Baixe o app para aproveitar ainda mais
Prévia do material em texto
Hoisting & Driving Tools SAFETY DRIVE HAMMER SAFE-T-DRIVER HOIST CABLE HEAVY DUTY GIMBAL COUPLING IN-HOLE SAMPLING HAMMER “J” SERIES DRILL ROD 3-1/4? I.D. 3-Key HSA AW-AWJ PIN-TO-PIN SUB SPLIT BARREL SAMPLER CUTTERHEAD CUTTERHEAD LOCKING BOLT Safety Drive Hammer www.drillingworld.com Description Part # lb./kg Hammer Assy, Safety: 140 lb (63.5kg), AWJ Pin 67028-01 190 (86.2) Hammer Assy, Safety: 300 lb(136.1kg), NWJ Pin 67028-02 351 (159.2)) Drive hammer design results in a safe, accurate, one piece hammer that requires no jar length, jar or bump block. The center rod and impact block are cast or forged as one piece to provide maximum durability during the driving process. Hammer action is totally enclosed for safety. Maximum impact block travel allows for a 2′6″ (762mm) free-fall. The machined, heavy-duty rod connection is AWJ (1-3⁄4″(44mm) O.D.) for the 140 lb (63.5kg) hammer or NWJ (2-5⁄8″ (67mm) O.D.) for the 300 lb (136.1kg) hammer. Figure 5-2 4 2 1 3 AWJ for 140 NWJ for 300 Safety Drive Hammer Assembly 140 lb For SPT Work Ref. Description Part No. Lb/Kg 1 Weldment, Sleeve 190086 127 (57.6) 2 Center Rod 190066 28 (12.7) 3 Cap,Guide 190084 14 (6.4) 4 Capscrew, Hex Socket Head (8 Required) 3137-0079 * AWJ Box To A Pin 180011-01 2 (.9) AWJ Box To AW Pin 180011-02 3 (1.4) AWJ Box To BW Pin 180011-03 4 (1.8) AWJ Box To N Pin 180011-04 6 (2.7) AWJ Box To NW Pin 180011-05 6 (2.7) AWJ Box To NWJ Pin 180011-06 6 (2.7) 300 lb. For Driving Casing 1 Weldment, Sleeve 190090 295 (133.8) 2 Center Rod 006990 39 (17.7) 3 Cap, Guide 190091 17 (7.7) 4 Capscrew, Hex Socket Head (8 Required) 3134-0090 * NWJ Box To A Pin 180012-01 5 (2.3) NWJ Box To AW Pin 180012-02 5 (2.3) NWJ Box To AWJ Pin 180012-06 6 (2.7) NWJBox To BW Pin 180012-03 5 (2.3) NWJ Box To N Pin 180012-04 5 (2.3) NWJ Box To NW Pin 180012-05 5 (2.3) Component Parts Drive hammer design results in a safe, accurate, one piece hammer that requires no jar length, jar or bump block. The center rod and impact block are cast or forged as one piece to provide maximum durability during the driving process. Hammer action is totally enclosed for safety. Maximum impact block travel allows for a 2′6″ (762mm) free-fall. The machined, heavy-duty rod connection is AWJ (1-3⁄4″(44mm) O.D.) for the 140 lb (63.5kg) hammer or NWJ (2-5⁄8″ (67mm) O.D.) for the 300 lb (136.1kg) hammer. 5-3A 1 3 2 AW Rod Box 2-7/8 (73mm) In-Hole Sampling Hammer DrillingWorld 1-800-331-9988 Description Part # lb./kg Hammer Assy: 10′1″ (3.07m) Closed, 140 lb (63.5kg), AW box 006297-01 180 (81.6) Ref. Description Part No. Lb/Kg 1 Swivel, Ball Bearing with Bolt and Nut 006305 5 (2.3) 2 Bolt and Nut 006748 * 3 Hammer without Swivel 006297-10 168 (76.2) Component Parts In-Hole Sampling Hammer 2-7/8” (73mm) O.D. In-Hole Sampling Hammer is a 140 lb. (63.5kg) free-fall drive weight incorporating an enclosed “jars” assembly with a 3′6″ (914mm) maximum stroke length. It is supplied with a AW rod box thread at the bottom end for direct attachment of a chopping bit, sampler or drill rod using an appropriate pin- to pin adapter. The top connection is a 3 ton (2.7t) capacity ball bearing swivel with a bullet nosed thimble cap which will accept wire rope to 1⁄2″ (13mm) diameter. Operation can be by SAFE-TDRIVER or free-spooling sandline and other actuating means that would normally be acceptable for use with a conventional or safety type drive hammer. Through the spindle sampling, is possible utilizing a Gimbal Coupling and the hammer connected directly to the sampler in its “in-hole” mode. Direct connection of the sampler to hammer also eliminates the loss of hammer energy to the sampler which is common in deep holes and provides considerable operational economy through the elimination of drill rod handling. The In-Hole Hammer can be used with drill rods between the sampler and hammer and is recommended in wet bore holes to keep the hammer above the water level. Description Part No. Lb/Kg 1-13/16” (46mm), A Rod Box 002096 3 (1.4) 2-3/4” (70mm), A Rod Box 002097 5 (2.3) 2-1/4” (57mm) AW Box 006870 3 (1.4) 2-3/4” (70mm), AW Rod Box 007163 7 (3.2) 3-1/4” (83mm), N Rod Box 002099 8 (3.6) Straight Chopping Bit with Rod Box Connection Hoisting Tools www.drillingworld.com Rod Lifter Description Part No. Lb/Kg Closed Eye (EW) 002640 13 (5.9) Closed Eye (AW, AWJ) 002641 13 (5.9) Closed Eye (BW) 002642 14 (6.4) Closed Eye (NW & NWJ) 002643 16 (7.3) Open Eye (AW & AWJ) 005674 12 (5.4) Open Eye (NW & NWJ) 005673 16 (7.3) Open Eye (EW) 005676 11 (5) Rod Ring Closed Description Part No. Lb/Kg A Rod 002621 7 (3.2) AW & AWML Rod 002625 7 (3.2) B Rod 002622 12 (5.4) BW Rod 002626 10 (4.5) E Rod 002620 6 (2.7) EW Rod 002624 12 (5.4) N Rod 002623 13 (5.9) NW & NWML Rod 002627 10 (4.5) Rod Open Description Part No. Lb/Kg A Rod 002629 7 (3.2) AW & AWML Rod 002633 7 (3.2) B Rod 002630 11 (5) BW Rod 002634 10 (4.5) E Rod 002628 6 (2.7) EW Rod 002632 6 (2.7) N Rod 002631 13 (5.9) NW & NWJ Rod 002635 9 (4.1) Description Part No. Lb/Kg A Pin 64135-06 12 (5.4) AW Pin 64135-05 11 (5) AWJ Pin 64135-02 11 (5) NW Pin 64135-03 16 (7.3) NWJ Pin 64135-01 16 (7.3) Ball Bearing Hoisting Plug Lowering Iron with Jaw Description Part No. Lb/Kg AW, AWJ 002748 24 (10.9) BW 002749 21 (9.5) EW 002747 17 (7.7) NW, NWJ 002750 23 (10.4) Hoisting Tools Gunnebo Hoisting Hooks DrillingWorld 1-800-331-9988 Hoisting Hooks Description Part No. Lb/Kg 3 Ton Hook Gunnebo 3840-0003 4.3 (2.0) Latch Kit 218071-03 * 4 Ton Hook Gunnebo 3840-0004 8.4 (3.8) Latch Kit 218071-04 * 7 Ton Hook Gunnebo 3840-0005 15 (6.8) Latch Kit 218071-05 * Description Part No. Lb/Kg 1 Ton Hook 3061-0002 2 (.9) 3 Ton Hook 3061-0004 3 (1.4) Latch Kit 3062-0004 * 4-1/2 Ton Hook 3061-0005 6 (2.7) Latch Kit 3062-0005 * 7 Ton Hook 3061-0006 9 (4.1)
Compartilhar