Prévia do material em texto
Frictional forces
8. Currents and Frictional
Forces, Horizontal
Wind-Driven Currents,
Thermohaline Circulations
The currents discussed in the preceding chapter
were assumed to be frictionless or, at least, not
essentially affected by frictional forces. Without
friction, the non-accelerated horizontal motion on
the rotating earth is perpendicular to the horizontal
pressure gradient; thus it follows the direction of
isobars. Observations in the ocean as well as in the
atmosphere have shown that this is approximately
true only in the deeper layers of the sea or in higher
altitudes of the atmosphere. Deviations from the
direction parallel to the isobars occur near the sea
surface and near the bottom as a result of increased
boundary friction. However, even far away from
boundaries, strictly frictionless currents never exist
in nature because water, like any other fluid or
gas, is a viscous matter and is affected by molecular
friction. For sea water, molecular viscosity was
considered in Chapter 3; viscous flow of a com¬
pressible fluid on a non-rotating earth was dis¬
cussed in Chapter 6.
Since the motions in the oceans and in the atmos¬
phere are turbulent rather than laminar, “eddy
viscosity” effects play a more significant part in
controlling stresses or friction between adjacent
layers of a fluid moving with different velocities
relative to each other. Smaller or greater amounts
of water are carried by irregular random turbulent
motion from one layer into another, thus tending
to equalize relative velocity differences in both the
lateral and the vertical direction by momentum
transfer.
The origin of turbulence has not yet been fully
explained. Often, the molecular viscosity coeffi¬
cient, |u, is simply replaced by a much greater “eddy
viscosity coefficient,” A, in Newton’s formula [eq.
(3.35)] for the shearing stress r. Thus, for turbulent
motion
on (8.1)
where cs is the velocity component in the direction
s and n is a direction perpendicular to s. The values
of A in turbulent motion may vary over wide
ranges, from the order 1 or less through 10R [cm'1
gr sec-1], depending upon the scale of the motion
(vertical, horizontal, large-scale, or small-scale
motion), on the stratification of water masses, and
other factors that are not yet clearly understood.
It seems that the breaking of waves in the surface
layers of the sea has a significant effect on the value
of the “eddy viscosity coefficient”; with greater
“wind stirring” of the surface layers the eddy vis¬
cosity coefficient increases. Some numerical values
184
for different wind speed were given by Thorade
(1914) and Neumann (1952).
The concept of “eddy viscosity” was first used in
ocean currents by Ekman (1902), and in the
atmosphere by Schmidt (1917).
A simpler assumption about the virtual internal
friction was introduced earlier by Guldberg and
Mohn (1876) for atmospheric motions. In their
time it was known that, for example, in the case
of cyclonically curved isobars the air actually flows
into the region of lower pressure. Thus, an acceler¬
ation in the direction of the pressure gradient must
be expected. The fact that in spite of this no real
acceleration occurs indicates that an “apparent”
force is at work and that force can only be friction.
Guldberg and Mohn made the simple, but for some
purposes quite successful, assumption that this
frictional force is proportional to the current ve¬
locity. In a first approximation they assumed that
R = prc (8.2)
where R is the frictional force, c the velocity of
the current, p the density, and r [sec-1] a propor¬
tionality factor, the coefficient of virtual internal
friction, which should not be confused with A in
eq. (8.1). At the time, the Guldberg-Mohn assump¬
tion marked a great step forward; the angle of
departure between the geostrophic flow and the
actual flow was explained in a simple way, as
illustrated in Figure 8.1, where the pressure gradient
force G, is balanced by the resultant of the Coriolis
force, CF, and the frictional force, R, thus provid¬
ing an unaccelerated motion with the velocity c,
which flows from high to low pressure areas.
In Figure 8.1, ct is the angle between the pressure
gradient and the current direction; thus
tan a
CF __ 2co sin
~R ~ ' 7~ (8.3)
The simple Guldberg-Mohn assumption has often
P\~bp
P\
Figure 8.1 Modification of balance of forces in a
geostrophic flow by a frictional force, R, acting in the
opposite direction to the current vector, c. High and
Low indicate high and low pressure areas, respectively.
Compare this figure with Figure 7.20.
been used as a first approximation in estimating
frictional effects in the atmosphere and in the
ocean. Because the angle of departure, a, for
unaccelerated currents as in Figure 8.1, is in some
way related to the “virtual internal friction,” R
can at least be approximated by a numerical
value R = Coriolis force/tan a, or r = 2co sincondition requires that the divergence
of the total horizontal mass transport between the
surface and the bottom vanish. The geostrophic
deep current is, according to Ekman, non-diver-
gent. If the x-axis is parallel to the coast and in
the direction of the deep current and the wind
stress, rx, the continuity equation reduces to
Sy + My = + -°2^ - 0 (8.65)
where Sv and My are the mass transports in the
surface layer and bottom layer, respectively, ac¬
cording to eqs. (8.50) and (8.63) for d > D* + D.
Thus, the velocity of the geostrophic deep current
ug, or the slope /3 of isobaric surfaces, can be com¬
puted from eq. (8.65) if the wind stress, tx, and the
depth D* are known;
2 7CTX
pD*f (8.66a)
The slope of the sea surface perpendicular to the
coast is
$ '^7t pgD* (8.66b)
It the depth d is small as compared with the
depth D* + D, the mass transport components
have to be computed from eqs. (8.53) and (8.62)
to find the structure of the vertical current distribu¬
tion and the slope of the sea surface. Ekman (1905)
has given several examples for this case and also
considered the fact that the wind may form an
angle other than zero degrees with the straight
coast line. It follows from Ekman’s results that, if
the total depth d is smaller than D* + D the deep
current is missing, and the bottom and surface
currents pass into each other with a distortion of
the characteristic form in deeper water. Examples
(2)-(4), (6)—(8), and (10)—(12) in Figure 8.13 de¬
monstrate the effect of decreasing water depth when
winds are blowing from different directions toward
the coast. Examples(13)-(15)in Figure 8.13 illustrate
the case when the wind blows offshore. The total
flow in the pure drift current is directed parallel
to the coast if djD is large enough and no deep
current or bottom current is present. The wind
direction with respect to the coastline is of great
importance, except when the depth dis considerably
smaller than D* + D. In this case the earth’s
rotation is of little influence.
The relationship between wind direction with
respect to the coast and the velocity and direction
of the surface water is very simple in the case of
deep water. Ekman (1905) has given a convenient
graphical method for the construction of the sur¬
face current vector near the coast.
For deep water the total mass transport of the
pure drift current is perpendicular to the wind
direction and, according to eq. (8.50), equal to
P(V0D/7c+/~2 ). Let the_y-axis be parallel to the wind
direction, and let a be the angle between the coast
and the wind direction, taken positive to the right
of the wind. Then, the mass transport of the pure
drift current perpendicular to the coast is S cos a,
which must be equal to the mass transport pro¬
duced by the slope current in the opposite direction
[eq. (8.63)]. Thus
VnD D* g 8 —7— cos a = -j-
7tv 2 47rco sin
thus
V0D
cos a
D*
'lit Uq 7t+/ 2
and with D = D*
ua = K V 2 COS a
With this, Ekman obtains the simple graphical con¬
struction of the surface current as shown in Figure
8.14.
202 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
Figure 8.13 Examples of the vertical structure of Ekman’s elementary current
system in coastal regions, projected on a horizontal plane. [From Ekrnan (1905).]
Draw the line OA, inclined by 45° against the
x-axis, and let OA = V0 be the velocity of the pure
surface drift current. Next, draw a line ACB parallel
to the y-axis in the wind direction. The circle
through A around C will have the y-axis at x — 0
tangent in the point E. The diameter of the circle
is AB = 2 . Let any arbitrary coastline direc¬
tion be given by AD, with the angle a between the
wind and the coast line; then AD = AB cos a
represents the direction and magnitude of the deep
current. OA = V0 is the surface current of the pure
drift current alone, and the resultant of OA and
AD is consequently the true surface current vector
OD in Figure 8.14.
The depths D and D* at a given geographical
latitude depend on the coefficient of eddy viscosity
in the upper and lower layer of frictional influence,
respectively. Inadequate knowledge of the character
of turbulent frictional forces in the ocean as well
as in the atmosphere makes a direct application of
Ekman’s equations difficult. In more realistic
Figure 8.1 4 Geometrical construction of surface
current direction and speed near a straight coast for
deep water at different angles, a, between wind and
coast. [After Ekrnan, (1905).]
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 203
204
models frictional forces resulting from lateral
shearing stresses also have to be considered.
Ekman’s deep current is a geostrophic current only
in a first approximation.
Ekman (1923) estimated the thickness of the
upper layer of frictional influence as D = 600
[sec] V0, where V0 is the surface velocity of the pure
drift current [eq. (8.49)]. With the assumption that
frictional forces in the bottom and surface layers
are similar, the thickness of the lower layer of
frictional influence is D* = 600 [sec] G, where G
is the velocity of the deep current regardless of its
direction.
The Elementary Current System in a Closed Sea
Ekman (1905) also considered the case of a closed
sea of constant depth, with a wind of constant
velocity and direction blowing over it. In this case
the total mass transport between surface and bottom
must be zero in every direction when steady motion
has been established. This requires that Sx + Mx
= 0 and Sy + My = 0. If d > D* + D, as in the
preceding example, it is possible to distinguish the
three layers of an elementary current system. The
deep current velocity will, however, be much
smaller than in the case of an infinitely long,
straight coast. It also follows that the deep current
velocity decreases as the total water depth increases.
To simplify the analysis of this problem, orient
the xy-plane with its y-axis in the wind direction.
Then rx — 0, ry = r, and the total mass transport
of the pure wind drift current is Sx — t//. The mass
transport of the slope current, that is, the deep
current plus the bottom current, is obtained from
eqs. (8.63) and (8.64). Since in this problem it is
not known in which direction the pressure gradient
will point, assume that in a rectangular £-77 coordi¬
nate system 77 is the direction of the pressure
gradient, /3, and that the £-axis is perpendicular to
7] (Figure 8.15). Thus
Ms
D*Pgf3
2nf
(8.67)
Mn = D~2^f (8.68)
according to eqs. (8.64) and (8.63). For abbrevi¬
ation put
B =
pgD*
2 nf
and b = B^W~x) (8-69)
Then, = b/3 is the mass transport in the direc¬
tion of the deep current, and Mv = B/3 is the mass
transport in the direction of the pressure gradient.
With an arbitrary orientation of the xy-coordinate
system, where the wind blows in the y-direction
Figure 8.1 5 Direction of slope current transport,
M, in an enclosed sea with respect to the pressure
gradient, P. The upper diagram is for the case where
the water depth is 1.75 times the depth of the layer of
frictional influence {d/D* = 1.75); the lower diagram
applies to the case where the water depth is 0.4 times
the depth D* {d/D* = 0.4). Mv is the component of
anisobaric transport in the direction of the pressure
gradient and is the component in the isobaric di¬
rection. Note the decrease of M and its stronger de¬
flection from the isobaric direction, f, with a decreas¬
ing d/D*, although the slope P for d/D* = 0.4 is
greater than for d/D* = 1.75.
over an enclosed sea, the mass transport compo¬
nents in the slope current are
Mx = B/3X + b/3y
(8.70)
My = B/3V - b/3x
where /3X and (3V denotethe .v- and y-components
of the total pressure gradient, (3, in the direction 77.
From the condition that the net mass transport in
every direction vanishes with steady-state motion,
it follows from + Mx = 0 and Sy + My = 0
that
~j + Bftx + b/3y = 0
B/3y — b/3x = 0
(8.71)
This yields for the x- and y-components of the
pressure gradient
and
/S.r =
/% =
1 Bt
JWTW)
1
7 (B2 + 62)
@y o = — tan ol
(8.72)
(8.73)
where a represents the angle {cum sole) between the
direction of the transport of the slope current and
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
the pressure gradient. If d/D* is large enough the
angle oi is close to 90°. This means that the isobaric
slope and, therefore, the sea surface slope is nearly
in the wind direction. The total slope of the sea
surface /? = (/9| + /32)1/2 is, according to eqs. (8.72)
and (8.73)
,q __t _ sin a r
' + fb
cos a t
~fB
(8.74)
If d/D* is large, a = 90°, approximately, and
/3~
T ^ T
fb ' pgd
(8.75)
Equation (8.75) can be used to compute the station¬
ary slope of a sea surface in an enclosed water body
of constant depth with a (constant) wind blowing
over the surface. Indeed, eq. (8.75) is the simplest
and most basic equation for “storm surge” predic¬
tion.
The velocity of the deep current, G, is obtained
from /3
G=f/3 = ^fL (8.V6)
according to eq. (8.74), and its direction is deflected
from the wind direction by the angle a (contra
solem). If D + £>*, a = 90°, and
The direction of the deep current in sufficiently
deep water is nearly in the wind direction.
In summary, it follows that in an enclosed sea
of sufficiently deep water with a constant wind the
pure drift current is very similar to the current in
an open (unbounded) ocean, while the deep cur¬
rent and the bottom current are relatively weak.
This is illustrated in Figure 8.16, for different
depths, d, according to Ekman. The arrows indicate
the direction of the (rising) slope of the sea sur¬
face in an enclosed sea, with the wind blowing along
the positive p-axis. Thus, the pressure gradient is
almost independent of the Coriolis force and its
value decreases slightly with increasing total (con¬
stant) depth of the sea. Observations in the Baltic
Sea, collected by Colding (1881) after the storm
surge in November 1872, have essentially con¬
firmed Ekman’s results.
The transient state: development of
wind drift currents from state of rest
Ekman has also investigated the transient state in
the development of the elementary current system.
Of special interest is the question of how long it
would take for a pure wind drift current and a
slope current to establish stationary or nearly sta¬
tionary conditions.
Pure Drift Currents
In the case of pure drift currents again an un¬
bounded, infinitely deep ocean is assumed, origi¬
nally at rest. At the time t — 0 assume that a con¬
stant wind suddenly begins to blow in the positive
^-direction, exerting the wind stress, rv, at the sea
surface. From the equations of motion for acceler¬
ated flow it follows that
dw . „ 82w _ + ;^vv=_ (8.78)
where w = u + iv as in eq. (8.42). The initial and
boundary conditions are
8u
dz
= 0
dv _ Ty
dz A
u = v = 0
■ for z — 0
for z = co
(8.79)
/ / y
Figure 8.1 6 Vertical structure of Ekman’s elementary current system in an
enclosed sea projected on a horizontal plane. The arrows indicate the direction of
the upward slope of the sea surface with winds blowing along the positive jr-axis.
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 205
The solution of eq. (8.78) with the conditions of
eqs. (8.79), as given by Fredholm, will not be ex¬
plicitly stated in this book. Reference is made to
Ekman (1905). Figure 8.17 illustrates the evaluation
of Fredholm’s solution for the surface current at
z = 0, and the currents at depths z = 0.5D, z = D,
and z = 2D, where D is the depth of the layer of
frictional influence [eq. (8.46)]. The time is ex¬
pressed in hours of a pendulum day.t
The current vectors in Figure 8.17, during dif¬
ferent stages of the development of a pure drift
current, are to be drawn from the origin of the
.vy-coordinate system to the spiral curves. Thus, in
the transient stage the end point of the surface
current vector rotates around the center point
of the spiral, which represents the end point of
the stationary current vector. Each turn of the
damped circular oscillation around the center is
completed in 12 pendulum hours. Except in the
immediate proximity of the equator, pure drift
currents follow wind fluctuations almost instan¬
taneously. The average velocity during a pendulum
day is very nearly the same as in a stationary drift
current, but the oscillations around the stationary
motion will continue for serveral days, especially
in the deeper layers where the oscillations at first
grow before they start to decrease. The oscillations
around the stationary state show the characteristic
inertia currents with equal phase at different depths.
In shallow water the stationary state of motion
will be established more quickly than in the case
of infinitely deep water. Solutions for a gradually
increasing or decreasing wind have been given by
Hidaka (1933), Nomitsu (1933), and F. Defant
(1940).
Slope Currents
The transient stage in the formation of a slope
current was also studied by Ekman (1905). When
the inclination of the sea surface produced by the
wind rises gradually, the periodic inertia motion
superimposed on the deep current is less pro¬
nounced than in the case of a sudden appearance
of a sea surface slope. If, for example, sin fi =& ft
increases uniformly with time, Ekman assumes that
g/3 = «t where k is a constant. In the absence of
friction
du dv „ . ,
di = 2a) sin 0 v; = -2a sin 0 u + Kt (8.80)
Figure 8.17 Hodographs showing the develop¬
ment of a pure drift current (infinitely deep ocean)
with time at different depths. The depth, z, is given in
terms of the thickness of the upper layer of frictional
influence, D, and the time in pendulum hours after
the start of a constant wind. [After Ekman (1905).]
fA pendulum day is the time required by a Foucault
pendulum to make one complete revolution of its plane of
oscillation. The pendulum day is equal to a sidereal day
(23 hours 56 minutes 4.09 seconds) divided by the sine of
the latitude.
With u = v = 0 for t = 0, the solution of eq. (8.80)
is
U ~ 4a2 sin2 [1 ~ cos (2tw sin ^
The velocity curve (hodograph) of the motion
represents a cycloid, each branch being described
every 12 pendulum hours. Thus, if the rise of the
slope takes place over two or more days, the peri¬
odic oscillations of the deep water velocity vector
are small as compared with the total velocity,
which is nearly perpendicular to the gradient. The
total motion of the water in the direction of the
force is
_•si _ g/da
4a'2 sin2 4a2 sin3 D -f- D*, bounded by an in¬
finitely long straight coast extending in the y-
direction. With the wind blowing in the y-direction,
a slope, ft, of the sea surface perpendicular to the
coast will gradually build up as a result of the
water transport in the upper layer of frictional
influence. Let ft0 be the final (stationary) slope of
the sea surface f = f(x, t)\ then sin ft0 = 8%0/dx.
If 5 represents the net water transportper second
toward the coast across a vertical plane of unit
width (Ay = 1), the water surface will rise during
the time interval 8t by the amount of Sf = (d£/8t)8t.
Between the coast and the distance x from the
coast, the water volume (per unit width)
dx
has been added. This must be equal to the total
transport, — S8t, during this time interval 8t. Thus
-S =
xd£
o dt
dx
ds = d£
dx 8t
(8.83)
With a stationary sea surface slope ft0, the water
volume transported by the pure drift current per¬
pendicular to the coast is S0. The same volume is
carried away from the coast by the stationary
bottom current. Thus, Ekman assumed that, ap¬
proximately
5 = So
/3q—/3
fto
and, according to eqs. (8.83)
S,dft = K
/30 dx dt
(8.84)
Since /3 — 8%/8x, eq. (8.85) is obtained from (8.84).
Sn d'2 ft __ d2£ dj3
fto dx2 dxdt dt
(8.85)
The initial and boundary conditions are that
ft = 0 for t — 0
and that (8.86)
ft = fto for x = 0 (at the coast)
If we assume that the ocean is unbounded in the
positive x-direction, the differential equation (8.85)
is equivalent to a well-known equation in the theory
of heat conduction. Its solution is
P(x) =
V 7t I'
dx
represents a minor variant of the probability
function.
If d is sufficiently large by comparison to the
depth, D + D*
S -D D**&
0 ? 4ttco sin
(8.88)
according to eq. (8.63).t
Since P(x) for x sin cf) x /0
ir=1JvwT (8-89)
From eq. (8.89), Ekman computes that 70 per cent
of the final slope ft0 is attained in the time
'■= 0 00022 ZTiTHTJ--(8.49). The wind
stress, r, is usually expressed in terms of a resistance
coefficient, C, and the wind speed, w, as shown in
eq. (8.92) where p' is the density of the air.
T = p'Cw2 (8.92)
(■According to the Beaufort Scale for wind velocities, 4-5
Beaufort corresponds to about 8.5 m/sec wind velocity
measured at about 10 meters above the water surface.
left, of the wind direction, depending on whether
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
This equation is based on hydrodynamic reason¬
ing, and the value of C refers to a given wind speed
at “anemometer height,” usually 6 to 8 meters
above the water surface. The coefficient C depends
on the hydrodynamic character of the underlying
surface. In the case of a flow over rough surfaces
the resistance coefficient varies with the hydro-
dynamic roughness of the surface. For a flow over
water surfaces, allowance has to be made for the
fact that the sea surface roughness can vary with
the wind speed (wave motion). Thus, C should not
be considered as a constant but as a function of
the wind speed. Equation (8.92), when applied to
the wind stress at water surfaces, can then be
expressed in the form
t = p'C(w)w2 = p'C*wn (8.93)
where C* is a constant, and the exponent n will
probably be different from 2. Attempts to deter¬
mine the numerical value of n as well as of C*
have been made by various investigators using
different methods. If C, according to eq. (8.93),
is expressed by C(w) = t/p'w2 and related to the
wind speed, w, at a height of about 6 meters, some
of the results obtained by different methods are
summarized in Figure 8.18. It is seen that a con¬
siderable disagreement exists regarding the rela¬
tionship between the resistance coefficient C(w) and
the wind speed, especially at low wind velocities.
On the basis of sea surface slope observations,
Neumann (1948) suggested C(w) = 9 X 10“3w_1/2
where w is in meters per second, and therefore
t = 0.9 x 10~3p'w312 (8.94)
In considering the difficulties involved in wind
stress determinations, and in view of the discrep¬
ancies between the results obtained from different
methods, many investigators prefer the quadratic
law
t = 2.6 X 10-3p'w2 (8.95)
which first was applied by Ekman. Palmen and
Data.:
Results of sea surface slope observations
Results of vertical wind profile
measurements
0^ collected by Neumann (1948; 1951)
• Keulegan (1952), Lake Erie
Q Hellstrom (1953), Ringkobing Fjord
O Roll (1948); (uncorrected)
+ Roll (1952)
Figure 8.1 8 Resistance coefficient, C, of the sea surface as a function of the
wind velocity, w, m/sec (anemometer height 6 meters). Since the preparation of
this figure, other forms for the drag coefficient have been proposed (see Figure
13.12). Recent observations at Argus Island by P. DeLeonibus (Trans. Amer.
Geophys. U., Vol. 46, No. 1 (1965) p. 98.) have shown that C can decrease as
well as increase with wind speed depending on the Richardson number.
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 209
Laurila (1938) obtained a similar relationship with
the factor 2.4 instead of 2.6 in eq. (8.95) and Hela
(1948) found r = 1.9 X 10‘3 w2.
The uncertainty of the wind stress-wind relation¬
ship, in addition to the poor knowledge of the
value of eddy viscosity coefficients and their de¬
pendence on wind speed, makes it very difficult
to evaluate eq. (8.49) for the surface drift cur¬
rent velocity, V0. Thorade (1914) studied this re¬
lationship empirically on the basis of carefully
selected current observations in different latitudes.
He was able to confirm the dependence of V0
on the geographical latitude, . According to
Thorade
2.59 */w
Vsin cf>
for w ^ 6 m/sec (approximately)
K =
1.26 w
-s/sin cf>
for w > 6 m/sec
where V0 is given in cm/sec if w is measured
in m/sec. Palmen (1931) argued that Thorade’s
relationship for w ^ 6 m/sec is not well enough
established due to uncertainties in the conversion
of the Beaufort scale into m/sec. Palmen used obser¬
vations at Finngrundet lightship (61°N) and sug¬
gested V0 [cm/sec] = 1.4 w [m/sec] for a latitude of
61°. However, his results apply to shallow water
bodies (Baltic Sea). Durst (1924) obtained for cur¬
rents in the open ocean
y _ 0.79w
0 ^/sin (8 98)
Vsin 9
With the assumption that these expressions are
fairly accurate, the eddy viscosity coefficient A in
eq. (8.46) can be estimated. It follows from eqs.
(8.98) and (8.97) that
A =& 1.02 (if)3 for w 6 m/sec
These estimates can only be considered as crude
approximations. Even if fairly reliable, they are
only applicable in the very surface layers of the
ocean. Schmidt (1917) derived from Thorade’s drift
current observations the following values.
w m/sec 1 3 5 7 10 15 20
A g/cm sec (1) 28 110 220 430 1000 1720
Durst (1924) made some calculations of the eddy
viscosity coefficients for various regions in the
three oceans, based on observations at wind speeds
between 7.5 and 9.8 m/sec. His averaged results
for six regions are given below (n is the number of
observations in each region).
Region
47°-53°N 10°-20°N 10°-20JS 20°-30°S 20 -30 S 30’-40’S
10°-30°W 150°-170UW 90°-l 10°E 100°-105°E 100°-170°W 40°-l 10°E
Alp [cm2/sec] 613 248 993 604 1310 398
n 147 56 44 48 32 121
210 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
From estimates of an energy balance in fully
developed, wind-generated waves, Neumann (1952)
derived values for eddy viscosity coefficients that
agree fairly well with the results obtained by
Thorade, Schmidt, and Durst (Figure 8.19).
In 1952, Ekman published a detailed study on
ocean currents, based on measurements made
during a cruise on board the Research Vessel
Armauer Hansen in 1930. He shows “how pre¬
carious an attempt towards a strictly quantitative
verification of the theory of drift currents may
be.” His conclusions with regard to his theoretical
results, essentially obtained in 1905, are:
The final result of the investigation may be summed
up by saying that the observations made are not
sufficient to establish definitely the existence of a
“pure drift current” as demanded by theory, but that
they are consistent—and in some respects even show
a remarkable agreement—with the theoretical char¬
acteristics of such drift currents.
Basic Equations of the Storm Surge Problem
The piling up of water against coasts under the
action of wind (Windstau) becomes of special
practical importance in relatively shallow water
with strong onshore winds. The rise of the water
level can be considerable, and inundations of
coastalregions have caused great losses of lives
and property. Along the east coast of North
America and in the Gulf of Mexico, storm surges
associated with hurricanes are most dangerous.
Practical methods for storm surge prediction are
largely based on statistical studies. Empirical re¬
lationships have been developed between the
change in sea level and meteorological factors such
as air pressure distribution, wind speed, fetch,
duration of wind action, and effective bottom
topography. One of the more recent studies of this
kind, developed for the Gulf and East Coast of
the United States, is the method proposed by
Harris (1959).
The basic equation that relates the slope, /3, of
the sea surface to the wind stress is essentially of
the form
j3 = X—,r (8.100)
^ gpd
This is Ekman’s equation for a stationary slope in
an enclosed sea. The coefficient A decreases with
increasing depth d from the value f- to 1. Thus,
with d^> D*, A —> 1 and eq. (8.75) is obtained.
With very shallow water, or neglect of the Coriolis
3000
2000
1500
1000 -
600-
400
300
- 200
E
O
100
60
40
20
10
Figure 8.1 9 Comparison of eddy viscosity coeffici¬
ents, A, in the surface layer of the sea at different wind
velocities (m/sec) obtained by different methods.
force, A — -f. If Coriolis forces in shallow water
are also considered, their effect is of little impor¬
tance. The direction- of the maximum slope /3 is
deflected from the wind direction by a relatively
small angle only (10° or less). It is, however, im¬
portant to note that these results of Ekman are
based on the assumption of an eddy viscosity
coefficient which remains constant with depth.
It seems reasonable to assume that the eddy
viscosity coefficient decreases with depth. Palmen
(1932, 1933) has computed the slope of the sea
surface with a variable eddy viscosity coefficient.
Following Fjeldstad and Sverdrup (1929), Palmen
assumed
A=A0(l (8.101)
A0 is the eddy viscosity coefficient at the sea sur-
30
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 211
face, d is the depth, and e is a very small positive
number as compared with d. The exponent n is
positive and smaller than 1.
If the earth’s rotation is neglected and a variable
coefficient A(z) is assumed, according to eq. (8.101),
eqs. (8.54) become
^(-4W§j)+w3 = °
(8.102)
= 0
where the y-axis points in the direction of the slope
of the sea surface /3 = (\/gp)(dp/dy). The bound¬
ary conditions are
r = —A = o, at z = 0
dz dz
(8.103)
u = v = 0, at z = d
For stationary slopes the continuity equation re¬
quires that
d
v dz = 0
o
With eqs. (8.101) and (8.103), the solution of eqs.
(8.102) yields the slope of the sea surface
/3 = 2^7(3-”) (8-104>
when small-order terms are omitted. It follows that
the slope of the sea surface is independent of the
absolute value of the eddy viscosity coefficient and
depends only on the change of the coefficient in
the vertical direction.
The case n = 0 presents a constant A and yields
/3 = (3/2)(jjpgd). This equation was derived by
Ekman (1905) with the neglect of Coriolis forces.
It agrees with eq. (8.100) when X = -§.
The case n = 1 represents a linear decrease of
A towards the bottom, and X = r/pgd. This agrees
with eq. (8.75) for deep water, where A = constant
but where Coriolis forces are considered. The case
0 1, /3
would probably be too large. It seems that in
shallow water or near shore regions the influence
of the Coriolis force and frictional forces may
roughly cancel each other; the error, made with
the assumption that /c = 1, would be small, espe¬
cially in shallow water bodies such as the Baltic Sea
(Palmen, 1936). At least it follows from Ekman’s
fundamental theory that 0 can be considered to be
inversely proportional to the depth d and directly
proportional to the wind stress r.
A simple example illustrates the direct appli¬
cation of eq. (8.105). Consider a basin of constant
depth d and of length / in the direction, x, of the
wind (Figure 8.20). With the z-axis pointing posi¬
tively upward from the bottom, z0 represents the
height of the sea surface over the bottom; with no
wind blowing, z0 — d — constant. Under wind
Figure 8.20 The slope of the sea surface of a water
body of depth d and length / expressed by the denivel-
lation f = z0 — d. The nodal line f = 0 is found at xn.
action the sea surface must slope, and the local
depth z0 depends on x. Under the wind effect
(denivellation) the sea surface f = z0 — d. With
/3 = dz0/dx, and considering that the local depth
z0 = f + d varies with d, eq. (8.105) must be
written
dz0 _ KT
dx ~ gpz0
Integration yields
(8.106)
z0=J ^1(X + C]) (8.107)
where Cj is a constant. Thus, the water surface
assumes a parabolic shape. At a certain distance
x„ from the leeward shore, z0 = d. The coordinate
xn of this point (the nodal line) is obtained from
z0 — d = 0, and
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
god'1
x-=2^T~C i (8.108)
It follows that the position of the nodal line
depends on the wind stress. The constant C, can
be determined from the condition that the volume
of water is constant, or
Substituting eq. (8.107) into eq. (8.109), it follows
that
(/ + C,)3'2 - Cf = (8.110)
The equation has to be solved for C\ by the method
of trial and error, or geometrically.
The computation of the slope of the sea surface
is simpler if variations in depth due to the denivel-
lations of the surface are neglected. This can be
done if ffor the numerical pre¬
diction of storm surges (See Chapter 12.)
Horizontal circulation of wind-driven currents
Homogeneous Ocean
Further studies by Ekman (1923, 1928, 1932) were
directed toward the calculation of the total oceanic
current system for a given wind field of variable
direction and strength. In 1923, Ekman deduced
some important laws that, for the case of steady
motion in particular, the curl of the deep current
must obey. Essential problems were solved, and
the results belong to our basic knowledge in dy¬
namic oceanography. Of special importance are
Ekman’s investigations of the effects of non-
uniform wind systems, of a variable depth and of
a variable Coriolis parameter (variable latitude) on
the horizontal circulation of wind-driven currents.
The kinematic condition for a stationary current
system is that the total transport of water, Q,
between the sea surface and the bottom of the
current satisfies
div Q = 0
The dynamic condition is that in a homogeneous
ocean the total current consists of a pure drift cur¬
rent and of a slope current. Thus, Q = S + M,
where S and M represent the water transports in
the pure drift current and the slope current, res¬
pectively, according to eqs. (8.50) or eqs. (8.53)
and (8.62). Therefore
div S' + div M = 0 (8.111a)
With an arbitrary orientation of the xy-plane with
respect to the wind, S = + SI, where Sx
= Tylf, Sy — —Tx/f; and M = V"M% + Ml, where
Mx and Mv are given in eqs. (8.70). With the x-axis
pointing to the east and the y-axis pointing to the
north, dcfr/dx — 0 and d(f>/dy = 1/7?, where is
the geographical latitude and 7? the radius of the
earth. Thus
= n g/"1 _ 1
8x ’ By fR tan
dlvS = dk(f) ~8y{~f) =7curlT 1 fR tan
(8.111)
div M =
8MX 8MV
8x + 8y
BdiVyS+^H
fiy Sy + fty 8x 8y
(8.112)
where /3X = —(d£/dx), /3y = —(8^/dy), and curl /3
= 0.
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 213
214
It is difficult to find explicit expressions for the
derivatives of B and b since these quantities depend
on D*, that is, on the effect of friction. In the
following, the variability of D* in the x- and y-
direction will be taken into account only formally.
This, however, implies the introduction of variable
frictional effects. With
j pg 8k _ k
2co sin cp ’ 8y R tan cp
B = b — kd — B (eqs. 8.69)
it follows that
8B B 8D*. 8B B 8D* B
8x D* 8x ’ 8y D* 8y R tan cp
8b , 8d B 8D*
(8.113)
8x = kTx~ - D* 8x
8b B 8D* B tan a
8y 8y D* 8y R tan 4>
where tan a is defined by eq. (8.73). With the
derivatives for B and b as given in eqs. (8.113),
eq. (8.112) can be written
div M = B div /3
B
D*
,o a^SD* , „ ,8D*
(fix fiy) “I” (fix fiy) fly (8.114)
The divergence and vorticity of the deep current
G [eq. (8.76)] are
div G =
k/3x
pR tan cp
(8.115)
curl G = —— div J3 H-rrr~r (8.116)
P pR tan cp v '
Substitution of eqs. (8.111) and (8.114) into eq.
(8.111a) with consideration of eq. (8.116) yields
curl G =
pBf
curl t
kl
PB
+ pD*l(fi*~fil,)^ + (fi
pR tan cp {@x tan a + ~Rf)
(a 8d Q 8d\
fiy)
8y
8D*
8y .
(8.117)
Equation (8.115) shows that the deep current on a
spherical earth, flowing in the meridional direc¬
tion, is not exactly non-divergent. The divergence
increases with decreasing latitude as a result of
the divergence of meridians (or convergence toward
the poles).
Ekman’s (1923) differential equation (8.117)
describes the effects of variable wind stress, vari¬
able depth, variable friction, and variable latitude
on the deep current. With the assumption that
frictional effects are everywhere the same in the
wind-driven circulation of a whole ocean, D*
= constant, and the term containing the deriva¬
tives of D* drops out. Although this assumption
may not be true, it seems that the neglect of the
third term on the right-hand side of eq. (8.117)
would produce the least change in the dynamics of
the deep current. It must, however, be admitted
that our knowledge about regional changes of
frictional forces in the ocean is still very poor,
and the neglect of this term is also dictated by the
lack of knowledge.
With D* — constant and
Gx = ^-fiv, Gy = ~fix
r r
and tan a = b\B [according to eq. (8.73)], eq.
(8.117) can be written
curl G =
PB
-r curl t
1
+ p(G‘Sc + G d = 0
d^]_dd_8f4_dd_ _df_1
dy d dx dx d dy (8.120)
dx R tan
(8.122)
This condition is satisfied when the depth d in¬
creases toward the poles according to an equation
of the form
d = d0 sin (f> + constant (8.123)
In this case, both 8^/8x and 8^/dy are free and,
therefore, currents in all directions may occur.
Equation (8.123) states that under these conditions
the influence of the variation of the Coriolis param¬
eter (Wf) with latitude is balanced by the influ¬
ence of the variable depth (fVd). Ekman called a
depth distribution that follows eq. (8.123) the
“critical slope” of the bottom.
Ekman (1923) has demonstrated the effect of
bottom topography on currents by studying special
cases of particular interest in a homogeneous ocean.
The slope of the sea surface and the resulting cur¬
rents were considered to be caused by the wind and,
therefore, dependenton frictional forces at the sea
surface and within the water (bottom current). For
this type of current and disregarding the variation
Figure 8.21 (a) Ekman type of streamline deflec¬
tion for a flow over a submarine ridge in homogeneous
water. The upper part of the figure shows the deflec¬
tion in a horizontal plane, (b) Sverdrup type of stream¬
line deflection for a flow over a submarine ridge in
homogeneous water. The upper part of the figure
shows the deflection in a horizontal plane, (c) Mixed
type of streamline deflection for a current crossing a
submarine ridge. (All types are shown for the North¬
ern Hemisphere.) [From Neumann (I960).]
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 215
of the Coriolis parameter with latitude (planetary
vorticity effect), Ekman (1923) could show that
currents in the Northern Hemisphere will be de¬
flected to the right when passing over a bottom
where the depth decreases, and to the left where
the depth increases. In the Southern Hemisphere
the deflections are the opposite. The magnitude of
these deflections proved to be independent of the
absolute depth and affected only by the slope of
the bottom. Figure 8.21(a) shows this type of deflec¬
tion for a current passing over a submarine ridge.
The deflection is strongest over the shallowest part
of the bottom or over the deepest part in the case
of a flow over a trough. Ekman’s deflection results
in a net displacement of the streamlines, to the
right in the Northern Hemisphere and to the left
in the Southern Hemisphere.
Sverdrup (1941) pointed out that in the case of
a nonhomogeneous ocean certain modifications of
Ekman’s results must be expected. When a relative
current approaches a submarine ridge, a current
deflection as shown in Figure 8.21(b) should occur
as the result of a rearrangement of the field of mass
in the moving layer. This type of streamline deflec¬
tion is significantly different from Ekman’s type.
Contrary to Ekman’s model, where frictional forces
are decisive, it appears that in Sverdrup’s case the
effect of a varying Coriolis force is the significant
factor (Neumann, 1960). As the current approaches
the top of the ridge it will deviate more and more
to the right (Northern Hemisphere), until it reaches
a maximum displacement over the crest of the ridge.
After having crossed the crest, the streamlines turn
back to the left, and no net displacement of the
current results if the depth on both sides of the
ridge is the same. The case of a variable Coriolis
parameter including friction was considered by
Neumann (1960) (see Figure 8.21 (c)).
Ekman (1932) also extended his studies to include
non-linear field accelerations. The acceleration,
originally regarded as effectively eliminated from
the equations, was found to be important as far as
the deep current was concerned. The effects of
bottom topography and of the variation of the
Coriolis parameter on the deep current are more
or less diminished owing to accelerations. For ex¬
ample, in the case of a current flowing over
increasing depth, the revised theory (Ekman, 1932)
indicates a tendency toward contra solem rotation,
not only where the current flows in the direction
of increasing depth but also where the depth is a
maximum, and vice versa.
In Ekman’s theory of horizontal wind-driven
currents, and in eq. (8.118), frictional effects are
implicitly introduced by vertical shearing stresses
which appear in the depths of the upper (D) and
lower (D*) layers of frictional influence, or in the
quantity B = kD*!2n. The deep current appears
essentially as a frictionless current. The introduc¬
tion of frictional forces resulting from lateral shear¬
ing stress may modify Ekman’s results, especially
as far as the deep current is concerned. Lateral
shearing stresses and their frictional forces must
play an important part in ocean currents that do
not reach the bottom, as is the case in oceanic
water bodies where the density increases consider¬
ably with depth.
A general analytical solution of Ekman’s prob¬
lem for an entire ocean is still difficult to obtain,
although, with electronic computing methods,
numerical results for specific cases can be given.
However, a solution to the problem of the wind-
driven ocean circulation also requires consideration
of the density stratification in a baroclinic ocean
and the introduction of friction in the deep current.
Stratified Ocean
The total pressure field in a stratified ocean can
be considered to be composed of the relative field
of pressure due to differences in the distribution of
mass, and the slope field of pressure originating
from a slope of the sea surface. In a homogeneous
ocean the slope field is independent of depth. In a
stratified ocean it may decrease with depth and
even vanish at some height above the bottom if
the ocean is deep enough and the density stratifi¬
cation is sufficiently strong. This was explained in
Chapter 7 in connection with Figure 7.34 for
stationary or nearly stationary slope currents. If
in a stratified ocean a relative current exists and
suddenly, for some reason, a slope of the sea sur¬
face is produced in addition to the relative field
of pressure (for example, piling up of water due to
a rising wind), the slope field of pressure during
the early transient (accelerated) state of develop¬
ment of the slope current will be independent or
nearly independent of depth. However, as the slope
current gradually approaches the steady state, a
readjustment of the field of mass can compensate
in whole or in part for the pressure field produced
by the slope of the sea surface. Therefore, it is very
difficult in most cases to separate the relative field
from the slope field of pressure.
Ekman’s Relative Currents and the Elementary
Current System in a Baroclinic Ocean
The structure of relative currents including bottom
friction was first studied by Ekman (1905, 1906)
216 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
for the simple case where the density increased
uniformly with depth. Ekman assumed that the
isopycnal surfaces were planes parallel to each
other and situated such that in the relative pressure
field
dp
dx
= 0;
where d is the depth-where the isobaric surfaces
are horizontal. Further, he assumed that the abso¬
lute current velocity also vanishes at the depth
z = d and that the eddy viscosity coefficient, A, is
constant with depth. For this model, the equations
for stationary motion are
cPv
dz'2
*a,e£
dz2
Pf. — (d — z) = 0
with the boundary conditions
du _ dv
dz dz
0 for z = 0
u — v = 0 for z = d
The depth, d, represents the depth of the level
of no motion, which may coincide with the ocean
bottom or may develop at some height above the
bottom. The solution, according to Ekman, is
bd D*
2ztpf d _
Cj cosh —f, z cos a
V 2 / 2
C9 sinh - f. z sin - z
V2 7T
e-(.a/V2)z(cosJ¥L _ sin_^_\ _L Z^id z)
V V2 ■) +
V =
bd D*
2?tpf d
Cx sinh —z sin —~ z
V2 V2
D*
(8.124)
— C2 cosh - z cos z
V2 /2
+ g-(a/V2)^(cos -f- sin z
V2 /2
where
sinh 2 -^d + sin 2 —of frictional influence, D*.
[After Ekman (1905).]
xy-system to points on the curves. The end points
of the curves represent surface currents. It is seen
that in deep water (d > D*) the stationary relative
current is practically perpendicular to the pressure
gradient dp/dy. For d/D* —> oo the deflection from
the isobaric direction is zero. With decreasing d,
the relative current becomes more and more de¬
flected from the isobaric direction and flows nearly
in the direction of the pressure gradient if d 0.5D*, the currents in the lower layer between
depths d and d + D* are all directed toward the
coast. Only the currents in the upper layer have a
seaward component.
A density discontinuity surface between two
homogeneous water bodies is a crude approxima¬
tion to real density stratifications in the oceans.
Therefore, Ekman also investigated conditions
where a continuously stratified top layer spreads out
over a homogeneous deep layer. Figure 8.24 shows
the assumed vertical density distribution in the top
and bottom layers and the vertical structure of
the currents. The interpretation of the curves is the
same as in Figure 8.23. It is seen that significant
changes have occurred compared to the case of a
homogeneous top layer. The offshore transport of
water in the deeper layer is smaller. At a depth of
a little more than d - ; 0.25D* (d = 0.3D*) all the
offshore transport is carried by the currents in the
top layer and all the onshore transport by the
currents in the deep layer. If d increases, the effect
of the relative current in the top layer on the deep
water decreases, and the depth of reversal of direc¬
tion for the current component perpendicular to
the coast lies in the top layer. For d = 1.25D*,
the deep water is only slightly affected by the
motion in the top layer, and the currents are
nearly parallel to the coast. If the thickness, d, of
the stratified upper layer is large and the stratifi¬
cation strong enough, the deep water will remain
practically motionless. From these results, Ekman
drew the important conclusion that the sea surface
will adjust its slope in such a way that the horizontal
pressure gradient produced by density differences in
the upper layers of the sea gradually vanishes at some
depth beneath the strongly stratified upper layer and
increases toward the surface. This agrees with the
concepts discussed in Chapter 7 on the develop¬
ment of a layer of no motion in a stratified ocean.
Ekman’s investigations also demonstrate the im¬
portance of vertical density stratification on wind-
driven currents.
The three constituents of an elementary current
system in a non-homogeneous ocean, where a
strongly stratified upper layer lies over a less
strongly stratified or homogeneous deeper layer,
are, according to Ekman:
(a) the slope current,
(b) the relative current, and
(c) the pure drift current.
The slope current will reach the bottom only
218 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
(b)
Figure 8.24 Vertical structure of a current off a
straight coast projected on a horizontal plane as shown
in (b) where the density in the top layer increases
linearly with depth, and the bottom layer is homo¬
geneous as shown in (a). [After Ekman (1906).]
when the slope (pressure field) of the sea surface is
large, compared to the relative pressure field. If
the sea surface slope is just strong enough to com¬
pensate for the inhomogeneity of the density field
in the upper strata of the sea, the deep current is
missing and therefore also the bottom current.
The pure drift current will not differ significantly
from the drift current in a homogeneous sea if the
more or less homogeneous top layer is thick
enough, compared to the depth of the upper layer
of frictional influence.
Simple mass distributions, such as are assumed
in Ekman’s basic examples, rarely occur in nature.
However, the results obtained by Ekman nearly
sixty years ago indicated how further progress could
be achieved, and Ekman himself followed these
indications in his further studies (1928, 1929, 1931,
1932, 1939). His endeavor was directed toward
solving the problem of the three-dimensional oce¬
aniccirculation. At present, dynamic oceanography
is still far from having accomplished this task,
although the development of modern electronic
computing machines has eased some of the mathe¬
matical restrictions. Instead of analytical solutions,
numerical solutions can be given for more com¬
plicated cases. Attempts to study theoretically the
vertical velocity structure of the oceans with special
assumptions were partly successful (Hidaka, 1955,
1961; Hassan, 1958; Stommel, 1960; Charney,
1960; Veronis, 1960).
Ekman worked with models for which frictional
forces were introduced essentially from vertical
shearing stresses only. Rossby (1936) pointed out
that frictional forces resulting from lateral shearing
stresses must play an equally, if not even more,
important part in the general circulation. Studies
by Montgomery (1940) and Montgomery and
Palmen (1940) also indicated the importance of
lateral stresses in the dynamic balance of oceanic
current systems.
The importance of frictional forces other than
those resulting from vertical shearing stresses be¬
comes obvious in a stratified ocean where currents
resulting from a sea surface slope do not reach the
bottom. In Ekman’s elementary current system of
a homogeneous ocean a “bottom current” would
supply the necessary anisobaric balance of the mass
transport in the upper layer of frictional influence.
In a stratified ocean the horizontal pressure gradi¬
ent may vanish at some height above the ocean
bottom, and the necessary balance for the an¬
isobaric transport has to be provided by the relative
current. If the mass distribution balances the hydro¬
static pressure differences resulting from sea sur¬
face slopes in such a way that no bottom current
can develop, all of the anisobaric mass transport
has to be supplied by the relative current. Thus,
the relative current cannot be a non-divergent
current, although for some purposes it may be
considered as almost non-divergent.
Further development of the theory
of wind-driven ocean currents
A complete mathematical analysis of wind-driven
currents in the baroclinic oceans is difficult, for
several reasons.
In the three-dimensional oceanic circulation the
vertical velocity component has to be taken into
account, and the vertical distribution of the hori¬
zontal velocity field has to be determined.
The density stratification in the lateral and ver¬
tical directions is partly the result of an adjustment
of the field of mass to the field of currents. Difficul¬
ties arise in formulating mutual relationships be¬
tween these two fields, especially when friction is
included.
For wind-driven currents, a vertical velocity
shear can also be the result of friction, and the
variable lower boundary of the currents in a strati-
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 219
220
fied ocean is related to the field of mass as well as
to frictional effects of the fluid. The introduction
of correct frictional forces in the analysis meets
difficulties. Mathematical difficulties also arise
from the presence of nonlinear field accelerations,
which may be significant in some regions of the
flow.
Although successful consideration of all possible
effects on the oceanic circulation has not yet been
achieved, some progress has been made with certain
assumptions and simplifications, especially in the
analysis of the total horizontal mass or volume
transports by wind-driven currents. Most frequently
the assumptions are retained that the currents are
non-accelerated and that the coefficients of vertical
(Az) and horizontal (Ah) eddy viscosity are con¬
stant. With these assumptions, and by consider¬
ation of eqs. (8.27), the equations of motion for
horizontal flow become
r dp , . 8'2U . .
-fpv = -^ + A^ + A^U
a as (8‘125)
fpu— — + A:j~i + Ah\7-V
where f = 2u> sin and the operator V2 = 82/8x2
+ 82/8y2.
The total horizontal mass transport, S', between
the lower boundary, D(x,y), of the current and the
sea surface, £(x, y), is given by the components
Sx = J^pudz; Sy = J^pvdz (8.126)
Integration of eqs. (8.125) over z between the limits
D and f yields
-fSy =
8 ft , . d% 3D
~Xx) 3}-'’” dx
+ T. x (.tx)d T Rxdz
fSx = -■§-,
dD
8y J 1 8y dy
+ Ty ~ (Tv)b + Ry dz
(8.127)
In eqs. (8.127), tx and ry are the x- and y-com-
ponents of the wind stress exerted at the sea
surface; (rx)D and (jy)D represent possible tangential
stresses exerted at the lower boundary D of the
current. The vertical integrals over the horizontal
components of the frictional force are symbolically
written with the abbreviation
Rx zIaV2m
Ry Ah\/-V
(8.128)
Some investigators have introduced other forms for
internal horizontal friction than those stated in
eqs. (8.128).
If the first equation in (8.127) is differentiated
with respect to y and the second equation with
respect to x, subtraction of one from the other
yields
ASA
dy) dy dx)
(dpD dD
\ dx dy
d(ry)n ,
dx ^
dpD dD
dy dx
dir*),,
dy
\ I dTy 8tx
) dx dy
d_
dx
Rydz
dy II
(8.129)
Rx dz
For stationary upper and lower boundaries of
the current, 8Sx/8x + 8Svl8y = 0 in rectangular
coordinates, according to eq. (7.46). Also, if it is
assumed that the atmospheric pressure, />f, is con¬
stant at the sea surface, the first term on the right-
hand side of eq. (8.129) equals zero, since Vp( — 0.
In a stratified ocean where the absolute velocity
vector gradually vanishes at some distance above
the solid bottom, the bottom stress with its com¬
ponents (tx)d and (ry)n may vanish or be neglected.
With these assumptions concerning both the model
and the effects that can be neglected, eq. (8.129)
reduces to
df
y By
+ 8_
dy
(drx dry\ _ d__ A
\dy dx / dx J /
f? d j _ dpn dD
J DR*dZ~Wte
Rydz
dpi> dD
dx dy
(8.130)
The form of eq. (8.130) would correspond to
Ekman’s equation [eq. (8.118)] in a homogeneous
ocean if the frictional terms were replaced by
bottom friction and D represented the depth of
the ocean bottom.
Stockman (1946) first pointed out how the verti¬
cally integrated equations of motion can be used to
avoid some of the difficulties involved in the solu¬
tion of the problem of steady-state, wind-driven
ocean currents.
Stockman (1946) employed friction in the form
of eqs. (8.128). However, he neglected the term
Sv(8f/8y) and assumed D — constant.
Sverdrup (1947) neglected lateral friction (Rx
= 0, Ry = 0), and also assumed that the horizontal
pressure gradients due to the slope of the sea sur¬
face and density stratification compensate at some
depth D = constant. Thus, eq. (8.130) was used
by Sverdrup in the form
*s» + (j? ~ ji) =0
where ft = dfidy.
Sverdrup (1947) and Reid (1948) have applied
this equation to the horizontal transports of cur¬
rents in the eastern Pacific as maintained by the
wind stress. In addition to eq. (8.131) the continuity
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
equation [eq. (7.46)], must be satisfied. If the wind
stress is predominantly in the zonal direction,
tv = 0, and /3Sy + drx/8y = 0. Thus, in connec¬
tion with eq. (7.46) it follows from Sverdrup’s
formulation that
8SX _ d_ / 1 3tx\
dx 8y\j3 dy )
(8.132)
If internal lateral friction is neglected, eqs. (8.131)
and (8.132) can satisfy the boundary conditions
only at one meridional and two zonal boundaries.
Sverdrup (1947) introduced the meridional bound¬
ary condition that at the eastern coast the total
transport, Sx, perpendicular to the coast equals
zero.
Welander (1959) extended transport computa¬
tions on the basis of Sverdrup's equation [eq.
(8.131)] to the three oceans, introducing the actual
shape of the boundaries and wind stress data pub¬
lished by Scripps Institutionof Oceanography
(1948) and by Hidaka (1958). The computations
were carried out by numerical integration using
a relaxation technique. Since boundary conditions
along the western boundaries could not be satisfied,
no results could be obtained for the details of the
western boundary currents. The results of the com¬
putations are shown in Figure 8.25, where the
values of the transport in the western boundary
currents are only schematically indicated.
In connection with the results obtained in Figure
8.25, Welander (1959) discussed in detail the impor¬
tance of terms neglected in the Sverdrup transport,
that is, such terms as lateral friction, local time
variation, incomplete compensation at the variable
lower boundary, D, of the current, and the effects
of evaporation minus precipitation. The complete
theory, however, is very difficult to handle mathe¬
matically.
The important effect of the variation of the
Coriolis parameter with latitude on the currents in
a closed rectangular ocean was clearly demon¬
strated by Stommel (1948). He introduced, in addi¬
tion to a zonal wind stress applied at the sea
surface, internal friction in a form comparable to
the Guldberg-Mohn assumption [eq. (8.2)]. With
this, the four boundary conditions in a closed
(rectangular) ocean could be satisfied such that the
ocean boundaries are streamlines for the total
horizontal mass transport, and the transport
component perpendicular to the coasts vanishes.
The depth of the ocean was assumed to be con¬
stant. Thus, with D = constant, eq. (8.130) ex¬
presses a vorticity tendency balance of the planetary
vorticity, the curl of the wind stress, and the fric¬
tional vorticity. By means of the equation of con¬
tinuity [eq. (7.46)], a stream function, can be
introduced for the horizontal mass transport such
that
5 V
__ d'xfr
dx ’ (8.133)
Stommel applied frictional forces in the form
Rx = — pku
Ry = — pkv
where k = constant. From this, and by consider¬
ation of eqs. (8.133), the vorticity-tendency equa¬
tion [eq. (8.130)] can be written
@fa+kV2^ = curffiT (8.134)
With the assumption that ry = 0 and that a
purely zonal wind stress is given by
eq. (8.134) can be solved analytically, and adequate
boundary conditions can be applied. The result,
according to Stommel (1948), is shown in Figure
8.26. The center of the anticyclonic current gyre
is strongly displaced to the west, and a westward
intensification of ocean currents is apparent.
Goldsbrough (1935) also obtained an intensifica¬
tion of currents to the west when dealing with a
theoretical model of an ocean that covered the
whole globe, where the wind acted in closed gyres.
Horizontal frictional forces in the form of eqs.
(8.128) were introduced by Munk (1950). The basic
differential equation applied to an ocean of con¬
stant depth is obtained from eqs. (8.130) and (8.133)
in the form
^aV4^-/3^= -curf-r (8.135)
It is seen that this equation reduces to Sverdrup’s
equation [eq. (8.131)] if lateral friction is neglected,
and to Stockman’s equation if fi(chjr/dx) is ne¬
glected. It also agrees with Stommel’s equation [eq.
(8.134)] if the difference in the assumption about
friction is considered.
Munk (1950) used actual wind stress data and
could show that the zonal wind system divides the
oceanic circulation into a number of cyclonic and
anticyclonic gyres that agree qualitatively remark¬
ably well with the observed currents. The Sverdrup
type solution was closely approximated in the
central and eastern part where planetary vorticity
and curl, r have opposite signs. In the western part
of the oceans planetary vorticity and wind stress
curl have the same sign, and both must be balanced
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 221
F
ig
u
re
8
.2
5
S
v
e
rd
ru
p
tr
a
n
sp
o
rt
a
n
d
b
o
u
n
d
a
ry
c
u
rr
e
n
ts
in
th
e
o
c
e
a
n
c
o
rr
e
sp
o
n
d
in
g
t
o
t
h
e
a
n
n
u
a
l
m
e
a
n
w
in
d
st
re
ss
fi
el
d
.
T
h
e
f
ig
u
re
s
g
iv
e
th
e
t
ra
n
sp
o
rt
i
n
m
il
li
o
n
m
3
se
c~
l
in
d
if
fe
re
n
t
p
a
rt
s
o
f
th
e
b
o
u
n
d
a
ry
c
u
rr
e
n
ts
.
[F
ro
m
W
e
la
n
d
e
r
(1
9
5
9
).
]
Figure 8.26 Streamlines of the wind-driven water
transport in a rectangular ocean of constant depth
according to Stommel (1948). Note the extremely
strong westward concentration of ocean currents.
by the frictional vorticity tendency. This again
leads to a westward displacement of circulation
gyres and strongly concentrated western boundary
currents.
Hidaka (1950, a,b, c), also dealing with an ocean
of constant depth and making use of eq. (8.135),
obtained remarkable results that agree well with
the average circulation in the Pacific. He applied
a different wind system and larger coefficients, Ah,
of lateral friction. He found that the westward
intensification of the streamlines for the horizontal
mass transport weakened with increased lateral
friction.
Application of the theory by Munk and Carrier
(1950) to a triangular ocean shows the remarkable
progress that has been achieved since Ekman’s
classical theory. Figure 8.27 shows the theoretical
solution for the horizontal mass transport in a
triangular ocean in the Northern Hemisphere that
can be compared with the North Pacific.
For the North Atlantic, Hansen (1951) dealt with
the problem of the horizontal circulation as an
eigenvalue problem. He also computed the sea sur¬
face topography for the equatorial region for the
mean wind field in August. Qualitatively, his results
agree well with actual observations.
Although these results give a fairly good quali¬
tative picture of the wind-driven circulation in the
oceans, the quantitative agreement with observa¬
tion is not always satisfactory. However, when
comparing theoretically computed horizontal mass
transports with observations, the critic is inclined
to base his judgment on the pattern of the sea sur¬
face currents. The knowledge of vertically inte¬
grated, wind-driven, horizontal water transports
in most parts of the oceans is still too inadequate
to permit a conclusive criticism of theoretical
results.
Our present knowledge of the circulation in the
upper layers of the oceans seems to indicate that
the currents in the Southern Hemisphere—for ex¬
ample, the Brazil Current and the East Australian
Current—are not as strongly intensified toward the
western boundaries. Also, some intensification
toward the coast is observed along the eastern
boundaries—in the California Current, Peru Cur¬
rent, Canary Current, and Benguela Current, for
example. Although the variation of the Coriolis
parameter with latitude is one important factor in
the dynamics of ocean currents, and although it is
responsible for the westward intensification of
ocean currents, it is not the only factor that can
account for the intensification of currents in narrow
swift bands. It appears that other factors depending
on the vertical structure of the oceans, such as the
three-dimensional momentum exchange, the vari¬
able depth of currents, and the convergence of
y
Figure 8.27 Streamlines of computed water mass transport in a triangular
ocean. The transport between two adjacent streamlines is 6 million tons per second
in the direction of the arrows. [From Munk and Carrier (1950).]
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 223
meridians on a spherical earth, play an equally
important part (Neumann, 1952, 1955).
The Effect of Lateral Eddy Momentum Exchange
The effect of turbulent momentum exchange on
currents is two-fold. In the first place, eddy vis¬
cosity stresses and friction tend to slow down the
motion. In the second place, the turbulentFigure 8.2 show that
cot 7 = tan a =
2a> sin 4>
r cos ft + tan/3 (8.8)
which reduces to eq. (8.3) for ft = 0. If the angle
ft were known along with a, the effective internal
friction coefficient, r, could easily be determined.
Defant (1929) estimated the value of r to be
between 10~6 and 10~7 [sec-1] for ocean currents,
and Neumann (1954) found an average ofra=3 X
10“6 for the upper thousand meters of the oceanic
circulation. The order of magnitude, r 10~6,
corresponds to a deflection angle 7 = 90° — a
of about 2° in middle latitudes.
Although the Guldberg-Mohn assumption may
serve as an approximation for introducing an
average friction in some cases of horizontally
moving layers, it is unsuitable for a more detailed
analysis of frictionally driven currents. For example,
the Guldberg-Mohn equations fail to explain the
observed shift in current direction with height in
the atmosphere or with depth in the ocean, respec¬
tively.
The Decay of a Current Under the Effect of Friction
A simple case of decay of current velocity by fric¬
tion can easily be treated with the Guldberg-Mohn
assumption (Defant, 1929).
The equations of motion in the accelerated (or
decelerated) case are
du r dp
ru
dv
dt
r dp
~fu ~ady~ ™
(8.9)
where a = 1/p. If the first equation in (8.9) is multi¬
plied by u and the second by v, and the equations
are added, it follows that
du
dt
dv
'dt = +Tyv)-r(“'+',motion
influences the flow pattern, and in turn, the stratifi¬
cation by kinematic effects.
The importance of frictional forces due to lateral
shearing stresses was emphasized by Rossby (1936).
Although the geostrophic equilibrium condition
[eq. (7.75)] may not be essentially changed, the
introduction of lateral turbulent motion imposes
certain restrictions on the transverse velocity profile
of a current.
There is evidence that lateral mixing and ex¬
change of momentum prefer isentropic surfaces.
Isentropic surfaces are, with sufficient accuracy,
surfaces of constant at. Although the intensity of
vertical mixing decreases with increasing stability,
it seems that lateral mixing along isentropic sur¬
faces increases with increasing stability. For the
oceans, this fact was pointed out by Parr (1932),
and it appears that either vertical or lateral mixing
dominates. In the wind-stirred surface layers the
mixing process is dominated by vertical turbulent
fluctuations, whereas in stably stratified subsurface
layers vertical exchange may become insignificant
compared to lateral exchange.
Consider a turbulent horizontal current and
orient the xy-plane parallel to isentropic surfaces
(oy surfaces). Although isentropic surfaces are
slightly curved, they may be considered approxi¬
mately plane in the vicinity of the zero point of the
coordinate system.
Superimposed on the average flow with the
velocity components U and V are turbulent fluctu¬
ations u' and v' in the x- and ^-directions, respec-
tively.t With the neglect of vertical velocities, it
follows from eqs. (8.13) that u■ — U + u' and
v = V + v', and the equations of motion are
d(U+ u')
dt
d(V + vf)
dt
= f(V
r\ 1 dp
V )--7T
p dx
-nu+u')-^fy
(8.136)
where/= 2co sin cf>. It is also possible that turbulent
flsentropic surfaces are slightly inclined against level sur¬
faces, and there is a very small component of gravity acting
in this plane. A term containing g should be added to eq.
(8.136). It is omitted because of its insignificance to the
problem.
velocity fluctuations are associated with turbulent
pressure fluctuations, p', and so p = P + p'. How¬
ever, in the following it will be assumed that the
superimposed turbulent motion is not reflected in
turbulent pressure fluctuations, and that p =: P.
Also, possible density fluctuations, p', are con¬
sidered negligible.
With these assumptions, eqs. (8.136) become
dU rrdU vdU djf_
dt + dx + dy + dt
U
di/
dx
V
du'
dy
t dli . r dU 1 dp . rjs | r r
u 3-hi’ 3—=-+ fV + fv
dx dy pdx
,dU ,dU
— u -=-V -5-
dx dy
8X+u8^-
dt ' u dx
v
dy
dv' . jj dv’
dt + dx
V
dv'
dy
/ dv | f dv _ 1 dp rjT r T
U 3-hi) -5— =--f- — fU — fu
dx dy p dy J
,dV tdV
U s-V -5—
dx dy
(8.137)
With stationary conditions for the basic (average)
current, 8U/dt — dV/dt = 0, and the assumption
that
U dJl _i_ y dU =_L dp , ry
dx ^ dy p dx^J
U
dV
dx
ydX — LdP _ fy
dy p dy J
(8.138)
it follows from eqs. (8.137) that
du' _ du'
dt dt
(U + W) ^ + (V+v')^
f , , dU , dU = jv — M -5-V -5—
dx dy
dv'_dv'
dt dt
(U + ur) lf + (V + v')8/-
8 x dy
(8.139)
,8V ,dV = —JU — u -5-V
dx dy
If the first equation in (8.139) is multiplied by
v' and the second equation by u! the sum is
, du' , dv'
dt dt
f(v'> - u'*)
, ,(dU ,dV\ ,2dU
" ” fe + 8?) - “ W~“
,SV
dx
(8.140)
For w = 0 (in a first approximation), and incom¬
pressible flow
dU
dx
and it follows from eq. (8.140) that
£ («V) =f(v'* - «'2) - v'^ - u'*^ (8.141)
From the work of Prandtl, it can be assumed that
the turbulent fluctuations caused by initial pushes
in the x- and ^-directions preserve their momentum
224 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
over a distance, lx and /„, respectively, which they
traverse during the time interval, 8t. Such distances
represent a lateral “mixing length.” Thus, with
u' = lx/8t and v' = ly/8t, it follows that
u’ V
T = T~ = constant = (Sr)-1 (8.142a)
lx ly
and
l^ly = v'lx (8.142b)
Substitution of eq. (8.142b) into eq. (8.141) yields
A
dt Ay, a certain lateral shear 8V/dx ^ 0 develops.
The maximum lateral shear, however, will be found
only in the special case where Ay — 0 and Ax 0.
The condition that Av = 0 implies that no turbulent
fluctuations occur in the direction of the average
current. This is the case considered by Rossby
(1936) in which
8V
8x
— 2co sin (p (8.148)
This result was criticized by Ekman (1939). As
Ekman argued, results as obtained in eq. (8.148)
would cause irregular fluctuations to follow curved
paths which represent parts of the circle of inertia.
This should lead to the development of strong
lateral shearing. Since the effect of the earth’s
rotation on horizontal turbulent fluctuations is
independent of the dimensions of the “mixing
length” it should apply in the same way to molec¬
ular motion. Thus, according to Ekman, “the
curved paths taken by the water masses would lead
to the development of stresses that would tend to
set the entire body of water in rotation” (Sverdrup,
et a/., 1946, p. 478). Evidently, this contradicts
experience. However, eq. (8.148) holds only for
“monotropic” turbulence, and Ekman’s criticism
applies for isotropic turbulence. With molecular
motion, one can assume that on the average
Ax = Ay and, therefore, from eq. (8.147), dV/dx
= 0. It seems that Ekman’s criticism was the
result of a misunderstanding of Rossby (1936),
who assumed that, at least, the turbulent fluctua¬
tions in the cross-stream direction are many times
stronger than the turbulent fluctuations in the
average flow direction.
Therefore, an effect of lateral turbulent fluctu¬
ations on the horizontal velocity profile exists, notexactly as given by Rossby in eq. (8.148), but
rather as given in eqs. (8.147). Priebsch (1943) has
shown by a different analysis that for Ay/Ax = 1,
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 225
Figure 8.28 (a) Density section across the Gulf Stream based on Atlantis Sta- (a)
tions 2485-2492. The arrows indicate probable lateral and vertical motions as
deduced from the phosphate section (phosphate phosphorus, mg P per m3) shown
in (b). [From Neumann (1952).]
the lateral shear 8V/dx must vanish, and Raethjen
(1942) has applied eq. (8.147) in the form 8V/dx
= —r)f, where ?/ was called the “monotropy co¬
efficient.” In eq. (8.147), Raethjen’s monotropy co¬
efficient is related to the ratio Ay/Ax. If the average
flow is oriented in the x-direction, the second
equation in (8.146) applies with similar results.
These results show that if no forces act against
lateral momentum exchange, the basic current
tends to create a lateral velocity profile according
to eq. (8.147). If this velocity profile has developed,
lateral momentum exchange and friction are at a
minimum or zero, and quasi-stationary conditions,
which imply an “equilibrium of the lateral momen¬
tum exchange,” are obtained for the current. This,
of course, does not prevent the field of mass from
adjusting to the current field approximating geo-
strophic conditions with a stationary flow.
Figure 8.28(a) shows a density section across the
Gulf Stream between about 50°N, 41 °W and 40°N,
41 W. From the density distribution it is seen that
the Gulf Stream in this area was split up into two
main branches at the time of these observations.
The northern branch has its axis in the vicinity of
Atlantis Sta. 2491; the southern branch, between
Sta. 2486 and 2485.
A phosphate section, showing phosphate phos¬
phorus (in mg P per m3) is presented in Figure
8.28(b). The density distribution and the phosphate
distribution show a remarkable similarity. The
phosphate maximum, normally observed at greater
depths (around 1000 meters), is found to follow
226 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
(b)
50'08’N
the inclined isopycnal surfaces in the region of
maximum current velocity or to be slightly dis¬
placed to the left-hand side when one is looking
in the current direction. This indicates “upwelling”
of water with a high phosphate content caused by
lateral water movements that are superimposed on
the average flow of the Gulf Stream branches per¬
pendicular to the section. This “cross-circulation”
in the Gulf Stream branches is schematically indi¬
cated by arrows in Figure 8.28(a). It is possible
that the cross-circulation and its fluctuations, which
may be caused by wind fluctuations, act like
“turbulent” motions superimposed on the average
current. Thus, a lateral shear according to eq.
(8.147) with Avthe current velocity
decrease rapidly with increasing distance from the
coast if the current flows in zonal x-direction over
increasing depth.
Next assume a meridional coast extending with¬
out bounds in the y-direction. Again, the coastal
current with transport Sy will be produced by a
uniform wind (r =_constant). Then, for homo¬
geneous water, eq. (8.153) reduces to
**•+- f “\8x 8y 8y 8x)
(8.157)
If D is constant and the transport perpendicular to
the coast, Sx, vanishes
dSy __ /3 „
dx r (8.158)
which leads to a westward intensification of the
transport, Sy, in the western boundary currents as
a result of the planetary vorticity effect.
In the case where D is a function of y only, and
gp — 7f Sy with Sx = 0
eq. (8.157) reduces to
+ (8.159)
The planetary vorticity effect in eq. (8.159) is
cancelled by the topographic effect for the special
case where /3/f= (1 / D)(8D/8y), or if the lower
boundary of the current increases in proportion
to the sine of geographical latitude [eq. (8.123)].
In this case, 8Sy/8x = 0.
If D is a function of x only, it follows from eq.
(8.157) with Sx = 0 that
f3s’ + r-si = gPs,-si (8'160)
The solution of this equation depends on the slope
d^dy. With 8^/8y = 0, the planetary vorticity effect
causes a westward intensification as in eq. (8.158),
independent of 8D/8x.
In western boundary currents such as the Gulf
Stream, the positive transport, Sy, however, does
not increase continuously toward the coast. Near
coasts, the current velocity and also the transport
approach zero and increase toward a maximum at
some distance offshore. From this maximum, both
current velocity and transport decrease more or less
rapidly in the positive x-direction. Thus, in the
nearshore (cyclonic shear) regions, 8Sy/8x > 0 and
the term on the right-hand side of eq. (8.160) must
have a finite value. If D increases in the positive
x-direction, 8D/8x 0. If D decreases in the
offshore direction, 8D/8x > 0 and 8^/8y must be
positive. In the offshore anticyclonic shear region
where 8Sy/8x is the colatitude and R is the
radius of the earth.
With dp/dt = 0, R + z ^ R, and 2w/R 0, eq.
(8.161), after integration over the depth z between
the sea surface, £(x,y), and the variable lower
boundary of the current, D(x, y), yields
~RCin6 (8-162)
The term containing ctn 6 = tan is in middle
latitude of the same order of magnitude as the
term df/dcf) or the variation of the Coriolis param¬
eter with latitude, and should be included (Ek-
man, 1923; Neumann, 1955).
From a consideration of the vertically integrated
equation of continuity [eq. (8.161)] in spherical
coordinates, Neumann and Ostapolf (1957) [see
also Neumann (1958)], applied eq. (8.129) with a
variable lower boundary, D, to the computation
of the total horizontal mass transport in the North
Atlantic. The lower boundary was essentially De-
fant’s reference level (Figure 7.39). These computa¬
tions were later extended to the North and South
Atlantic (Garner, Neumann, and Pierson, 1962).
The wind stress was computed for the average wind
field of the month of February. Coastal boundaries
were approximated by a series of straight lines
joining a grid system of two by two degrees of
longitude and latitude, nearest to the edge of the
continental shelves of bordering land masses. An
idealized “Caribbean Island” with “floating bound¬
ary conditions,” which best defines the land and
continental shelf areas in this region, was chosen.
The results of the numerical computations are given
in Figure 8.30.
A total mass transport in the Gulf Stream of
about 40 million tons per second was derived with
a transport of about 25 million tons per second
passing through the Straits of Florida. This may
be compared to 48 million tons sec-1 in the Gulf
Stream, as computed by Wiist (1936) on the basis
of the observed mass distribution. Streamlines
representing the Benguela Current transport tend
to spread away from the African coast leaving an
area of weak circulation between the equator and
about 15°S off the coast of Central Africa. In the
Gulf of Guinea an Equatorial Countercurrent is
indicated. For more details concerning boundary
conditions that may partly be responsible for the
wavelike flow pattern in higher latitudes of the
South Atlantic Ocean, see Garner (1962) and
Garner, Neumann, and Pierson (1962).
Thermohaline circulations
Differences in the heating and cooling of water at
the sea surface as well as salinity changes due to
evaporation, precipitation, ice formation, and melt¬
ing cause density differences that may produce
horizontal pressure gradients and currents.
As was shown experimentally by Sandstrom
(1908) and theoretically by Bjerknes (1916), con¬
ditions in the ocean are not very favorable for
producing strong thermohaline circulations. For an
effective thermohaline “engine,” it is necessary that
expansion (decrease of mass per unit volume) take
place at higher pressure and contraction at lower
pressure. In contrast to the atmosphere, where
heating and expansionoccur at high pressure (the
earth's surface) the thermal engine in the oceans is
both heated and cooled at the surface, that is, at
lowest sea pressure.
One would expect that heating at the equator
and cooling near the poles would produce strong
meridional density differences that lead to an
“overturning” of water masses from top to bottom
(Lenz, 1847), but according to Sandstrom and
Bjerknes this circulation would remain weak unless
the heating effect near the equator could extend
into deeper layers. This, however, is not the case
in the oceans because absorption of the sun’s
230 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
Figure 8.30 Streamlines of
the vertically integrated hori¬
zontal volume transport of the
wind-driven circulation in the
Atlantic Ocean corresponding
to the mean surface wind field
in February. Flow is parallel
to the streamlines in the direc¬
tion of the arrow heads, and
the volume of the flow be¬
tween adjacent streamlines in
millions of cubic meters per
second is given by the differ¬
ence of the indicated values.
[From Garner, Neumann, and
Pierson (1961).]
radiation and heating take place in a relatively
shallow surface layer. Although the cooler water
near the poles in fall and winter may sink and fill
the deep sea, the heat source still remains at low
pressure.
Sandstrom’s experiments have shown that neither
a heat source nor a cold source alone can produce
effective deep-reaching thermal circulations. This is
illustrated in Figure 8.31 where heat and cold
sources are nearly at the same level. The stationary
circulation occupies only a thin layer of “overturn¬
ing” water whereas the top layer accumulates the
warm water and the bottom layer accumulates, the
cold, both remaining essentially at rest. Although
Jeffreys (1925) has rightfully questioned the gener¬
ality of Sandstrom’s experiments and conclusions,
the fact remains that thermally produced circula¬
tions develop more effectively when the heat source
is deep in the oceans and the cold source is high.
Bjerknes (1936) has reconsidered the problem and
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 231
Figure 8.31 From Sandstrom’s (1908) experi¬
ments: Source of heating and cooling in a water tank
at nearly the same level. In the layer A-B, the warm
source is a little lower (at higher pressure) than the
cold source, and a stationary circulation develops in
a relatively thin layer, whereas the (warm) top and the
(cold) bottom layers remain essentially motionless.
The greater the vertical difference between the two
sources with “warm'’ below and “cold” above, the
more extensive becomes the thermal circulation.
analyzed controversial questions in great detail.
The fact stated above remains true.
In addition to density differences caused by dif¬
ferential heating, evaporation and precipitation
tend to change the salinity and density of surface
water. Increasing salinity acts like a cold source,
decreasing salinity like a heat source. The resulting
“haline” circulation combines with and is superim¬
posed on the “thermal” circulation. As was shown
by Defant (1929), average temperature and salinity
effects counteract each other in higher latitudes and
reinforce each other in lower latitudes, both acting
from changes at the sea surface.
The combined thermohaline circulation for aver¬
age conditions in the oceans is schematically illus¬
trated in Figure 8.32. In latitudes between about
25 and 50° thermal and haline circulations are
opposed. In lower latitudes, approximately be¬
tween the equator and 25° latitude, thermal and
haline circulations act in the same way and support
each other to produce a meridional overturning of
water masses. It is, however, to be expected that
this thermohaline circulation does not extend into
deeper layers of the ocean. A verification of this
part of the oceanic circulation seems to be indi¬
cated by high salinity intrusions from mid-latitudes
into equatorial regions, although they are sup¬
ported by the average wind-driven circulation where
ascending motions occur near the equator and des¬
cending motions occur in mid-latitudes (the sub¬
tropical convergences). This fact will be discussed
in more detail in Chapter 14 with reference to the
oceanic circulation and stratification in equatorial
and subtropical waters.
It may appear that thermohaline circulations in
the ocean are of minor importance. Flowever, they
are undoubtedly significant in the deep sea where
the wind-driven circulation gradually vanishes with
increasing depth. Haline circulations are most
significant for the deep sea stratification, especially
in the Atlantic Ocean, where high salinity water is
carried from the Mediterranean Sea into deeper
layers at about 800 to 1000 meters. In the Indian
Ocean, an outflow of high salinity water from the
Red Sea indicates similar but weaker effects. It
is remarkable that the Pacific, the ocean without
such intrusions of high salinity water, reveals a
different structure in the deep sea than the Atlantic
or Indian Oceans.
In a theoretical study, Goldsbrough (1933) dis¬
cussed steady-state oceanic circulations produced
by predominating precipitation in one hemisphere
and predominating evaporation in the opposite,
hemisphere. Although the assumptions about the
distribution of precipitation and evaporation are
very restrictive and the results purely hypothetical,
they served Stommel (1957) as a basis for a more
realistic discussion of thermohaline deep sea circu¬
lations interrelated and compatible with wind-
driven circulation in the upper strata of the oceans.
Thermohaline convection processes as shown in
the schematic Figure 8.33(a) produce a sinking of
water in certain subarctic regions and a corre-
°N 75 I
Thermol
holme
50
_i_
Cooling Q 3
Solinity
decrease
(
P>E ^ ■*-
Latitude
25_Q°Eq-_25_50_75 °S
rz tz r r c c00i,ng
Salinity Salinity Solinity Salinity
increase decrease increase decrease
S 4 V \ — /
~ PE ^ ~ ■*''PE
Figure 8.32 Representation of average sources, and sinks, for a thermohaline
circulation in the ocean. For latitudes poleward of 25°, the effect of salinity changes
on density counteract the effects of heating and cooling. An efficient thermohaline
circulation seems to be restricted to the upper layers in tropical and subtropical
regions.
232 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
Figure 8.33 Interpretation of the circulation of the
Atlantic Ocean according to Stommel (1957). A
simple thermohaline mode of circulation is shown in
(a) with a flow across a level surface (L) at mid-depth,
and a simple wind-driven mode of circulation in the
layer above L is shown in (b). Superposition of both
modes represents the circulation pattern in (c).
sponding rise in the subantarctic latitudes. Dynamic
reasoning and continuity requirements suggest that
the transport of water at great depths between the
two hemispheres is also concentrated in a narrow
western boundary current. Superimposed on this
thermohaline component of the general circulation
are the wind-driven currents as shown in Figure
8.33(b) for a simple zonal wind field symmetrical to
the equator. The wind-driven circulation, with the
exception of some boundary currents flowing over
the continental slope, does not always reach the
ocean bottom, but is confined essentially to an
upper layer of depth L, which is indicated in
Figure 8.33 by a plane dividing the ocean into an
upper and lower part. Superposition of both
thermohaline and wind-driven circulations results
in a circulation system as shown in Figure 8.33(c).
It is seen that the general circulationin the South¬
ern Hemisphere is distinctly different from that in
the Northern Hemisphere. If the model is applied
to the Atlantic this means that the Brazil Current
as a western boundary current may appear weaker
than its counterpart in the Northern Hemisphere,
the Gulf Stream. The thermohaline model of deep
circulation also emphasizes strongly the impor¬
tance of the circumpolar circulation in the Antarctic
Ocean, where it should be remembered that in high
latitudes the wind-driven circulation may reach the
ocean bottom.
Stommel’s results agree qualitatively with our
present knowledge of the spreading and circulation
of deep sea water masses, which will be discussed
in more detail in Chapter 14. The sinking of water
in the Weddel Sea seems to present an additional
source for thermohaline circulations and for the
appearance of a “bottom boundary current” in the
South Atlantic. Modern experiments by Stommel,
Arons, and Faller (1958) have supplemented and
supported these theoretical conclusions. The appli¬
cation of experiments conducted in rotating basins
to oceanic phenomena is an important modern tool
for the study of the oceans. The reader is referred
to the excellent summary of oceanographic labo¬
ratory models by von Arx (1962).
Another possibility for the formation of ocean
currents may be sought in the fact that in some
locally limited oceanic regions water is added by
precipitation and river run-off, whereas in other
regions evaporation exceeds precipitation and water
is lost at the surface. Ekman (1926) investigated
this problem in great detail and arrived at the con¬
clusion that the resulting velocities of such “evap¬
oration currents” in the open oceans would not
exceed 1 or 2 cm/sec. However, in straits that con¬
nect bays or adjacent seas with each other or with
the open ocean, convection currents of this type,
with significantly higher velocities, may result.
An example is the water exchange between the
Mediterranean Sea and the Atlantic Ocean.
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 233at the r-components) always gives the direc¬
tion of the stresses by the first subscript, whereas
the second subscript indicates the plane in which
the stress acts by showing its normal or perpendi¬
cular direction to the plane. Thus, txz means a
stress component acting in the x-direction on the
xy-plane (with the z-axis normal to it).
In Figure 8.3 consider, for example, the moment
of forces around the y-axis. There are the two
stresses, rxz and tzx, and their moments are
Fxz = — rxzAx’Ay?Az
and
Fzx
Since the resultant of these moments must disap¬
pear it follows that ^AxAyAz(rzx — txz) = 0 and,
therefore, rzx = txz. The same analysis can be
applied for other corresponding stress components.
z
Figure 8.3 Shearing stresses acting on three sides
of a cube in an x, y, z coordinate system.
If the moments did not disappear an angular ac¬
celeration would result, which would lead to infinite
velocities. The angular velocity of fluid particles
must, however, remain finite.
The Coriolis terms can be added to the hydro-
dynamic eqs. (8.20) and (8.22) for the mean velocity
components, since Coriolis forces would not con¬
tain the effect of turbulent fluctuations.)
Turbulent shearing stresses were introduced into
hydrodynamics by Reynolds (1894), and these
stresses are often called “Reynolds stresses.” Since
they contain very small fluctuations around the
average flow their numerical values are not easily
determined. There is, however, a possibility of ex¬
pressing the stresses by macroscopic quantities,
although their determination or observation in¬
volves other kinds of difficulties. Therefore, the
introduction of numerical values of turbulent “eddy
stresses” and their derivatives, as they appear in
the hydrodynamic eqs. (8.20) and (8.22), still pre¬
sent a problem in dynamic oceanography.
By analogy to the mean free path in molecular
motion, Prandtl (1925) has introduced the “mixing
length” concept for turbulent motion. Although its
physical meaning is not as precise as the definition
of the mean free path, the concept of the mixing
length, /, has provided the means for a successful
hypothetical approach to a definition of “eddy
viscosity stresses” and “eddy viscosity coefficients.”
After Reynolds’ first important step, the theory of
(■Certain effects of Coriolis forces on turbulent current
fluctuations will be considered at the end of this chapter
in the section “The Effect of Lateral Eddy Momentum
Exchange” on ocean currents.
188 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
turbulent fluctuations and their effect on the dy¬
namics of fluids and gases has been further de¬
veloped, especially for practical application, no¬
tably by Richardson (1926), v. Karman (1930),
Taylor (1931), and Prandtl (1925, 1942).
Following Prandtl’s hypothesis, consider for
simplicity only the average flow, U(z), in the direc¬
tion of the x-axis. Superimposed on the average
flow are turbulent fluctuations, u!, v', w', such that
u = U + u', v = v’ w = w'
For this simplified flow, the eddy shearing stresses
are given by eqs. (8.21). With turbulent fluctuations,
a particle leaves its original position x, y, z with
an average velocity U(x, y, z) and arrives, after
traveling a given distance l(x,y,z), at the place
x + lx, y + ly, z + 4, where lx, ly, lz are the com¬
ponents of the “mixing length” in the x-, y-, and
z-directions, respectively. If the gradients of the
average velocity in the three coordinate directions
are dU/dx, 8U/8y, and 8U/8z, the particle at the
end of its displacement comes into surroundings
where the velocity U(x + lx, y + lv, z + lz) =
U(x,y,z) + lx(8U/8x) + ly(8U/8y) + lz(8U/8z),
approximately. The velocity difference between
the particle and the fluid surrounding it in its
new position is therefore
U(x,y, z) - U(x + lx, y + ly, z + /.)
_ / dJl _ i dJl_, 8U (8.23)
~~ x dx v dy z 8z
Prandtl has shown that the magnitude of the
terms on the right-hand side of eq. (8.23) is approxi¬
mately the same as the magnitude of the turbulent
velocity components, that is
/ d_U
v dy' U(y) (8.24)
_/ 3t/
z 8z ' «i*)
The index in parentheses shows in which manner
the turbulent u' component was caused, that is,
by original pushes in either the x-, y-, or z-direction.
From eqs. (8.24) the stress components, eqs. (8.21),
can now be written
- 7~i—K _ - 7—13.
The “Law of Parallel Fields” and
Its Disturbance by Frictional Effects
For non-accelerated, frictionless ocean currents the
flow must always be parallel, not only to the
isobars but also to the isopycnals. If this condition
were not fulfilled the distribution of mass would
be altered by the fluid motion. It also follows that
the isobars and isopycnals at one level must be
parallel to those at other levels if the density
stratification is continuous and if the above-men¬
tioned assumptions hold. This rule is known as the
law of parallel solenoids or the law of parallel fields.
It was first established by Helland-Hansen and
Ekman (Ekman, 1923). This law indicates that the
total current field and the field of mass are mutually
adjusted to each other, following the geostrophic
balance of forces exactly.
The study of large-scale conditions in the ocean
has shown that over large areas the isopycnals at
different levels are indeed nearly parallel to each
other and parallel to the “average” large-scale cir¬
culation. However, in many cases, and especially
when the details of the flow pattern and the mass
distribution are examined, deviations from the law
of parallel fields are observed. These deviations are
mainly due to the fact that the currents are neither
stationary (non-accelerated) nor frictionless. If the
assumption is made that the flow can be considered
as (essentially) non-accelerated and “quasi-station-
ary,” the disturbing effects of the frictional influ¬
ences are often obvious, especially in surface layers
that are under the direct influence of the driving
forces of the wind. Essentially, these pure, wind-
driven surface currents are produced by frictional
coupling between the moving air (wind) and the sea
surface and between layers within the sea itself.
Thus, friction must play an important role in the
generation of these currents and in the mutual
adjustment between the field of mass and the field
of currents.
In a general, although idealized, way the effect
of friction and the deviation from the law of parallel
solenoids may be examined for horizontal currents
by assuming stationary conditions and neglecting
vertical motions (w = 0) (Defant, 1931). Stationary
conditions also apply to the field of mass; that is,
the local field of mass is not altered even with cur¬
rents crossing the isopycnals (dp/dt = 0).
In Figure 8.4, the horizontal distribution of
isopycnals (p = constant) and of streamlines (fir
y
Figure 8.4 In a horizontal current field (x, y plane),
if represents streamlines and p, isopvcnal lines. Both
lines intersect, and form the angle y of intersection,
it the fluid has friction and diffusion is present.
= constant) is shown in the vy-plane. The gradients
of p and fir are indicated by dp/dm and dfir/dn,
where m and n are the directions perpendicular to
the isopycnals and streamlines, respectively.
The system of horizontal streamlines follows the
equation fir(x, y) = constant, and the system of
horizontal isopycnals follows the equation p(x, y)
= constant; thus
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
dp=d£dx+%dy=o
Since du/dx + dv/dy = 0, the velocity components
can be expressed by the stream function
u = dty/dy
v = — d-yjr/dx
(8.29)
The angles a and /3 in Figure 8.4, which represent
the inclination of the streamlines and isopycnals
against the x-axis, respectively, are given by
The “crossing angle”
isopycnals is 7, and
y_ _ __ d^/dx
u d^Jr/dy
dp/dx
dp/dy
(8.30)
between streamlines and
tan 7 tan (a — ft)
tan a — tan /3
1 + tan a tan j3 (8.31)
Substitution of eqs. (8.30) into eq. (8.31) yields
tan 7 =
dty jd^r dp jdp
dxl 8y 8x/ 8y
d'f' dp d^r dp
dx dy dy dx
d'f'dp d'tydp
dy dy dx dx
(8.32)
According to eqs. (8.29), the angle 7 between the
lines p = constant and = constant, that is, the
“deviation angle” from the law of parallel solenoids
becomes
tan 7
dp dp
dy dx
8-P _JP
dy dx
(8.33)
The equations of non-accelerated horizontal mo¬
tion, including friction, are
where
R,
| -fpv-R,
**-UA‘ I) dy
= ±(
dx\
dy)
A
Aidx
JL(a
dzX Zdz)
8v\
' dz) hiA
(8.34)
(8.34a)
Differentiation of the first equation in (8.34) with
respect to y and of the second equation with respect
to x, with/ = constant, and subtraction eliminates
the pressure and yields, for a non-divergent hori¬
zontal velocity field
V^P + U^P = 1(A R
dy + U dx f \dx Ry dy R*
(8.35)
Substitution of eq. (8.35) into eq. (8.33) shows
that the angle 7 depends on friction.
tan 7
1(±R _ 2 „
/ vax dy
dp dp
11 a — V f- dy dx
(8.36)
It is seen from eq. (8.36) that in the case of no
friction tan 7 = 0, and parallel streamlines and
isopycnals are preserved. The denominator is
unequal to zero, since it represents the scalar prod¬
uct (df'/dy)(8p/dy) + (d-f/8x)(8p/dx), which has a
maximum value for 7 = 0. When friction is pres¬
ent the deviation angle, 7, between streamlines and
isopycnals is unequal to zero and increases with
increasing friction.
The result of these considerations is that friction
destroys the law of parallel fields. The deviation
between streamlines and isopycnals can serve in
practice to determine the effective friction in layers
where the density distribution and the horizontal
current field are known from observations.
If friction, resulting only from vertical shearing
stress, is introduced and the eddy viscosity coef¬
ficients are considered to be constant, eq. (8.36)
becomes
tan 7 = -7?
r d, 2d2v\ d ld2u\~\
L dx' \dz2) dy \dz'2) J
dy dx
from eqs. (8.34a). Thus
tan 7 = —
df
dz2
d2i]r
. dx2
dfff
dy'2.
/ dp dp
dy
— v
dx
(8.37)
where is the stream function.
For a potential flow the expression in brackets
is always zero, and, therefore, in this particular
case 7 should also be equal to zero. Hence, irrota-
tional currents or potential flow in the ocean
including friction cannot be assumed.
Eddy diffusion, which applies to the density field
in the same way that friction applies to the cur¬
rents, also destroys the law of parallel fields. This
will be shown later in connection with eddy dif¬
fusion and the mixing of water masses.
Wind-driven currents in a homogeneous ocean
While studying the observations of wind and ice
drift taken during the Fram expedition (Norwegian
North Polar Expedition 1893-96), Nansen (1902)
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 191
1 92
found that the drift of ice with respect to the wind
did not follow the wind direction, but deviated from
it by 20° through 40° to the right. He explained the
deviation as a consequence of the earth’s rotation
and further concluded that the water layers beneath
the surface must deviate even more from the wind
direction. Each layer of water is put into motion
by the layer immediately above, which sweeps over
it as the wind does at the water surface. These
results and Nansen’s hypothesis were in sharp
contrast to Zoppritz’ (1878) theory of drift currents,
which did not consider the effect of the earth’s
rotation.
On Nansen's suggestion, Ekman (1902) investi¬
gated the problem mathematically. His results con¬
firmed Nansen’s qualitative hypothesis and laid
the foundation for one of the most remarkable
theoretical developments in dynamic oceanography.
The first model of Ekman’s analysis (1905) was a
rather simple one; however, it was the forerunner
of a series of basic contributions to the problem of
wind-generated currents in the ocean. The results
also were almost immediately applied in dynamic
meteorology.
Pure Drift Currents in a Homogeneous Ocean
Pure drift currents are produced by the drag of the
wind passing over homogeneous water. Horizontal
pressuregradients within the water do not occur.
The only driving force is the wind stress applied
at the sea surface and frictional coupling between
individual layers of water.
The necessary conditions are that the ocean
must be unbounded in the horizontal direction and
infinitely deep. Also, the wind field over the water
has to be assumed as uniform, that is, of constant
speed and direction everywhere. This will prevent
piling up of water near coasts as well as in the
open sea, and no slope of the sea surface will
develop. Ekman first considered non-accelerated
(stationary) drift currents in such an idealized
ocean.
The equations of motion for this case are
• , A d2v 2co sin u = —
p oz2
(8.38)
, . . A d2u — la, sin d> v = -— 7-—-r
p 8z-
Friction resulting from vertical shearing stresses
only is introduced, and the assumption is made
that the eddy viscosity coefficient, A, is constant.
With the abbreviation
2a, sin 0 = a- (8.39)
and with the first equation in (8.38) multiplied by
i = V—1, it follows that
'S = ia2“ (8.40)
The second equation in (8.38) can be written
d'2u
dl2 (8.41)
Since u and v depend only on z, total differentials
have been introduced in eqs. (8.40) and (8.41).
The equation of continuity is evidently satisfied
because u and v are independent of x and y.
The sum of eq. (8.40) and eq. (8.41) is
d2w
dz2
= ia- w (8.42)
where w = u -+- iv.t
The general solution of eq. (8.42) is
w = AeaVTz + Be-a^Tz (8.43)
where A = C{eic, , B — C2e~ici are complex con¬
stants. Separation of the real and the imaginary
part in eq. (8.43) yields the velocity components
z + ci) u = CxeW'rt'** cos
+ C2e-(ws/2)zCOs (^7y z + czj
v = Ci efa/v'D 2 sjn z +
(8.44)
Z + c2)
The four constants C,, C2, c,, c2 have to be deter¬
mined from the boundary conditions.
The lower boundary condition is that the velocity
becomes zero for infinitely deep water (z = 00).
It is obvious from eqs. (8.44) that C, must be equal
to zero in order to satisfy this condition. Thus,
the first term on the right-hand side of eqs. (8.44)
vanishes for both u and v.
At the upper boundary a constant wind stress
is applied to the sea surface. For simplicity, assume
that the horizontal xy-plane is oriented in such a
way that the wind blows in the ^-direction only.
Thus, if tx and ry are the two components of a
horizontal wind stress at the sea surface, tx =
—(A du/dz)^0 = 0, and ry = —(A dv/dz)^0.
Differentiation of the last terms on the right-
hand side of eqs. (8.44) with respect to z yields
du/dz and dv/dz. From the boundary condition
rx = 0 at z = 0, it follows that
\Tz) 2=0 = “ Ca 7T(sin Cs + cos Cs) = 0
which can be satisfied only with c, = —45°.
C,e~(a/v/T) * sin
v^T
fThis is not the vertical velocity component.
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
Similarly, the boundary condition ry =
—(A dv/dz)z=0 requires that
(S,-0 = ~ Ca ^2 (C0S 45° + Sin 45°} = - A
and hence C2 = Ty/Aa.
With these constants, and a/V 2 — */pco sin cj>/A
according to eq. (8.39), the velocity components of
a pure drift current as a function of depth become
u = V0e~(!r/J})z cos (450 7zr
D
v = V0e~^IDS>2 sin (45° 7t
D
where
D = n J-4—-r (8.46)
y pco sin 4>
In eqs. (8.45)
Vo = C2 = r/Aa (8.47)
represents the velocity of the surface current. The
subscript for r can be dropped if it is understood
that the jp-axis is oriented in the wind direction.
From eqs. (8.45) it is seen that for the sea surface
(z = 0), u = V0 cos 45° and v = V0 sin 45°. Hence,
the surface current vector, V0, points in a direction
45° cum sole to the wind direction. This means that
in the Northern Hemisphere the surface water
moves in a direction 45° to the right when one is
facing in the direction toward which the wind blows,
and in the Southern Hemisphere it is deflected 45°
to the left.
In the form of eqs. (8.45) the result is applicable
only in the Northern Hemisphere, because in the
Southern Hemisphere the latitude cf> is negative,
and D according to eq. (8.46) would be imaginary.
In order to obtain a solution that is valid in the
Southern Hemisphere the direction of the j-axis
must be reversed.
At the depth, D, it follows from eqs. (8.45) for
z = D that
(u) o = V0e n cos (45° — 7r)
(8.48)
(v) D = V0e 71 sin (45° — 7r)
Equations (8.48) indicate that at this depth the
current vector has decreased to e~n times the sur¬
face velocity, or to about of the value at the
surface. Moreover, the current direction has
changed, and at depth D the current is exactly
opposite to the surface current. From eqs. (8.45)
it is seen that the current vector between the surface
and deeper layers turns continuously cum sole
while the velocity decreases exponentially.
A schematic vector representation of pure wind-
driven currents as a function of depth is given in
Figure 8.5. The arrows show the velocity and
direction of current vectors at depths of equal
intervals. Projected on a horizontal plane, the end
points of the current vectors form a logarithmic
spiral, the Ekman spiral. Although in this model
the velocity of a drift current approaches zero
asymptotically for infinitely deep water, by far the
more important currents are found above the
depth D. The depth was called by Ekman the
Figure 8.5 Ekman spiral for pure wind-driven cur¬
rents projected on a horizontal plane. V0 is the surface
velocity vector deviated by 45° to the right of the wind
vector (Northern Hemisphere). [After Ekman (1905).]
“depth of frictional influence.” It should be noted
that D, according to eq. (8.46), is independent of
the wind stress. It does, however, increase with
increasing eddy viscosity coefficient and with de¬
creasing latitude. At the equator, D approaches
infinity.
From eqs. (8.47), (8.46), and (8.39) it also follows
that the surface velocity of a pure drift current is
proportional to the wind stress, namely
V =_1_- =_*1_
0 s/2Ap co sin (f> a/ 2 Dpco sin (f)
(8.49)
At the equator, with sin OO ?
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 193
194
even an infinitely deep ocean is not “deep” enough
to satisfy the lower boundary condition that
» = r = 0atz=oo.
Of particular significance is the total mass trans¬
port of pure drift currents. These are obtained by
multiplying the velocity components u and v by the
density p and integrating over the depth between
z = 0 and z = oo. Hence
C f” j Vn D Ty Sx = p U dz = p !i7-— = -r—r
r J o r Tt V 2 2a> sin (b
(8.50)
Sy = p | ^ v dz = 0
Sx and Sy are the x- and ^-components of a total
mass transport vector 5 = */S% + Si across a
vertical section of 1 cm width. Since Sy = 0, the
total transport in the moving layer of a pure drift
current is directed 90° cum sole to the wind direc¬
tion or, in the Northern Hemisphere, 90° to the
right, and in the Southern Hemisphere, 90° to the
left of the wind. The total mass transport is pro¬
portional to the wind stress and inversely propor¬
tional to the sine of the latitude. It is interesting
to note that the mass transport is independent of
the value of the eddy viscosity in the water, whereas
the surface velocity, V0, depends on A.
A direct application of Ekman’s results, or a
verification of this theory, is difficult for two major
reasons. First of all, pure drift currents that satisfy
the theoretical assumptions made are hardly ever
found in nature. Secondly, the uncertainties in ourpresent knowledge of the “effective” wind stress,
r, and of the “effective” eddy viscosity coefficients
prohibit a thorough comparison of theoretical
results with direct observations.
The order of magnitude of V0 and D can be
estimated, and observations have shown that, at
least in a general way, Ekman’s results agree with
oceanographic evidence. With an average value
of A — 100 [cm-1 gm sec"1] and p ^ 1, D =
36.7/^/sin [meters]. Thus, in middle latitudes, the
depth of the layer of frictional influence is about 50
meters. At a latitude of 5° (A = 100), it has only
increased to 126 meters, as compared to 36.7
meters at the poles. However, close to the equator
D increases rapidly to infinity at 0°.
For an average wind velocity of 10 [m sec-1] the
wind stress is about 3.5 [dynes cm"2]. Again, with
A = 100, p 1, and 2a> sin , w'here the dashed small
portion near the origin represents the only differ¬
ence between the vertical velocity distribution in
the case d = 1.25D and d = 2.5D. Thus, there is
not much difference between a pure drift current
in infinitely deep water and in a water layer where
d = 1.25 D.
The mass transport components Sx and Sy in
the x- and y-direction, respectively, are obtained
from eqs. (8.51) after multiplication with p and
integration between z = 0 and z = d.
u d£
tvD2
p 2 it* A*
cosh 2—^d + cos 2-dL=d — 2 cosh —dcos —2= d
'^2 \f2 */2 */~2
cosh 2 d + cos 2 —%= d
\T2 1
(8.53)
Sv = \avd£ t„ D2
= P^A'
sinh
V"2
d • sin
sT2
cosh 2 cos 2-
Vr2“ '
If the depth d is sufficiently great compared to D,
eqs. (8.53) approach eqs. (8.50), as is easily seen for
d — D. Sy = 0, since sin zr = 0 and
=
rvD* (261 + 23
p2?t2A\ 261 ~ 2a> sin
With d^> D, the value in parentheses approaches 1.
Other Frictional Laws
The assumption of a constant eddy viscosity coef¬
ficient is inadequate. It is reasonable to assume that
in the wind-stirred surface layers the turbulent eddy
viscosity is greater than in deeper layers. Extremely
turbulent motions are caused by breaking of waves
that are generated and maintained by the wind.
Estimates of the “effective” eddy viscosity coeffi¬
cient by Schmidt, Thorade, and Neumann were
mentioned in Chapter 3. All of these estimates
indicate that in the surface layers of the oceans
the eddy viscosity ’increases with increasing wind
speed.
Neumann (1952) has given the following values
of A for the surface layers in a fully developed,
wind-generated wave motion as a function of wind
speed:
Figure 8.6 Vertical structure of a drift current in an
ocean of finite depth projected on a horizontal plane.
The depth, d, is expressed in terms of the thickness of
the upper layer of frictional influence, D. The curve
for d = 2.5D coincides with the curve for d = 1.25D,
with the exception of the small dashed part near the
origin of the x-y coordinate system. [After Ekman
(1905).]
Wind speed [m/sec] 4 6 8 10 14 18
A [cm-1 gr sec-1] 58 161 332 577 1350 2520
These values are derived from an estimate of the
energy balance in fully developed, wind-generated
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 195
waves. Schmidt (1917) and Thorade (1914) used
current observations at different wind speeds to
determine the dependence of A on wind speed.
Careful analysis of such observations gave values
of A at different wind speeds that agree fairly well
with the estimates in the table shown above. It
should, however, be kept in mind that these results
refer to “effective” eddy viscosity coefficients, which
may include frictional effects from both vertical as
well as horizontal shearing stresses.
The dependence of A (effective) on wind speed
for the total energy dissipation in fully generated,
wind-driven wave motion and, probably, for the
total energy dissipation in wind-generated currents,
can be expressed by the empirical relationship
A (w) = 0.1825 x 10~4w5/2 [cm-1 gr sec-1]
where w is the wind velocity in cm/sec.
With these estimates, A at a wind velocity of
10 m/sec would be approximately 600, instead of
100, as was assumed to estimate the surface current
speed V0, in middle latitudes.
If A = 600 instead of 100, the velocity of the
theoretical drift current would be reduced by a
factor of l//v/~6 = 1/2.45. This shows how impor¬
tant it is to determine the turbulent conditions in
the sea in order to attempt to evaluate numerically
theoretical results like those obtained by Ekman.
As will be shown later,observations on drift
currents have indeed indicated that with increasing
wind speed a strong increase of the eddy viscosity
coefficient A has to be assumed.
Ekman has also given a solution for the case
where the eddy viscosity coefficient is proportional
to the square of the velocity difference between
adjacent layers, rather than to the difference itself.
This leads essentially to the same results as for
A = constant. The most important difference is
that the deflection angle at the sea surface between
current and wind is 49.1°, and that the current
becomes zero at a depth of d = 1.25D. The total
mass transport, however, is not at all affected by
the quadratic law of friction, which again indicates
that eqs. (8.50) are independent of the assumption
of friction.
An extension of Ekman’s work in this direction
was also given by Ertel (1937). It leads to deflection
angles different from 45° and to somewhat de¬
formed spirals.
The effect of a decrease of the eddy viscosity
coefficient toward the bottom in shallow water was
demonstrated by Sverdrup (1929). Observations of
wind drift currents on the North Siberian Shelf
over a water depth of 22 meters served to establish
Figure 8.7 Wind-driven currents in shallow water
assuming a constant eddy viscosity (dashed curve) or
an eddy viscosity that decreases toward the bottom
(fully drawn curve). Observed currents are indicated
by crosses. [From Sverdrup, et a/., (1942).]
an empirical relationship between the eddy vis¬
cosity coefficient, A, and the distance, f, from the
bottom. According to Fjeldstad (1929) this relation¬
ship is A = 385[(^ + 0.1)/22.1]3/4. Figure 8.7 pre¬
sents the observed velocities and the corresponding
velocities computed with Fjeldstad’s vertical eddy
viscosity distribution. They are compared with the
velocity distribution computed from Ekman’s equa¬
tions, assuming a constant value of A = 200.
There is no doubt that the assumption of an eddy
viscosity coefficient varying with depth agrees much
better with observations than that of a constant A.
Other investigators (Jeffreys, 1923; Fjeldstad,
1929; Rossby and Montgomery, 1935) also dealt
with the problem of the effect of variable friction
on pure wind drift currents. These studies are all
of great interest and theoretical value, but general
improvements of the original results hinge on a
better understanding of the character of turbulence,
the “effective” eddy viscosity coefficient, and its
dependence on wind speed and on depth in the
oceans. Ekman s original theory for deep water
still appears to give a satisfactory approximation.
This may be, of course, the result of the fact that
very few observations of pure drift currents are
available to test refined theories.
Effects of Stratification
If the density increases with depth, certain modifi¬
cations of Ekman’s original theory have to be
expected. Defant (1927) has shown that in the
196 Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
case of a continuous density increase with depth
the deviations from the homogeneous ocean are
small. Essentially different modifications appear for
abrupt vertical density changes (density discon¬
tinuity surfaces). They are, however, more the
indirect result ot stability effects on the vertical
exchange of momentum. Below the density discon¬
tinuity the vertical eddy viscosity coefficient is
strongly reduced, and the wind effect is confined
essentially to the top layer. This means that the
upper layer will slide over the denser lower layer,
which will be practically unaffected by the wind.
Such conditions were observed during the Nor¬
wegian North Polar Expedition with the Maud
(Sverdrup, 1928, 1929). At a considerable distance
from land an upper layer of constant density was
found over a much heavier bottom layer. The two
layers were separated by a comparatively thin layer
of transition, varying in depth between 25 and 40
meters below the sea surface. The high value of
the eddy viscosity in the upper layer was in sharp
contrast to the extremely low value in the thin,
stable layer of transition.
Nomitsu (1933) has dealt with such problems in
more detail. Instead of u = v = 0 at z = d, the
lower boundary condition is
It is of interest to note that with decreasing thick¬
ness, d, of the upper water layer the angle of deflec¬
tion as well as the current velocity increases. This
is just the opposite of the results obtained from
eqs. (8.51) for finite depth where the lower bound¬
ary condition was u = v = 0 for z — d, at the solid
bottom.
Slope currents and the
elementary current system
It is evident that pure drift currents must be an
extreme rarity in the oceans, since the oceans are
not unbounded and the wind field that produces
drift currents is not uniform. The horizontal water
transport, according to eqs. (8.50), cannot continue
its way indefinitely. Interference of coasts and
changes in the wind field will produce convergences
or divergences of the total horizontal transport of
water in the surface layer. This must result in either
a piling up of water or in a depression of the water
level, depending on how the wind field changes or
how it is directed with respect to the coast lines.
The case of a non-uniform wind field in the open
ocean, far away from coasts, will be considered
first. Figure 8.8(a) shows, schematically, a zonal
boundary between winds blowing from the west
and from the east. This may be verified in the
North Pacific or North Atlantic around 25° lati¬
tude, that is, between the prevailing “Westerlies”
and the Northern Trade Winds. It is obvious from
eqs. (8.50) that at the zonal boundary between both
Figure 8.8 Non-uniform wind field (a), showing west and east winds, respec¬
tively, and (b), the corresponding water transports in the upper layer of frictional
influence, (D), leading to divergences and a convergence. The meridional cross-
section along the line N-S [shown in (c)] indicates a piling up of water in the region
of convergence near 25° latitude, the resulting slope of isobaric surfaces, p, and
the development of a bottom layer of frictional influence of thickness D* with the
anisobaric transports in the opposite direction as found in the upper layer of fric¬
tional influence, D. [As a result of viscous flow, there will also be an anisobaric
transport in the deep layer, between D and D*.]
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 197
198
wind directions a convergence of Ekman’s total
mass transport 5 must occur, because both the
“Westerlies” and the Trade Winds transport the
water to the right when one is looking in the direc¬
tion of the wind [Figure 8.8(b)], The same is true
in the Southern Hemisphere with a transport to
the left when one is looking in the wind direction,
since the “Westerlies” are to the south of the Trade
Winds.
Essentially, the water mass, or volume, transport
of pure drift currents, according to Ekman, occurs
in a relatively shallow upper layer of depth D [eq.
(8.46)]. In Figure 8.8(b) this transport, as produced
by the “Westerlies” and Trade Winds, is indicated
by vectors S, which are proportional to the wind
stress r.
A meridional cross-section along the line N-S
through the zonal belt is shown in Figure 8.8(c).
Between the west and east winds the converging
mass transport around 25° latitude leads to a piling
up of water, and horizontal pressure gradients are
caused by the sloping sea surface. In a homogene¬
ous ocean these pressure gradients must cause
currents between the sea surface and the bottom,
which are superposed on the pure wind drift cur¬
rents. If the water is deep enough the currents
beneath the layer of frictional influence will consist
essentiallyof “slope currents” that, in the case of
a frictionless flow, must be pure geostrophic cur¬
rents. However, stationary conditions would evi¬
dently be impossible in such a model. The anis-
obaric mass transport in the upper layer of fric¬
tional influence must be balanced by the same, but
opposite, anisobaric mass transport in deeper
layers. Since pure geostrophic currents do not occur
in nature, part of this balance will be produced by
the deep current under the influence of its internal
friction. Even with the absence of vertical shearing
stresses there are lateral shearing stresses to be
considered, and frictional forces—for example, in
Figure 8.8(c)—acting in the water column between
the isobaric surfaces px and p3, may at least provide
part of the required balance for the anisobaric flow
in the upper layers of frictional influence. A great
increase of frictional effects, however, can be ex¬
pected when the slope currents reach the bottom.
In Figure 8.8(c) this is shown by arrows in the
bottom layer of frictional influence of thickness
D*, indicating a mass transport from high to low
pressure areas.
Fateral boundaries of the oceans (coasts) will
cause a similar slope of the sea surface if the mass
transport, S, in the layer of frictional influence of
pure drift currents has a component in the direction
of the coast line. With an onshore component the
water must pile up against the coast, and with an
offshore component the sea surface will be lowered
near the coast. Such sea surface slopes produce
slope currents in deeper layers in the same way as
was shown in Figure 8.8 for a non-uniform wind
field in the open ocean.
Ekman’s Solution for Slope Currents
The first solution to the problem of slope currents
as produced by wind drift currents was given by
Ekman (1905). He introduced frictional forces for
the slope currents. However, his assumption was
that these frictional forces result from vertical
shearing stresses only.
The slope current can be treated separately from
the pure wind drift current. Assume that a certain
slope of the sea surface in a homogeneous ocean
of depth d has developed, for example, by the
piling up of water against a coast or in a con¬
vergence between winds of different direction.
Further, assume that the horizontal pressure gradi¬
ent, as produced by the inclination, /3, of the sea
surface against a level surface is everywhere in the
same direction and that the motion is non-acceler-
ated. This motion would then be geostrophic,
except for the influence of friction resulting from
vertical shearing stresses.
For simplicity, put the y-axis in the direction of
the slope of the sea surface (pressure gradient),
and count the x-axis to the right of y. With the
z-axis pointing downward, the hydrodynamic equa¬
tions are
2g> sin cf> u
— 2co sin v
A d2v 1 dp
p dz2 p 8y
— d2»
p dz2
(8.54)
If tan (3 is the slope of the sea surface and, in a
homogeneous ocean, also the slope of isobaric
surfaces in deeper layers, /3 is constant with depth
and
dp
8y — gp tan 5
For very small angles /3, tan /3 % /3, and eqs.
(8.54) can be written
d2v _
dz2
pg@
A
d'2u
dz2
— a-v
(8.55)
In eqs. (8.55), a2 is the same as in eq. (8.39); total
differentials have been introduced since u and v
are functions of z only. For this reason, the equa¬
tion of continuity is also identically fulfilled.
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
With In eqs. (8.59)
and
u = ul + pgfi
a2 A
it follows that
w = Ui -\- iv
d'2w
dzP- = ia-w (8.56)
This differential equation is the same as eq. (8.42).
Thus, the solution given for eq. (8.42) can formally
be used for the solution of eq. (8.56) to obtain
U = Cxe(a/V2)*cos z + cl
C2e~(a/'/^)z cos (7?z + f \*/~2
v = Cle sin sin (p
has a similar meaning to D in eq. (8.46). The
depth D* is called the depth of the bottom layer
of frictional influence.
The curves in Figure 8.9 represent, in a way
similar to those in Figure 8.6, the vertical velocity
distribution in a slope current for water depths
d = 0.25D*, 0.5D*, and 1.25/7*. The dots on each
curve indicate the end points of the velocity vector
Figure 8.9 Vertical structure of a slope current in
a shallow ocean of depth d projected on a horizontal
plane. The depth, d, is expressed in terms of the thick¬
ness of the bottom layer of frictional influence, D*.
The pressure gradient is in the ^-direction. [After
Ekman (1905).]
to be drawn from the origin at equidistant depths
over the bottom. The deeper the water, the more
is the slope current deflected from the direction of
the pressure gradient (dp/dy), while the velocity
increases. The dashed portion near the end of the
curve for d = 1.25D* indicates the only difference
between this curve and the corresponding curve
for d = 2.5D*. Thus, the vertical distribution of
a slope current in the case where d = D* is not
essentially different from the case where d is many
times greater than the thickness of the lower layer
of frictional influence.
The magnitude of D* [eq. (8.60)] is approximately
the same as the magnitude of D, the upper layer
of frictional influence. It is interesting to note that
with the assumption of vertical shearing stresses
only (no lateral friction), the frictional effects on
the slope currents are essentially restricted to a
bottom layer of relatively small thickness.
If the depth of the water, d, equals the depth
/)*, it follows from eqs. (8.59) for the sea surface
at z = 0 that the surface velocity components are
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 199
200
"•=2^~2^>
n (8-61)
v0 = 0
This is essentially the velocity of a geostrophic
current. In this case, the velocity component v0
is exactly zero, since sin (a/a/~2) d = sin it = 0 in
eq. (8.59) for z — 0. With ratios other than d/D* =
1, the v component fluctuates between positive and
negative values, continuously decreasing as the
ratio d/D* increases. In the case of infinitely deep
water the curve representing the slope current is
very similar to the logarithmic spiral for pure wind
drift currents, except that the current vectors at
different depths start from the opposite end of the
curve. Immediately over the bottom, the bottom
current starts from zero forming an angle of 45°
with the horizontal pressure gradient.
The vertical velocity distribution of a slope cur¬
rent in deep water is also shown in Figure 8.10 by
a block diagram of vectors. The bottom layer is
occupied by the bottom current in which the ve¬
locity decreases exponentially with depth. If the
wateris infinitely deep, the end points of the current
vectors, when projected on a plane, form a logarith¬
mic spiral. In layers sufficiently high above the
bottom, the current follows essentially the direction
of the isobars. This geostrophic flow was called by
Ekman the uniform “mid-water current.” It is seen
that this mid-water current (or deep current) can-
Figure 8.1 0 Block diagram of vectors showing the
vertical distribution of a slope current in deep water.
[After Ekman (1905).]
not contribute to the equalization of sea surface
slopes. This is only possible in the bottom layer
where the bottom current has a component in the
direction of the pressure gradient (anisobaric com¬
ponent).
The mass transport components, Mx and My,
in the x- and y-direction of a slope current, are
obtained by vertical integration of eqs. (8.59) be¬
tween z — 0 and z = d, after multiplication with
the density p. This yields
AT
D*g/3
4tzt(x) sin 0
sinh 2-n: + sin 2-rt
cosh 2tt ~
My p D*gj3
sinh 27r — sin 2n
D*
- d
COS 27t jy* j
d_
D*
4-rtco sin 0 , - d . „ d
COSh Z7t Jy* + COS lit Jy,
(8.62)
It is seen from eqs. (8.62) that Mv, the mass
transport component in the direction of the pres¬
sure gradient, does not increase indefinitely with
the water depth d. As d increases it approaches the
limit
(8.63)
The mass transport component Mx, however,
increases approximately proportional to d. With
d > D*, sinh 2% (d/D*) = cosh 2?r (d/D*) = n. In
the case d = D*, n = 265 and
AT. sj p[-gd/3
“\2co sin 0
D*g/3 \
47ta> sin 0/
(8.64)
Without friction, the mass transport of a slope cur¬
rent of depth d would be pua-d — pg/3d/2a>-sin 0,
where ug is the velocity of a geostrophic cur¬
rent produced by a slope /3 of isobaric surfaces
against level surfaces [eq. (7.69)]. Thus, the first
term in eq. (8.64) for Mx represents the mass trans¬
port of a geostrophic current parallel to the is¬
obars, and the second term represents Mv [eq
(8.63)].
Other Assumptions about Bottom Friction
Ekman’s theory is based on the assumption of a
constant eddy viscosity coefficient between bottom
and surface. Although the theory was first devel¬
oped for ocean currents, the results have been
used extensively in meteorology, and Ekman sug¬
gested a meteorological application as early as
1905. The deflection of the surface wind to the
right with increasing height, and the approach to
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations
a nearly geostrophic flow above a layer of frictional
influence, was generally explained by Ekman’s
results. However, in the lowest layers, near the
ground, significant differences between the theoret¬
ical Ekman spiral and the observations become
evident. They indicate that the assumption of a
constant friction coefficient is inadequate. Ekman
(1928) himself realized this inadequacy and intro¬
duced a different frictional law for a boundary
layer right above the bottom, the so-called “skin
layer.” Within the skin layer the velocity changes
approximately linearly with height and without
change of direction, from zero at the bottom to a
velocity cs at its upper limit. Ekman made the
assumption that the water body just above the
skin layer flows with a finite velocity, compared to
the top of the skin layer, and experiences a bound¬
ary friction proportional to the “gliding” velocity.
Again, with constant friction coefficients in both
layers, although with very much smaller coeffi¬
cients in the skin layer, Ekman arrived at a modified
vertical velocity structure in the bottom current.
This is shown in Figure 8.11. The velocity vectors
at different heights over the bottom are to be drawn
Figure 8.11 Vertical structure in a bottom current
(or at an interface) with a skin layer (O — A) of differ¬
ent friction above the bottom projected on a horizon¬
tal plane. [After Ekman (1932).]
from O to points APB on the heavily-drawn curve.
The vector cs represents the velocity at the upper
limit of the skin layer at point A. When projected
on a horizontal plane, a logarithmic spiral, APB,
connects the end points of the velocity vectors
above the skin layer. The (constant) velocity of the
deep current, cg, therefore, is shown by the vector
OB, and cs (from O to A) is the “gliding velocity”
over the bottom. This velocity vector cs forms with
the deep current an angle a = K, where A" is a constant if
all other factors are kept constant. Much more
needs to be known about the variation of a in
nature before essential improvements of Ekman’s
theory can be expected. Other attempts to im¬
prove Ekman’s original results have been made by
Prandtl (1942), Rossby (1932), and Rossby and
Montgomery (1935).
Ekman’s Elementary Current System
Consider a homogeneous ocean of constant depth,
d, bounded by an infinitely long straight coast.
The only currents that are possible in this ocean
are wind drift and slope currents. For simplicity,
put the coordinate system with its y-axis perpen¬
dicular to the coast. Next, assume that a uniform
wind is blowing in the direction of the positive
x-axis and that stationary conditions have been
established. Under the action of the wind, pure
drift currents will produce a mass transport per¬
pendicular to the coast and a slope of the sea sur¬
face will develop such that the sea surface rises
toward the coast. According to Ekman, in a deep
ocean the resulting current system will consist of
three components:
(a) The bottom current between the bottom and
the height D* over the bottom (lower layer of
frictional influence). This current is deflected from
45° to 90° to the right of the pressure gradient.
(b) The deep current (or mid-water current, ac¬
cording to Ekman) between the height D* over
the bottom and the surface if there is no wind.
However, with a wind blowing, a pure wind drift
current would develop, essentially between the sea
surface and the depth D (depth of upper layer of
frictional influence).
(c) The surface layer current, which is, therefore,
a superposition of the deep current and the pure
drift current in every layer of depth D. Theoreti¬
cally, the pure drift current extends infinitely deep;
however, its contribution beneath the layer of fric¬
tional influence is insignificant.
This current system, consisting of a bottom
current, a deep current, and a surface layer current,
is called Ekman's elementary current system. Figure
8.12 represents this current system, and shows the
three layers in a vertical section of total depth d, as
well as the vertical distribution of velocity vectors
in each layer when projected on a horizontal plane.
The figure applies to the Northern Hemisphere.
With stationary currents and, therefore, with a
stationary slope of the sea surface, the total an-
isobaric mass transport in the bottom current must
be equal but opposite to the total anisobaric mass
Currents and Frictional Forces, Horizontal Wind-Driven Currents, Thermohaline Circulations 201
Figure 8.1 2 Ekman’s elemen¬
tary current system, (a) Pure
drift current at surface (z = 0),
(b) actual surface current for
z = 0 [vector (a) + vector (c)],
(c) deep current (geostrophic),
and (d) bottom current.
transport in the surface layer current. The deep
current shown by the heavy vector is parallel to the
isobars with the higher pressure to the right.
In a stationary elementary current system the
continuity