certain cell lines such as 293 are very sensitive to manipulation and pH and may require dishes pre-coated with Collagen. Such dishes are commercially available from Biocoat, Falcon HARVEST AND PLATING OF CELLS IN 24-WELL PLATES 1. Make a solution of cells at 4 x 105 cells per ml in Growth Media (24 hours confluenc. 2. Add 0.5 ml of growth media with cells to each well. Jiggle the plate to evenly distribute cells. Incubate plates in a 37°C, CO2 incubator. 3. After ~12-24 hours, the cells should be ~90-100% confluent. Go on to the next step immediately. Waiting several more days for cells to become completely confluent is not optimal. VIRUS DILUTION 1. 2. 3. Prepare dilutions of virus in PBS or DMEM. Never make more than a 100-fold dilution; always pipette at least 10 µl of virus or solution to reduce pipetting error. First dilution: 50ul of virus to 450ul media. Repeat the dilution process through all four tubes. The tubes will now have these effective dilutions of virus: 10-2(1/100), 10-4 (1/10,000), 10-6 (1/1,000,000), 10-8 (1/100,000,000). PAGE 2 INFECTION OF THE MONOLAYERS 1. Add 200 µL of each dilution in duplicate to each well, letting the virus flow gently into the media. 2. Incubate the infected monolayers at 37°C for one hour; mildly shake the plates gently several times during this adsorption period (every 15 minutes). CMC (CarboxyMethylCellulose) OVERLAY 1. Prepare a sterile solution of 3% CMC in dH2O by autoclaving at 121°C for 20 minutes. CMC may be stored at 4ºC. 2. Warm the plaquing media in a 37°C water bath until equilibrated. Make absolutely sure your media is at 37°C. 3. Gently draw media out of each infected monolayer well and discard. 4. Mix the equal volume of 2x media 2% FBS and CMC. Shake vigorously to mix. 5. With a new pipette, immediately but gently add 0.5 ml of the CMC/growth media mixture to each well. 6. Move the plate(s) to a humidified incubator at 37°C and 7.5 to 5% CO2. Some viruses require different temperatures. PLAQUE VISUALIZATION • Plaques will be visible by day 2 to 11 after infection, depending on the virus. Remove CMC media and fix the cells with 10% formaldehyde (in PBS 1x). Stain the monolayer with crystal violet (1g/20ml ethanol/80ml dH2O - Filter). First add water, dilute Crystal Violet, and then add Ethanol. Crystal Violet PFU/ml CALCULATION • After counting plaques, you can calculate the concentration of the initial viral suspension in PFU/ml. • Take the dilution of virus you plated and the volume of virus solution you placed on the single monolayer to determine the PFU/ml. • Example: If you placed 200 µl of virus dilution, the last well with plaques will be the dilution factor for plaques, but you have multiply the plaque number by 5 (1000mL). Example: if the last dilution with plaques was 10-6, and you have 4 plaques, your virus titer will be 20x106 or 2x107 PFU/ml.