Configuração SFU NOKIA 7360

Prévia do material em texto

<p>Configuração SFU HALNy HL-</p><p>1GE/HL-1GE2 [NOKIA 7360]</p><p>Criado em15 casas 2020</p><p>Última atualização em31 de janeiro de 2024</p><p>Você está aqui:</p><p> Principal</p><p> Configuração OLT</p><p> NOKIA ISAM 7360</p><p> Configuração SFU HALNy HL-1GE/HL-1GE2 [NOKIA 7360]</p><p>< Todos os Tópicos</p><p>Configuração HALNy HL-2BV</p><p>Cenário de serviço</p><p>HL-1GE / HL-1GE2 pode trabalhar em dois modos – HGU (Home Gateway</p><p>Unit) e SFU (Single Familly Unit).</p><p>A configuração do modo HGU é apresentada aqui é semelhante para HL-</p><p>4GMV.</p><p>A alteração do modo ONT é obtida configurando/não a porta de ponte e</p><p>VEIP para ONT. Por exemplo, se ONT tiver que estar funcionando como HGU,</p><p>precisamos definir apenas VEIP. Se como SFU, precisamos definir apenas</p><p>porta(s) de ponte.</p><p>O modo SFU permite preparar configurações mais complexas – como túnel</p><p>QiQ ou tradução de VLAN no ONT. Neste tutorial, focaremos na configuração</p><p>do modo SFU.</p><p>Comutação de modos ONT HGU<-</p><p>>SFU</p><p>https://halny.com/knowledge-base/</p><p>https://halny.com/knowledge-base/kategoria/olt-configuration/</p><p>https://halny.com/knowledge-base/kategoria/olt-configuration/nokia-7360/</p><p>ONT HL-1GE / HL-1GE2 suporta comutação de modo automático com</p><p>atribuição de acordo com a configuração. No momento, essa função é</p><p>suportada em:</p><p> Dasan OLT</p><p> Zyxel OLT</p><p> Alcatel Lucent OLT</p><p>Como alternar entre SFU/HGU.</p><p>Cenário de serviço SFU suportado e configuração ONT</p><p>Data e versão do documento 2020.05.15</p><p>Testado em OLT NOKIA 7360 FX-4 Versão: L6GPAA56.587</p><p>Testado com ONT HALNy HL-1GE / HL-1GE2 SFU Suportado na versão: V2.0.10 ou superior</p><p>Revisão 1</p><p>1. Configuração ONT (Modo de acesso – somente INTERNET)</p><p>O ONT está conectado à porta 1/1/1 com o ID onu 8 1. Crie a interface</p><p>ONT e configure o estado do administrador</p><p>admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:0002F163</p><p>sw-ver-pland disabled iphc-allowed enable enable-aes disable</p><p>configure>equipment>ont>interface>1/1/1/1/8 admin-state up</p><p>2. Planeje o tipo de slot do cartão e defina a quantidade e o tipo de</p><p>portas (1 ETH no caso de HL-1GE)</p><p>admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type</p><p>10_100base plndnumdataports 1 plndnumvoiceports 0 admin-state up</p><p>NOTA:</p><p>O slot 1 é para placa Ethernet -> #configure equipment ont slot</p><p>1/1/1/1/8/ 1</p><p>3. Crie um perfil de QoS</p><p>https://halny.com/knowledge-base/sfu-hgu-how-to-change-mode/</p><p>https://halny.com/contact/</p><p>#configure qos profiles bandwidth 1G committed-info-rate 0 assured-</p><p>info-rate 0 excessive-info-rate 1000000</p><p>4. Defina a velocidade da porta Ethernet/duplex e atribua o perfil DBA</p><p>admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-</p><p>state up</p><p>admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0</p><p>bandwidth-profile name:1G</p><p>5. Adicione vlan 100 à porta da ponte</p><p>admin>#configure bridge port 1/1/1/1/8/1/1</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 100 tag untagged</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>100$ exit</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1# pvid 100</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1# max-unicast-mac 200</p><p>6. Opcionalmente configure ip-host1</p><p>#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-</p><p>profile name:1G</p><p>#configure bridge port 1/1/1/1/8/vuni</p><p>#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400</p><p>#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400</p><p>#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up</p><p>7. Exibir endereço IP do host 1 do ONT</p><p>#show iphost ont operational-data</p><p>operational-data table</p><p>=======================================================================</p><p>==================================</p><p>index |ip-address |net-mask |default-</p><p>router |dns-addr |sec-dns-addr</p><p>-------------------------+---------------+---------------+-------------</p><p>--+--------------+---------------</p><p>ont:1/1/1/1/8/1 172.17.180.90 255.255.255.0 172.17.180.1</p><p>172.16.180.240 185.228.168.168</p><p>NOTA: Para que o ip-host funcione corretamente, a transmissão deve estar</p><p>habilitada na VLAN</p><p>#configure vlan id 400 new-broadcast enable</p><p>2. Configuração ONT (Modo de acesso – somente IPTV)</p><p>O ONT está conectado à porta 1/1/1 com o ID onu 8 1. Crie a interface</p><p>ONT e configure o estado do administrador</p><p>admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:0002F163</p><p>sw-ver-pland disabled iphc-allowed enable enable-aes disable</p><p>configure>equipment>ont>interface>1/1/1/1/8 admin-state up</p><p>2. Planeje o tipo de slot do cartão e defina a quantidade e o tipo de</p><p>portas (1 ETH no caso de HL-1GE)</p><p>admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type</p><p>10_100base plndnumdataports 1 plndnumvoiceports 0 admin-state up</p><p>NOTA:</p><p>O slot 1 é para placa Ethernet -> #configure equipment ont slot</p><p>1/1/1/1/8/ 1</p><p>3. Crie um perfil de QoS</p><p>#configure qos profiles bandwidth 1G committed-info-rate 0 assured-</p><p>info-rate 0 excessive-info-rate 1000000</p><p>4. Defina a velocidade da porta Ethernet/duplex e atribua o perfil DBA</p><p>admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-</p><p>state up</p><p>admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0</p><p>bandwidth-profile name:1G</p><p>5. Adicione vlan 200 à porta da ponte</p><p>admin>#configure bridge port 1/1/1/1/8/1/1</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 200 tag untagged</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>200$ exit</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1# pvid 200</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1# max-unicast-mac 200</p><p>Lembre-se de habilitar o controle multicast e o encaminhamento na vlan</p><p>200</p><p>admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-</p><p>mcast-ctrl in-qos-prof-name name:Default_TC0</p><p>6. Opcionalmente configure ip-host1</p><p>#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-</p><p>profile name:1G</p><p>#configure bridge port 1/1/1/1/8/vuni</p><p>#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400</p><p>#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400</p><p>#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up</p><p>7. Exibir endereço IP do host 1 do ONT</p><p>#show iphost ont operational-data</p><p>operational-data table</p><p>=======================================================================</p><p>==================================</p><p>index |ip-address |net-mask |default-</p><p>router |dns-addr |sec-dns-addr</p><p>-------------------------+---------------+---------------+-------------</p><p>--+--------------+---------------</p><p>ont:1/1/1/1/8/1 172.17.180.90 255.255.255.0 172.17.180.1</p><p>172.16.180.240 185.228.168.168</p><p>NOTA: Para que o ip-host funcione corretamente, a transmissão deve estar</p><p>habilitada na VLAN</p><p>#configure vlan id 400 new-broadcast enable</p><p>3. Configuração ONT (Modo Transparente – INTERNET, VOIP, IPTV)</p><p>O ONT está conectado à porta 1/1/1 com o ID onu 8 1. Crie a interface</p><p>ONT e configure o estado do administrador</p><p>admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:0002F163</p><p>sw-ver-pland disabled iphc-allowed enable enable-aes disable</p><p>configure>equipment>ont>interface>1/1/1/1/8 admin-state up</p><p>2. Planeje o tipo de slot do cartão e defina a quantidade e o tipo de</p><p>portas (1 ETH no caso de HL-1GE)</p><p>admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type</p><p>10_100base plndnumdataports 1 plndnumvoiceports 0 admin-state up</p><p>NOTA:</p><p>O slot 1 é para placa Ethernet -> #configure equipment ont slot</p><p>1/1/1/1/8/ 1</p><p>3. Crie um perfil de QoS</p><p>#configure qos profiles bandwidth 1G committed-info-rate 0 assured-</p><p>info-rate 0 excessive-info-rate 1000000</p><p>4. Defina a velocidade da porta Ethernet/duplex e atribua o perfil DBA</p><p>admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-</p><p>state up</p><p>admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0</p><p>bandwidth-profile name:1G</p><p>5. Adicione as vlans 100, 200,300 conforme marcadas na porta da ponte</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 100 tag single-</p><p>tagged</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>100$ exit</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 200 tag single-</p><p>tagged</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>200$ exit</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 300 tag single-</p><p>tagged</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>300$ exit</p><p>admin>configure>bridge>port>1/1/1/1/8/1/1#</p><p>max-unicast-mac 200</p><p>Lembre-se de habilitar o controle multicast e o encaminhamento na vlan</p><p>200</p><p>admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-</p><p>mcast-ctrl in-qos-prof-name name:Default_TC0</p><p>6. Opcionalmente configure ip-host1</p><p>#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-</p><p>profile name:1G</p><p>#configure bridge port 1/1/1/1/8/vuni</p><p>#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400</p><p>#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400</p><p>#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up</p><p>7. Exibir endereço IP do host 1 do ONT</p><p>#show iphost ont operational-data</p><p>operational-data table</p><p>=======================================================================</p><p>==================================</p><p>index |ip-address |net-mask |default-</p><p>router |dns-addr |sec-dns-addr</p><p>-------------------------+---------------+---------------+-------------</p><p>--+--------------+---------------</p><p>ont:1/1/1/1/8/1 172.17.180.90 255.255.255.0 172.17.180.1</p><p>172.16.180.240 185.228.168.168</p><p>NOTA: Para que o ip-host funcione corretamente, a transmissão deve estar</p><p>habilitada na VLAN</p><p>#configure vlan id 400 new-broadcast enable</p><p>4. Configuração ONT (Vlan Translation – RBSA)</p><p>O ONT está conectado à porta 1/1/1 com o ID onu 8 1. Crie a interface</p><p>ONT e configure o estado do administrador</p><p>admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:0002F163</p><p>sw-ver-pland disabled iphc-allowed enable enable-aes disable</p><p>configure>equipment>ont>interface>1/1/1/1/8 admin-state up</p><p>2. Planeje o tipo de slot do cartão e defina a quantidade e o tipo de</p><p>portas (1 ETH no caso de HL-1GE)</p><p>admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type</p><p>10_100base plndnumdataports 1 plndnumvoiceports 0 admin-state up</p><p>NOTA:</p><p>O slot 1 é para placa Ethernet -> #configure equipment ont slot</p><p>1/1/1/1/8/ 1</p><p>3. Crie um perfil de QoS</p><p>#configure qos profiles bandwidth 1G committed-info-rate 0 assured-</p><p>info-rate 0 excessive-info-rate 1000000</p><p>4. Defina a velocidade da porta Ethernet/duplex e atribua o perfil DBA</p><p>admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-</p><p>state up</p><p>admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0</p><p>bandwidth-profile name:1G</p><p>5. Adicione as vlans 100, 200,300 conforme marcadas na porta da ponte e</p><p>defina a tradução da vlan</p><p>typ:admin>configure>bridge>port>1/1/1/1/8/1/1</p><p>typ:admin>configure>bridge>port>1/1/1/1/8/1/1# vlan-id 35 l2fwder-vlan</p><p>100 vlan-scope local</p><p>typ:admin>configure>bridge>port>1/1/1/1/8/1/1# vlan-id 838 l2fwder-vlan</p><p>200 vlan-scope local</p><p>typ:admin>configure>bridge>port>1/1/1/1/8/1/1# vlan-id 839 l2fwder-vlan</p><p>300 vlan-scope local</p><p>typ:admin>configure>bridge>port>1/1/1/1/8/1/1 max-unicast-mac 200</p><p>Lembre-se de habilitar o controle multicast e o encaminhamento na vlan</p><p>200</p><p>admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-</p><p>mcast-ctrl in-qos-prof-name name:Default_TC0</p><p>6. Adicione a string de identificação do usuário à VLAN 35 e VLAN 838</p><p>configure interface port vlan-port:1/1/1/1/8/1/1:35 admin-up user</p><p>"00C1777A22#1#01#01:08.01.01"</p><p>configure interface port vlan-port:1/1/1/1/8/1/1:838 admin-up user</p><p>"03#1#01#01:08.01.01"</p><p>7.Adicione uma descrição</p><p>configure equipment ont interface 1/1/1/1/8 desc1 DESCRIPTION</p><p>configure equipment ont interface 1/1/1/1/8 desc2 DESCRIPTION2</p><p>8. Opcionalmente configure ip-host1</p><p>#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-</p><p>profile name:1G</p><p>#configure bridge port 1/1/1/1/8/vuni</p><p>#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400</p><p>#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400</p><p>#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up</p><p>9. Exibir endereço IP do host 1 do ONT</p><p>#show iphost ont operational-data</p><p>operational-data table</p><p>=======================================================================</p><p>==================================</p><p>index |ip-address |net-mask |default-</p><p>router |dns-addr |sec-dns-addr</p><p>-------------------------+---------------+---------------+-------------</p><p>--+--------------+---------------</p><p>ont:1/1/1/1/8/1 172.17.180.90 255.255.255.0 172.17.180.1</p><p>172.16.180.240 185.228.168.168</p><p>NOTA: Para que o ip-host funcione corretamente, a transmissão deve estar</p><p>habilitada na VLAN</p><p>#configure vlan id 400 new-broadcast enable</p><p>5. Configuração ONT (QinQ – INTERNET, VOIP, IPTV – c-VLANs irrestritas)</p><p>Antes da configuração do ONT, defina o empilhamento de VLAN no OLT</p><p>(com C-VLANs NÃO especificadas)</p><p>configure vlan id stacked:999:0 mode residential-bridge in-qos-prof-</p><p>name name:Default_TC0</p><p>O ONT está conectado à porta 1/1/1 com o ID onu 8 1. Crie a interface</p><p>ONT e configure o estado do administrador</p><p>admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:0002F163</p><p>sw-ver-pland disabled iphc-allowed enable enable-aes disable</p><p>configure>equipment>ont>interface>1/1/1/1/8 admin-state up</p><p>2. Planeje o tipo de slot do cartão e defina a quantidade e o tipo de</p><p>portas (1 ETH no caso de HL-1GE)</p><p>admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type</p><p>10_100base plndnumdataports 1 plndnumvoiceports 0 admin-state up</p><p>NOTA:</p><p>O slot 1 é para placa Ethernet -> #configure equipment ont slot</p><p>1/1/1/1/8/ 1</p><p>3. Crie um perfil de QoS</p><p>#configure qos profiles bandwidth 1G committed-info-rate 0 assured-</p><p>info-rate 0 excessive-info-rate 1000000</p><p>4. Defina a velocidade da porta Ethernet/duplex e atribua o perfil DBA</p><p>admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-</p><p>state up</p><p>admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0</p><p>bandwidth-profile name:1G</p><p>5. Adicione S-VLAN como VLAN 888 empilhada</p><p>typ:admin>configure>bridge>port>1/1/1/1/8/1/1 max-unicast-mac 200</p><p>vlan-id stacked:888:0</p><p>tag single-tagged</p><p>exit</p><p>pvid stacked:888:0</p><p>Lembre-se de habilitar o controle multicast e o encaminhamento na vlan</p><p>200</p><p>admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-</p><p>mcast-ctrl in-qos-prof-name name:Default_TC0</p><p>6. Opcionalmente configure ip-host1</p><p>#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-</p><p>profile name:1G</p><p>#configure bridge port 1/1/1/1/8/vuni</p><p>#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400</p><p>#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400</p><p>#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up</p><p>7. Exibir endereço IP do host 1 do ONT</p><p>#show iphost ont operational-data</p><p>operational-data table</p><p>=======================================================================</p><p>==================================</p><p>index |ip-address |net-mask |default-</p><p>router |dns-addr |sec-dns-addr</p><p>-------------------------+---------------+---------------+-------------</p><p>--+--------------+---------------</p><p>ont:1/1/1/1/8/1 172.17.180.90 255.255.255.0 172.17.180.1</p><p>172.16.180.240 185.228.168.168</p><p>NOTA: Para que o ip-host funcione corretamente, a transmissão deve estar</p><p>habilitada na VLAN</p><p>#configure vlan id 400 new-broadcast enable</p><p>6. Configuração ONT (QinQ – INTERNET, VOIP, IPTV – c-VLANs restritas)</p><p>Antes da configuração do ONT, defina o empilhamento de VLAN no OLT</p><p>(com C-VLANs especificadas )</p><p>configure vlan id stacked:999:100 mode residential-bridge in-qos-prof-</p><p>name name:Default_TC0</p><p>configure vlan id stacked:999:200 mode residential-bridge in-qos-prof-</p><p>name name:Default_TC0</p><p>configure vlan id stacked:999:300 mode residential-bridge in-qos-prof-</p><p>name name:Default_TC0</p><p>O ONT está conectado à porta 1/1/1 com o ID onu 8 1. Crie a interface</p><p>ONT e configure o estado do administrador</p><p>admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:0002F163</p><p>sw-ver-pland disabled iphc-allowed enable enable-aes disable</p><p>configure>equipment>ont>interface>1/1/1/1/8$ admin-state up</p><p>2. Planeje o tipo de slot do cartão e defina a quantidade e o tipo de</p><p>portas (1 ETH no caso de HL-1GE)</p><p>admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type</p><p>10_100base plndnumdataports 1 plndnumvoiceports 0 admin-state up</p><p>NOTA:</p><p>O slot 1 é para placa Ethernet -> #configure equipment ont slot</p><p>1/1/1/1/8/ 1</p><p>3. Crie um perfil de QoS</p><p>#configure qos profiles bandwidth 1G committed-info-rate 0 assured-</p><p>info-rate 0 excessive-info-rate 1000000</p><p>4. Defina a velocidade da porta Ethernet/duplex e atribua o perfil DBA</p><p>admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-</p><p>state up</p><p>admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0</p><p>bandwidth-profile name:1G</p><p>5. Adicione S-VLAN como VLAN 888 empilhada</p><p>typ:admin>configure>bridge>port>1/1/1/1/8/1/1</p><p>max-unicast-mac 200</p><p>vlan-id 100</p><p>tag single-tagged</p><p>l2fwder-vlan stacked:999:100</p><p>vlan-scope local</p><p>exit</p><p>vlan-id 200</p><p>tag single-tagged</p><p>l2fwder-vlan stacked:999:200</p><p>vlan-scope local</p><p>exit</p><p>vlan-id 300</p><p>tag single-tagged</p><p>l2fwder-vlan stacked:999:300</p><p>vlan-scope local</p><p>exit</p><p>Lembre-se de habilitar o controle multicast e o encaminhamento na vlan</p><p>200</p><p>admin>#configure id stacked:999:200 mode residential-bridge ipv4-mcast-</p><p>ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0</p><p>6. Opcionalmente configure ip-host1</p><p>#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-</p><p>profile name:1G</p><p>#configure bridge port 1/1/1/1/8/vuni</p><p>#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400</p><p>#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400</p><p>#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up</p><p>7. Exibir endereço IP do host 1 do ONT</p><p>#show iphost ont operational-data</p><p>operational-data table</p><p>=======================================================================</p><p>==================================</p><p>index |ip-address |net-mask |default-</p><p>router |dns-addr |sec-dns-addr</p><p>-------------------------+---------------+---------------+-------------</p><p>--+--------------+---------------</p><p>ont:1/1/1/1/8/1 172.17.180.90 255.255.255.0 172.17.180.1</p><p>172.16.180.240 185.228.168.168</p><p>NOTA: Para que o ip-host funcione corretamente, a transmissão deve estar</p><p>habilitada na VLAN</p><p>#configure vlan id 400 new-broadcast enable</p><p>Tradução site : https://halny.com/knowledge-base/halny-hl-1ge-sfu-configuration-nokia-7360/</p><p>https://halny.com/knowledge-base/halny-hl-1ge-sfu-configuration-nokia-7360/</p><p>Configuração SFU HALNy HL-1GE/HL-1GE2 [NOKIA 7360]</p><p>Cenário de serviço</p><p>Comutação de modos ONT HGU<->SFU</p><p>Cenário de serviço SFU suportado e configuração ON</p><p>1. Configuração ONT (Modo de acesso – somente INTE</p><p>2. Configuração ONT (Modo de acesso – somente IPTV</p><p>3. Configuração ONT (Modo Transparente – INTERNET,</p><p>4. Configuração ONT (Vlan Translation – RBSA)</p><p>5. Configuração ONT (QinQ – INTERNET, VOIP, IPTV –</p><p>6. Configuração ONT (QinQ – INTERNET, VOIP, IPTV –</p>