What are the steps to build a metal partition?
Clean the dust from the wall, floor, and ceiling where the partition will be built.
Mark the locatio...

Question

What are the steps to build a metal partition?
Clean the dust from the wall, floor, and ceiling where the partition will be built.
Mark the location of the partition on the floor using a chalk line.
Transfer this layout to the walls and ceiling using a ruler and plumb line.
Cut the metal profiles (channels and uprights) to the necessary size.
Fix the channel to the floor using suitable plugs and screws.
Place the channel on the ceiling, level with the channel on the floor, and fix it with the same plugs and screws.
Place the first vertical profile (upright).
Place the door frame by screwing it to the upright with self-tapping screws.
Cut a piece of upright the width of the door frame plus two lateral brackets of 15 to 20 cm.
Place the second upright on the other side of the door, screwing it to the floor channel, ceiling channel, and door frame.
Introduce the uprights between the floor and ceiling channels every 40 or 60 cm.
Pass the electrical tubes that will supply power to the outlets and switches.
Cut the plates to the necessary size.
Place two wedges of 1 cm under the plate and, with a lever, insert it fully into the ceiling channel.
Fix the plates to the uprights with special screws.

Ed · Answer

Os passos para construir uma divisória de metal são:

1. Limpar a poeira da parede, piso e teto onde a divisória será construída.
2. Marcar a localização da divisória no piso usando uma linha de giz.
3. Transferir esse layout para as paredes e teto usando uma régua e linha de prumo.
4. Cortar os perfis de metal (canais e montantes) no tamanho necessário.
5. Fixar o canal no piso usando buchas e parafusos adequados.
6. Colocar o canal no teto, nivelado com o canal no piso, e fixá-lo com as mesmas buchas e parafusos.
7. Colocar o primeiro perfil vertical (montante).
8. Colocar o batente da porta parafusando-o no montante com parafusos autoperfurantes.
9. Cortar um pedaço de montante com a largura do batente da porta mais dois suportes laterais de 15 a 20 cm.
10. Colocar o segundo montante do outro lado da porta, parafusando-o no canal do piso, canal do teto e batente da porta.
11. Introduzir os montantes entre os canais do piso e do teto a cada 40 ou 60 cm.
12. Passar os tubos elétricos que fornecerão energia para as tomadas e interruptores.
13. Cortar as placas no tamanho necessário.
14. Colocar dois calços de 1 cm sob a placa e, com uma alavanca, inseri-la completamente no canal do teto.
15. Fixar as placas nos montantes com parafusos especiais.

What are the steps to build a metal partition? Clean the dust from the wall, floor, and ceiling where the partition will be built. Mark the locatio...

Livro Curso Basico D...pdf

Colégio Objetivo

Essa pergunta também está no material:

Como aplicar placas de yeso en techos y paredes - 2

Design de Interiores • ArtesArtes

Respostas

Responda

Continue navegando

Perguntas relacionadas

How to install GYPLAC® plasterboard? Preparation of the wall or partition Adhesion of GYPLAC® plasterboard to the wall or partition Materials neede...

What is the resistance to fire of a brick partition covered with 1.5 cm of plaster on both sides, according to Table 7? A brick partition covered ...

What are the tools needed to install a curtain rod? It is essential to use screws and plugs adapted to the type of wall or ceiling. There are spec...

What are the steps to construct a Durlock® wall? Reposition the wall using a taut thread and fix the bottom plate to the floor with nylon expansion...