Prévia do material em texto
<p>TRANSMISSION</p><p>OPERATION AND</p><p>DIAGNOSTICS</p><p>(TE27 AND TE32) WITH</p><p>FULL FLOW VALVE</p><p>PART NO. 4046342 1300 SRM 1566</p><p>SAFETY PRECAUTIONS</p><p>MAINTENANCE AND REPAIR</p><p>• The Service Manuals are updated on a regular basis, but may not reflect recent design changes to the</p><p>product. Updated technical service information may be available from your local authorized Hyster®</p><p>dealer. Service Manuals provide general guidelines for maintenance and service and are intended for</p><p>use by trained and experienced technicians. Failure to properly maintain equipment or to follow</p><p>instructions contained in the Service Manual could result in damage to the products, personal injury,</p><p>property damage or death.</p><p>• When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened, and</p><p>that the load being lifted is balanced. Make sure the crane, cables, and chains have the capacity to</p><p>support the weight of the load.</p><p>• Do not lift heavy parts by hand, use a lifting mechanism.</p><p>• Wear safety glasses.</p><p>• DISCONNECT THE BATTERY CONNECTOR before doing any maintenance or repair on electric lift</p><p>trucks. Disconnect the battery ground cable on internal combustion lift trucks.</p><p>• Always use correct blocks to prevent the unit from rolling or falling. See HOW TO PUT THE LIFT</p><p>TRUCK ON BLOCKS in the Operating Manual or the Periodic Maintenance section.</p><p>• Keep the unit clean and the working area clean and orderly.</p><p>• Use the correct tools for the job.</p><p>• Keep the tools clean and in good condition.</p><p>• Always use HYSTER APPROVED parts when making repairs. Replacement parts must meet or</p><p>exceed the specifications of the original equipment manufacturer.</p><p>• Make sure all nuts, bolts, snap rings, and other fastening devices are removed before using force to</p><p>remove parts.</p><p>• Always fasten a DO NOT OPERATE tag to the controls of the unit when making repairs, or if the unit</p><p>needs repairs.</p><p>• Be sure to follow the WARNING and CAUTION notes in the instructions.</p><p>• Gasoline, Liquid Petroleum Gas (LPG), Compressed Natural Gas (CNG), and Diesel fuel are</p><p>flammable. Be sure to follow the necessary safety precautions when handling these fuels and when</p><p>working on these fuel systems.</p><p>• Batteries generate flammable gas when they are being charged. Keep fire and sparks away from the</p><p>area. Make sure the area is well ventilated.</p><p>NOTE: The following symbols and words indicate safety information in this</p><p>manual:</p><p>WARNING</p><p>Indicates a hazardous situation which, if not avoided, could result in death</p><p>or serious injury.</p><p>CAUTION</p><p>Indicates a hazardous situation which, if not avoided, could result in minor</p><p>or moderate injury and property damage.</p><p>On the lift truck, the WARNING symbol and word are on orange back-</p><p>ground. The CAUTION symbol and word are on yellow background.</p><p>©2017 HYSTER COMPANY</p><p>TABLE OF CONTENTS</p><p>Series Code / Model Designation Reference Table ................................................................................................ 1</p><p>General .....................................................................................................................................................................1</p><p>Description of Operation .........................................................................................................................................2</p><p>General .................................................................................................................................................................2</p><p>Operation ................................................................................................................................................................. 4</p><p>Hydraulic Operation ............................................................................................................................................4</p><p>Anti-Drain ............................................................................................................................................................5</p><p>Cooling and Lubrication ......................................................................................................................................7</p><p>Control System ........................................................................................................................................................ 7</p><p>General .................................................................................................................................................................8</p><p>APC Controller .................................................................................................................................................... 8</p><p>Self Test ........................................................................................................................................................... 8</p><p>Protection Modes ............................................................................................................................................. 8</p><p>Limp Home Mode .........................................................................................................................................8</p><p>Shut Down Mode ..........................................................................................................................................8</p><p>Transmission Exceed Codes ........................................................................................................................8</p><p>Fault Codes Displayed on Instrument Cluster ..............................................................................................9</p><p>Description ................................................................................................................................................... 9</p><p>Fault Log Mode ................................................................................................................................................9</p><p>Access ........................................................................................................................................................... 9</p><p>Exit ............................................................................................................................................................. 10</p><p>Clear ........................................................................................................................................................... 10</p><p>Fault Rectification .........................................................................................................................................10</p><p>Transmission Control Valve ............................................................................................................................. 10</p><p>Pressure Check .............................................................................................................................................. 13</p><p>Pressure Specifications ..................................................................................................................................... 14</p><p>Pressure, Speed, and Temperature Sensors .................................................................................................... 14</p><p>Pressure Sensors ........................................................................................................................................... 15</p><p>Test .............................................................................................................................................................15</p><p>Speed Sensor ..................................................................................................................................................15</p><p>Test .............................................................................................................................................................17</p><p>Temperature Sensors .................................................................................................................................... 18</p><p>Test .............................................................................................................................................................18</p><p>A19 J2 Shift Lever Reverse hi/lo</p><p>6.43 DIGIN6 B13 L3 Start in 2nd Gear hi/lo</p><p>7.44 DIGIN7 B14 M3 Automatic/Manual Mode hi/lo</p><p>8.45 DIGIN8 B15 N3 Park Brake ON/OFF hi/lo</p><p>9.46 DIGIN9 B16 P3 OPEN lo</p><p>Figure 23. Digital Input Test</p><p>Figure 24. Display Segment Numbers</p><p>In the example shown in Figure 25, the segments 1,</p><p>4, and 5 are ON, indicating that DIGIN1, DIGIN4,</p><p>and DIGIN5 are active. By moving the selector</p><p>lever, different segments will be switched ON.</p><p>Press and hold the S button to scroll to the</p><p>individual digital inputs. The display will show the</p><p>logic input number with the matching APC200 wire</p><p>number. The example in Figure 26 shows that</p><p>DIGIN0 relates to APC200 wire A12.</p><p>When releasing the S button, the display shows</p><p>either hi’ or lo’. When the lever switch is making a</p><p>connection or has a short circuit, hi’ is shown. When</p><p>the lever switch does not connect or has an open</p><p>circuit, lo’ is shown. Unsupported connections will</p><p>show lo’.</p><p>Pressing the S button after 9.46 returns the display</p><p>to dinP’.</p><p>Figure 25. Active Digital Inputs</p><p>Figure 26. Digital Input Code</p><p>1300 SRM 1566 APC200 Display Information</p><p>29</p><p>ANALOG INPUT TEST</p><p>The APC200 has seven analog resistance inputs,</p><p>which measure the actual resistance of the sensors</p><p>listed in Table 7.</p><p>After the display has shown AinP’ (see Figure 27),</p><p>push and release the S button. The display will</p><p>show the value in kilo Ohm in sequence of each of</p><p>the four inputs. Values below 1 kOhm are shown as</p><p>0’. Each input value is separated by a dot. See</p><p>Figure 28.</p><p>Press and hold the S button to scroll to the</p><p>individual analog inputs. The display will show the</p><p>logic input number with the matching APC200 wire</p><p>number. The first input shows ANI0 and APC200</p><p>wire A11.</p><p>When releasing the S button, the display shows the</p><p>resistance value in Ohms. Pressing the S button</p><p>after 6.36 returns the display to AinP.’ See</p><p>Figure 27.</p><p>Table 7. Analog Input Test</p><p>Code Wire</p><p>Name</p><p>APC200</p><p>Wire Nr</p><p>APC200</p><p>Pin Nr</p><p>Wire</p><p>Description Output</p><p>0.11 ANI0 A11 A2 Pressure Feedback Switch + Ohm</p><p>1.28 ANI1 A28 H3 Transmission Temperature Ohm</p><p>2.29 ANI2 A29 J3 Converter Out Temperature Ohm</p><p>3.47 ANI3 B17 R3 Inching Pedal Signal Ohm</p><p>4.32 ANI4 B02 M1 Inching Pedal Ohm</p><p>5.34 ANI5 B04 P1 open</p><p>6.36 ANI6 B06 S1 open</p><p>Figure 27. Analog Input Test</p><p>Figure 28. Analog Resistance Values</p><p>SPEED SENSOR TEST</p><p>The APC200 has four speed sensor inputs which</p><p>represent the number of teeth that pass the sensor</p><p>per second (see Table 8). After the display has</p><p>shown SPd’ (see Figure 29), push and release the S</p><p>button. The display will show the value in kilo-</p><p>Ohms in sequence of each input. Each value is</p><p>separated by a dot.</p><p>Figure 29. Speed Sensor Test</p><p>Press and hold the S button to scroll to the</p><p>individual analog inputs. The display will show the</p><p>logic input number with the matching APC200 wire</p><p>number. The first sensor is indicated by 0.22,’</p><p>meaning that sensor SS0 relates to APC200 wire</p><p>A22.</p><p>When releasing the S button, the display shows a c’</p><p>to indicate a current type sensor, and a dot and</p><p>three digits to indicate the frequency in kHz.</p><p>Figure 30 shows a frequency of 0.933 kHz. Pressing</p><p>the S button after 3.41 returns the display to SPd’.</p><p>Figure 30. Measured Frequency</p><p>APC200 Display Information 1300 SRM 1566</p><p>30</p><p>Table 8. Speed Sensor Test</p><p>Code Wire</p><p>Name</p><p>APC200</p><p>Wire Nr</p><p>APC200</p><p>Pin Nr</p><p>Wire</p><p>Description Output</p><p>0.22 SSO+ A22 B3 Drum Speed Sensor + kHerz</p><p>1.24 SS1+ A24 D3 Output Speed Sensor + kHerz</p><p>2.26 SS2+ A26 F3 Engine Speed Sensor + kHerz</p><p>3.41 SS3+ B11 R2 Turbine Speed Sensor + kHerz</p><p>OUTPUT TEST</p><p>The Output Test Group shows the outputs to the</p><p>VFS solenoids and to the ON/OFF solenoids. After</p><p>the display has shown outP’ (see Figure 31), push</p><p>and release the S button. The display indicates the</p><p>active outputs by switching ON certain segments of</p><p>the display. The numbered segments 0 - 3 represent</p><p>the outputs for VFS0 - VFS3. Segments 4 - 6 are not</p><p>used. Segments 7 - 10 represent the outputs for DO0</p><p>- DO3.</p><p>Press and hold the S button to scroll to the</p><p>individual outputs. The display will show the logic</p><p>reference number with the matching APC200 wire</p><p>number. The first output is indicated by 0.2’,</p><p>meaning that VFS0 relates to APC200 wire A02.</p><p>When releasing the S button, the display shows</p><p>either a value for VFS solenoids, or hi’/lo’ for</p><p>ON/OFF solenoids. The value shown for VFS</p><p>solenoids is in mA. When the solenoid is activated,</p><p>hi’ is shown. When the solenoid is NOT activated, lo’</p><p>is shown.</p><p>If an output is currently at fault, the respective</p><p>segment in the overview screen blinks slowly. On</p><p>the output specific screen the display alternates</p><p>between mA or hi’/lo’, and a fault type. Fault types</p><p>used are Open, Short, Curr, or Oor (out of range).</p><p>Pressing the S button after 10.20 returns the</p><p>display to SPd’.</p><p>Figure 31. Output Test</p><p>Table 9. Output Test</p><p>Code Wire</p><p>Name</p><p>APC200</p><p>Wire Nr</p><p>APC200</p><p>Pin Nr</p><p>Wire</p><p>Description Output</p><p>Output Test Variable Force Solenoids</p><p>0.2 VFSO+ A02 B1 VFS Forward Hi Side Out mA</p><p>1.4 VFS1+ A04 D1 VFS 2nd VFS Hi Side Out mA</p><p>2.6 VFS2+ A06 F1 VFS Rev Hi Side Out mA</p><p>3.8 VFS3+ A08 H1 VFS 1st/3rd Hi Side Out mA</p><p>4.31 VFS4+ B01 L1 OPEN —</p><p>5.33 VFS5+ B03 N1 OPEN —</p><p>6.35 VFS6+ B05 R1 OPEN —</p><p>Output Test ON/OFF Solenoids</p><p>7.10 DO0 A10 K1 Total Neutral Solenoid + hi/lo</p><p>8.15 DO1 A15 E2 OPEN lo</p><p>9.16 DO2 A16 F2 1st/3rd Selector Solenoid hi/lo</p><p>10.20 DO3 A20 K2 Total Neutral Solenoid − hi/lo</p><p>1300 SRM 1566 APC200 Display Information</p><p>31</p><p>VOLTAGE TEST</p><p>After the display has shown Volt’ (see Figure 32),</p><p>push and release the S button to scroll to one of the</p><p>three measured voltages:</p><p>• VP’ - Permanent Voltage as measured on</p><p>APC200 wire A01.</p><p>• VS’ - Switched Voltage as measured on</p><p>APC200 wire B12.</p><p>• VSEn’ - Sensor Voltage as measured at any</p><p>analog input.</p><p>Pressing the S button after VSEn’ returns the</p><p>display to Volt’.</p><p>Figure 32. Voltage Test</p><p>Table 10. Voltage Test</p><p>Code Wire</p><p>Name</p><p>APC200</p><p>Wire Nr</p><p>APC200</p><p>Pin Nr</p><p>Wire</p><p>Description Output</p><p>VP PPWR A01 A1 Permanent Battery + 24.0 Volt</p><p>VS SPWR B12 S2 Switched Battery + 24.0 Volt</p><p>Table 11. APC200 Wire Number to Hyster Wire Number Conversion</p><p>APC200</p><p>Wire Nr</p><p>Wire</p><p>Name Color APC200</p><p>Pin Nr</p><p>Wire</p><p>Description Output</p><p>A01 PPWR red A1 Permanent Battery + 24.0 Volt</p><p>A02 VFS0+ white B1 VFS Forward Hi Side Out mA</p><p>A03 VFS0 green C1 VFS Forward Lo Side Out mA</p><p>A04 VFS1+ white D1 VFS 2nd VFS Hi Side Out mA</p><p>A05 VFS1 green E1 VFS 2nd VFS Lo Side Out mA</p><p>A06 VFS2+ white F1 VFS Rev Hi Side Out mA</p><p>A07 VFS2 green G1 VFS Rev Lo Side Out mA</p><p>A08 VFS3+ white H1 VFS 1st/3rd Hi Side Out mA</p><p>A09 VFS3 green J1 VFS 1st/3rd Lo Side Out mA</p><p>A10 DO0 white K1 Total Neutral Solenoid + hi/lo</p><p>A11 ANI0 white A2 Pressure Feedback Switch + Ohm</p><p>A12 DIGIN0 white B2 Shift Lever 1st hi/lo</p><p>A13 DIGIN1 white C2 Shift Lever 2nd hi/lo</p><p>A14 DIGIN2 white D2 Seat Occupied, Switch Relay hi/lo</p><p>A15 DO1 E2 Open</p><p>A16 DO2 white F2 1st/3rd Selector Solenoid hi/lo</p><p>A17 DIGIN3 G2 Open</p><p>APC200 Display Information 1300 SRM 1566</p><p>32</p><p>Table 11. APC200 Wire Number to Hyster Wire Number Conversion (Continued)</p><p>APC200</p><p>Wire Nr</p><p>Wire</p><p>Name Color APC200</p><p>Pin Nr</p><p>Wire</p><p>Description Output</p><p>A18 DIGIN4 white H2 Shift Lever Forward hi/lo</p><p>A19 DIGIN5 white J2 Shift Lever Reverse hi/lo</p><p>A20 DO3 white K2 Total Neutral Solenoid - hi/lo</p><p>A21 GND black A3 APC200 Ground Volt</p><p>A22 SS0+ white B3 Drum Speed Sensor + kHerz</p><p>A23 SS0- green C3 Drum Speed Sensor - kHerz</p><p>A24 SS1+ white D3 Output Speed Sensor + kHerz</p><p>A25 SS1- green E3 Output Speed Sensor - kHerz</p><p>A26 SS2+ white F3 Engine Speed Sensor + kHerz</p><p>A27 SS2- green G3 Engine Speed Sensor - kHerz</p><p>A28 ANI1 white H3 Transmission Temperature Ohm</p><p>A29 ANI2 white J3 Converter Out Temperature Ohm</p><p>A30 GND black K3 Ground Ohm</p><p>B01 VFS4+ L1 Open</p><p>B02 ANI4 orange M1 Inching Pedal Ohm</p><p>B03 VFS5+ N1 Open</p><p>B04 ANI5 P1 Open</p><p>B05 VFS6+ R1 Open</p><p>B06 ANI6 S1 Open</p><p>B07 CAN L green L2 CAN Low</p><p>B08 CAN H yellow M2 CAN High</p><p>B09 RXD N2 Open</p><p>B10 TXD P2 Open</p><p>B11 SS3+ white R2 Turbine Speed Sensor + kHerz</p><p>B12 SPWR red S2 Switched Battery + 24.0 Volt</p><p>B13 DIGIN6 white L3 Start in 2nd Gear hi/lo</p><p>B14 DIGIN7 white M3 Automatic/Manual Mode hi/lo</p><p>B15 DIGIN8 white N3 Park</p><p>Brake ON/OFF hi/lo</p><p>B16 DIGIN9 P3 Open</p><p>B17 ANI3 white R3 Inching Pedal Signal Ohm</p><p>B18 GND black S3 Ground Volt</p><p>1300 SRM 1566 APC200 Display Information</p><p>33</p><p>CALIBRATION GROUP</p><p>Calibration Mode</p><p>Figure 33 schematically shows the procedure to</p><p>enter the calibration mode. The only relevant modes</p><p>are under trAn (clutch filling calibration), hEAt</p><p>(heating the transmission), and brAH (inching</p><p>sensor calibration). See Figure 34. To enter the</p><p>calibration mode, press and hold the S button, and</p><p>turn the key switch to ON. During the first 15</p><p>seconds, the display will show 8888’. Release the S</p><p>button after 15 seconds when the display shows</p><p>trAn’.</p><p>Figure 33. Calibration Mode</p><p>Figure 34. Entering Calibration Mode</p><p>Clutch Filling Calibration</p><p>NOTE: DO NOT interfere with the calibration.</p><p>Activating any controls or components will stop the</p><p>calibration mode before completion.</p><p>1. Apply the parking brake.</p><p>2. Block the drive tires.</p><p>3. Make sure the transmission temperature is at</p><p>least 60°C (140°F).</p><p>4. Make sure the shift lever is in NEUTRAL or</p><p>REVERSE for lift trucks with a shift lever.</p><p>5. Make sure the MONOTROL® pedal is in</p><p>REVERSE for lift trucks with a MONOTROL®</p><p>pedal.</p><p>6. Press and hold the S button, and turn the key</p><p>switch to the ON position. During the first 15</p><p>seconds, the display will show 8888’. Release</p><p>the S button after 15 seconds when the display</p><p>shows trAn’:</p><p>NOTE: Keep engine speed at idle.</p><p>7. Start the engine.</p><p>8. Push the S button once. When all above</p><p>conditions are met, the APC200 display will</p><p>show:</p><p>9. The automatic calibration starts when the</p><p>forward/reverse lever or the MONOTROL®</p><p>pedal is moved into the FORWARD position.</p><p>The screen will display:</p><p>APC200 Display Information 1300 SRM 1566</p><p>34</p><p>10. When the calibration has been completed, the</p><p>APC200 display will show donE’:</p><p>11. Switch the key switch OFF when the APC200</p><p>display indicates that the calibration has been</p><p>completed. Observe the display and wait until</p><p>no segments are illuminated. When the display</p><p>remains OFF, the new calibration has been</p><p>entered into the APC200 memory. The new</p><p>calibration settings will be lost if the key is</p><p>switched ON too early.</p><p>Heat Up Mode</p><p>The heat up mode provides a convenient way to</p><p>quickly heat the transmission for test and</p><p>calibration purposes. During the heat up mode, only</p><p>the highest gear is selected and the inputs from the</p><p>parking brake and the brake pedal position are</p><p>ignored.</p><p>1. Press and hold the S button, and turn the key</p><p>switch to the ON position. During the first 15</p><p>seconds, the display will show 8888’. Release</p><p>the S button after 15 seconds when the display</p><p>shows trAn’.</p><p>2. Start the engine.</p><p>3. Press the M button once and release. The word</p><p>hEAt’ will show:</p><p>4. Press the S button again and release. The</p><p>actual transmission sump temperature will be</p><p>shown:</p><p>5. Apply the service brakes.</p><p>6. Place the MONOTROL® pedal or the shift</p><p>lever in the FORWARD position.</p><p>7. Push the throttle for approximately 15 seconds.</p><p>8. Place the shift lever in NEUTRAL or the</p><p>MONOTROL® pedal in REVERSE.</p><p>9. Run the engine at 1300 rpm for approximately</p><p>15 seconds in NEUTRAL.</p><p>10. Decelerate the engine to idle.</p><p>11. Repeat Step 6 through Step 10 until the</p><p>APC200 display shows a temperature above</p><p>60°C (140°F).</p><p>12. Push the M button to scroll to the desired</p><p>calibration mode. For a clutch calibration,</p><p>scroll until 'tRan' is displayed.</p><p>Inching Pedal Sensor Calibration</p><p>Inching Pedal Sensor Adjustment</p><p>NOTE: Before calibrating the inching pedal sensor,</p><p>the inching pedal must be adjusted correctly. See</p><p>Pedal and Sensor Adjustment for Braking and</p><p>Inching for B/C917, G/H117 and C/D222..</p><p>1. Press and hold the "S" button, and turn the key</p><p>switch to the ON position. During the first 15</p><p>seconds, the display will show:</p><p>2. Release the "S" button after 15 seconds when</p><p>the display shows:</p><p>3. Push the M button until the APC200 display</p><p>shows analog input:</p><p>1300 SRM 1566 APC200 Display Information</p><p>35</p><p>4. Push the S button three times. The display will</p><p>show 0.11, 1.28, 2.29, and a value. Pushing the</p><p>S button another time changes the display to</p><p>03.47. Releasing the button shows the value in</p><p>Ohms for the inching pedal sensor (for</p><p>example: 0.652).</p><p>NOTE: The voltage reading of the inching pedal</p><p>sensor will be shown after a 1-2 second delay.</p><p>5. Check the voltage reading of the inching pedal</p><p>sensor. The reading must be between 0.600 and</p><p>0.700 mV when the pedal is in the pedal up</p><p>position.</p><p>6. If the reading is not between 0.600 and 0.700</p><p>mV, adjust the inching pedal sensor until the</p><p>reading is within specifications.</p><p>7. Turn the key switch to the OFF position to exit</p><p>the APC200 test function group.</p><p>Inching Pedal Sensor Calibration</p><p>NOTE: Calibration will fail under the following</p><p>circumstances:</p><p>• Inching sensor adjustment is below 450 mV.</p><p>• During calibration, the voltage at the inching</p><p>pedal sensor does not reach 2,500 mV or</p><p>exceeds 4,000 mV.</p><p>1. Press and hold the "S" button, and turn the key</p><p>switch to the ON position. During the first 15</p><p>seconds, the display will show:</p><p>2. Release the "S" button after 15 seconds when</p><p>the display shows:</p><p>3. Push the M button several times until the</p><p>APC200 display shows brAH’:</p><p>4. Push the S button once to start the inching</p><p>pedal sensor calibration. The APC200 display</p><p>will show:</p><p>5. Push the S button in the pedal up position. The</p><p>APC200 display will show:</p><p>6. Fully depress the inching pedal and press the S</p><p>button again.</p><p>7. When the calibration is complete, the APC200</p><p>display will show donE’:</p><p>NOTE: The calibration procedure must be repeated</p><p>if the key switch is turned ON too early.</p><p>8. Turn the key switch to the OFF position to</p><p>save the calibration settings.</p><p>Observe the APC200 display and wait until no</p><p>segments are illuminated. When the display</p><p>remains OFF, the new calibration has been</p><p>entered into the APC200 memory. The new</p><p>calibration settings will be lost if the key switch</p><p>is turned ON too early.</p><p>APC200 Display Information 1300 SRM 1566</p><p>36</p><p>Torque Specifications</p><p>TORQUE SPECIFICATIONS FOR</p><p>LUBRICATED OR PLATED SCREW</p><p>THREADS</p><p>Table 12. Grade 5</p><p>Nom. Size Fine Thread Coarse Thread</p><p>0.2500 12.2 to 14.9 N•m (9 to 11 lbf ft) 10.8 to 13.6 N•m (8 to 10 lbf ft)</p><p>0.3125 21.7 to 27.1 N•m (16 to 20 lbf ft) 16.3 to 21.7 N•m (12 to 16 lbf ft)</p><p>0.3750 35.2 to 39.3 N•m (26 to 29 lbf ft) 31.2 to 33.9 N•m (23 to 25 lbf ft)</p><p>0.4375 55.6 to 61 N•m (41 to 45 lbf ft) 50.2 to 55.6 N•m (37 to 41 lbf ft)</p><p>0.5000 86.8 to 94.9 N•m (64 to 70 lbf ft) 77.3 to 85.4 N•m (57 to 63 lbf ft)</p><p>0.5625 123.4 to 135.6 N•m (91 to 100 lbf ft) 111.2 to 122 N•m (82 to 90 lbf ft)</p><p>0.6250 173.5 to 191.1 N•m (128 to 141 lbf ft) 153.2 to 168.1 N•m (113 to 124 lbf ft)</p><p>0.7500 302.3 to 332.1 N•m (223 to 245 lbf ft) 271.1 to 298.2 N•m (200 to 220 lbf ft)</p><p>Table 13. Grade 8</p><p>Nom. Size Fine Thread Coarse Thread</p><p>0.2500 14.9 to 17.6 N•m (11 to 13 lbf ft) 12.2 to 14.9 N•m (9 to 11 lbf ft)</p><p>0.3125 38 to 43.4 N•m (28 to 32 lbf ft) 35.2 to 40.7 N•m (26 to 30 lbf ft)</p><p>0.3750 50.2 to 55.6 N•m (37 to 41 lbf ft) 44.7 to 48.8 N•m (33 to 36 lbf ft)</p><p>0.4375 78.6 to 86.8 N•m (58 to 64 lbf ft) 70.5 to 77.3 N•m (52 to 57 lbf ft)</p><p>0.5000 122 to 134.2 N•m (90 to 99 lbf ft) 108.4 to 119.3 N•m (80 to 88 lbf ft)</p><p>0.5625 173.5 to 191.1 N•m (128 to 141 lbf ft) 155.9 to 172.2 N•m (115 to 127 lbf ft)</p><p>0.6250 244 to 268.4 N•m (180 to 198 lbf ft) 215.5 to 237.2 N•m (159 to 175 lbf ft)</p><p>0.7500 427 to 470.4 N•m (315 to 347 lbf ft) 382.3 to 420.2 N•m (282 to 310 lbf ft)</p><p>Table 14. Grades 8.8, 10.9, and 12.9</p><p>Nom. Size</p><p>Grade 8.8 Grade 10.9 Grade 12.9</p><p>Coarse Thread Coarse Thread Coarse Thread</p><p>M5 5 to 6 N•m (3.7 to 4.4 lbf ft) 7 to 8 N•m (5.2 to 5.9 lbf ft) 8 to 10 N•m (5.9 to 7.4 lbf ft)</p><p>M6 8 to 10 N•m (5.9 to 7.4 lbf ft) 12 to 15 N•m</p><p>(8.9 to 11.1 lbf ft)</p><p>13 to 16 N•m</p><p>(9.6 to 11.8 lbf ft)</p><p>M8 20 to 25 N•m</p><p>(14.8 to 18.4 lbf ft)</p><p>30 to 35 N•m</p><p>(22.1 to 25.8 lbf ft)</p><p>35 to 40 N•m</p><p>(25.8 to 29.5 lbf ft)</p><p>M10 40 to 50 N•m</p><p>(29.5 to 36.9 lbf ft)</p><p>60 to 65 N•m</p><p>(44.3 to 47.9 lbf ft)</p><p>65 to 75 N•m</p><p>(47.9 to 55.3 lbf ft)</p><p>M12 68 to 75 N•m</p><p>(50.2 to 55.3 lbf ft)</p><p>100 to 110 N•m</p><p>(73.8 to 81.1 lbf</p><p>ft)</p><p>115 to 130 N•m</p><p>(84.8 to 95.9 lbf ft)</p><p>1300 SRM 1566 Torque Specifications</p><p>37</p><p>Table 14. Grades 8.8, 10.9, and 12.9 (Continued)</p><p>Nom. Size</p><p>Grade 8.8 Grade 10.9 Grade 12.9</p><p>Coarse Thread Coarse Thread Coarse Thread</p><p>M14 110 to 125 N•m</p><p>(81.1 to 92.2 lbf ft)</p><p>150 to 175 N•m</p><p>(110.6 to 129.1 lbf ft)</p><p>180 to 210 N•m</p><p>(132.8 to 154.9 lbf ft)</p><p>M16 170 to 190 N•m</p><p>(125.4 to 140.1 lbf ft)</p><p>240 to 275 N•m</p><p>(177 to 202.8 lbf ft)</p><p>280 to 320 N•m</p><p>(206.5 to 236 lbf ft)</p><p>M20 320 to 360 N•m</p><p>(236 to 265.5 lbf ft)</p><p>450 to 500 N•m</p><p>(331.9 to 368.8 lbf ft)</p><p>525 to 600 N•m</p><p>(387.2 to 442.5 lbf ft)</p><p>M24 570 to 650 N•m</p><p>(420.4 to 479.4 lbf ft)</p><p>800 to 900 N•m</p><p>(590.1 to 663.8 lbf ft)</p><p>900 to 1050 N•m</p><p>(663.8 to 774.4 lbf ft)</p><p>M30 1150 to 1300 N•m</p><p>(848.2 to 958.8 lbf ft)</p><p>1600 to 1800 N•m</p><p>(1180.1 to 1327.6 lbf ft)</p><p>1850 to 2100 N•m</p><p>(1364.5 to 1548.9 lbf ft)</p><p>M36 2000 to 2250 N•m</p><p>(1475.1 to 1659.5 lbf ft)</p><p>2749 to 3149 N•m</p><p>(2027.6 to 2322.6 lbf ft)</p><p>3249 to 3699 N•m</p><p>(2396.3 to 2728.2 lbf ft)</p><p>Table 15. Elastic Stop Nut Torque</p><p>Thread Size Torque</p><p>M10 × 1 8 to 10 N•m (6 to 7 lbf ft)</p><p>M14 × 1.5 10 to 12 N•m (7 to 9 lbf ft)</p><p>M18 × 1.5 34 to 41 N•m (25 to 30 lbf ft)</p><p>M22 × 1.5 48 to 60 N•m (35 to 44 lbf ft)</p><p>M33 × 2 112 to 140 N•m (83 to 103 lbf ft)</p><p>Table 16. O-ring Port Plug Torque Chart</p><p>Thread Size</p><p>NPTF Torque</p><p>9/16 × 18 16 to 20 N•m (12 to 15 lbf ft)</p><p>3/4 × 16 27 to 34 N•m (20 to 25 lbf ft)</p><p>Table 17. Pipe Plug Torque Chart</p><p>Thread Size</p><p>NPTF Torque</p><p>1/16 × 27 7 to 9 N•m (5 to 7 lbf ft)</p><p>1/8 × 27 9 to 14 N•m (7 to 10 lbf ft)</p><p>1/4 × 18 20 to 27 N•m (15 to 20 lbf ft)</p><p>3/8 × 18 34 to 41 N•m (25 to 30 lbf ft)</p><p>1/2 × 14 41 to 47 N•m (30 to 35 lbf ft)</p><p>3/4 × 10 or 14 54 to 61 N•m (40 to 45 lbf ft)</p><p>1 × 11 1/2 68 to 75 N•m (50 to 55 lbf ft)</p><p>1 1/4 × 11 1/2 81 to 88 N•m (60 to 65 lbf ft)</p><p>Table 18. Pipe Plug Torque Chart</p><p>Nominal Size</p><p>Plugs (Permanent Plugs)</p><p>Torque</p><p>M18 × 1.5 6H 34 to 41 N•m (25 to 30 lbf ft)</p><p>M26 × 1.5 6H 61 to 68 N•m (45 to 50 lbf ft)</p><p>Torque Specifications 1300 SRM 1566</p><p>38</p><p>Troubleshooting</p><p>PROBLEM POSSIBLE CAUSE PROCEDURE OR ACTION</p><p>Low clutch pressure. Low oil level.</p><p>Clutch pressure regulating valve</p><p>stuck open.</p><p>Faulty charging pump.</p><p>Broken or worn clutch shaft or</p><p>piston rings.</p><p>Clutch piston bleed valve stuck</p><p>open.</p><p>Fill to proper level.</p><p>Clean valve spool and housing.</p><p>Replace pump.</p><p>Replace piston rings.</p><p>Clean bleed valves thoroughly.</p><p>Low charging pump output. Low oil level.</p><p>Suction screen plugged.</p><p>Defective charging pump.</p><p>Fill to proper level.</p><p>Clean suction pump.</p><p>Replace pump.</p><p>Overheating Worn oil sealing rings.</p><p>Worn charging pump.</p><p>Low oil level.</p><p>Dirty oil cooler.</p><p>Restriction in cooler lines.</p><p>Remove, disassemble, and rebuild</p><p>convertor assembly.</p><p>Replace charging pump.</p><p>Fill to proper level.</p><p>Clean cooler.</p><p>Change cooler lines.</p><p>Noisy convertor. Worn charging pump.</p><p>Worn or damaged bearings.</p><p>Replace charging pump.</p><p>A complete disassembly will be</p><p>necessary to determine which</p><p>bearing is faulty.</p><p>Lack of power. Low engine RPM at convertor stall.</p><p>See Overheating and make same</p><p>checks.</p><p>Tune engine, check governor.</p><p>Make corrections as explained in</p><p>Overheating.</p><p>1300 SRM 1566 Troubleshooting</p><p>39</p><p>NOTES</p><p>40</p><p>TECHNICAL PUBLICATIONS</p><p>1300 SRM 1566 8/17 (7/14)(10/11)</p><p>Series Code / Model Designation Reference Table</p><p>General</p><p>Description of Operation</p><p>General</p><p>Operation</p><p>Hydraulic Operation</p><p>Anti-Drain</p><p>Cooling and Lubrication</p><p>Control System</p><p>General</p><p>APC Controller</p><p>Self Test</p><p>Protection Modes</p><p>Limp Home Mode</p><p>Shut Down Mode</p><p>Transmission Exceed Codes</p><p>Fault Codes Displayed on Instrument Cluster</p><p>Description</p><p>Fault Log Mode</p><p>Access</p><p>Exit</p><p>Clear</p><p>Fault Rectification</p><p>Transmission Control Valve</p><p>Pressure Check</p><p>Pressure Specifications</p><p>Pressure, Speed, and Temperature Sensors</p><p>Pressure Sensors</p><p>Test</p><p>Speed Sensor</p><p>Test</p><p>Temperature Sensors</p><p>Test</p><p>Transmission Test and Calibration</p><p>Precautions</p><p>Stall Test</p><p>Description</p><p>Stall Test Procedure</p><p>Clutch Filling Calibration</p><p>Description</p><p>Procedure</p><p>Inching Calibration</p><p>Description</p><p>Pedal and Sensor Adjustment for Braking and Inching for B/C917, G/H117 and C/D222.</p><p>Inching Pedal Sensor Adjustment</p><p>Pedal and Sensor Adjustment for Braking and Inching on A404</p><p>Inching Sensor Calibration</p><p>Electrical Specifications</p><p>Electrical Specifications</p><p>APC200 Display Information</p><p>General</p><p>General Information Group</p><p>Fault Codes</p><p>Indication of Protection Modes</p><p>Test Function Group</p><p>Digital Input Test</p><p>Analog Input Test</p><p>Speed Sensor Test</p><p>Output Test</p><p>Voltage Test</p><p>Calibration Group</p><p>Calibration Mode</p><p>Clutch Filling Calibration</p><p>Heat Up Mode</p><p>Inching Pedal Sensor Calibration</p><p>Inching Pedal Sensor Adjustment</p><p>Inching Pedal Sensor Calibration</p><p>Torque Specifications</p><p>Torque Specifications for Lubricated or Plated Screw Threads</p><p>Troubleshooting</p><p>Transmission Test and Calibration ......................................................................................................................18</p><p>Precautions ........................................................................................................................................................ 18</p><p>Stall Test ............................................................................................................................................................18</p><p>Description .....................................................................................................................................................18</p><p>Stall Test Procedure ...................................................................................................................................... 18</p><p>Clutch Filling Calibration .................................................................................................................................19</p><p>Description .....................................................................................................................................................19</p><p>Procedure ....................................................................................................................................................... 20</p><p>Inching Calibration ........................................................................................................................................... 20</p><p>Description .....................................................................................................................................................20</p><p>Pedal and Sensor Adjustment for Braking and Inching for B/C917, G/H117 and C/D222. ...................... 21</p><p>Inching Pedal Sensor Adjustment ................................................................................................................ 21</p><p>Pedal and Sensor Adjustment for Braking and Inching on A404 ...............................................................22</p><p>Inching Sensor Calibration ........................................................................................................................... 23</p><p>Electrical Specifications ........................................................................................................................................24</p><p>Electrical Specifications ....................................................................................................................................24</p><p>APC200 Display Information ................................................................................................................................24</p><p>General ...............................................................................................................................................................25</p><p>General Information Group .............................................................................................................................. 25</p><p>Table of Contents</p><p>i</p><p>TABLE OF CONTENTS (Continued)</p><p>Fault Codes ........................................................................................................................................................27</p><p>Indication of Protection Modes ......................................................................................................................... 27</p><p>Test Function Group ......................................................................................................................................... 27</p><p>Digital Input Test ..............................................................................................................................................29</p><p>Analog Input Test ..............................................................................................................................................30</p><p>Speed Sensor Test ............................................................................................................................................. 30</p><p>Output Test ........................................................................................................................................................31</p><p>Voltage Test ....................................................................................................................................................... 32</p><p>Calibration Group ..............................................................................................................................................34</p><p>Calibration Mode ........................................................................................................................................... 34</p><p>Clutch Filling Calibration .............................................................................................................................34</p><p>Heat Up Mode ................................................................................................................................................35</p><p>Inching Pedal Sensor Calibration .................................................................................................................35</p><p>Inching Pedal Sensor Adjustment ............................................................................................................ 35</p><p>Inching Pedal Sensor Calibration .............................................................................................................36</p><p>Torque Specifications ............................................................................................................................................ 36</p><p>Torque Specifications for Lubricated or Plated Screw Threads ..................................................................... 37</p><p>Troubleshooting .....................................................................................................................................................39</p><p>This section is for the following models:</p><p>Table of Contents</p><p>ii</p><p>Series Code / Model Designation Reference Table</p><p>This section is for the following models:</p><p>Series Code European Model Americas Model</p><p>A404 RS45-27CH, RS45-31CH RS45-27CH, RS45-31CH</p><p>B917 H36XMS-12, H40XM-12, H44XM-12,</p><p>H48XM-12 H800HD, H1050HD</p><p>C222</p><p>RS45-27CH, RS45-31CH, RS46-36CH,</p><p>RS46-41L CH, RS46-41S CH, RS46-41LS</p><p>CH, RS45-24 IH, RS45-28IH, RS46-33IH,</p><p>RS46-38L IH, RS46-38S IH, RS46-38LS IH</p><p>RS45-27, RS45-31, RS46-36, RS46-41L,</p><p>RS46-41S, RS46-41LS</p><p>C917</p><p>H40XM-12, H44XM-12, H48XM-12,</p><p>H36XMS-12, H40XMS-12, H44XMS-12,</p><p>H48XMS-12</p><p>H800HDS, H900HDS, H970HDS,</p><p>H1050HDS</p><p>D222</p><p>RS45-27CH, RS45-31CH, RS46-36CH,</p><p>RS46-41L CH, RS46-41S CH, RS46-41LS</p><p>CH, RS46-33IH, RS46-38L IH, RS46-38S</p><p>IH, RS46-38LS IH</p><p>RS45-27CH, RS45-31CH, RS46-36CH,</p><p>RS46-41L CH, RS46-41S CH, RS46-41LS</p><p>CH</p><p>G117 H40XM-16CH, H44XM-16CH, H48-16CH,</p><p>H50-16CH, H52XM-16CH H1050HD, H1150HD</p><p>H117 H40.00-52.00XM-16CH H1050HD-16CH, H1150HD-16CH</p><p>General</p><p>This manual provides information on the operation</p><p>and diagnostics of the TE-27 and TE-32</p><p>transmissions. The difference between models</p><p>TE-27 and TE-32 is in the torque converter and the</p><p>number of discs in the clutches. Model TE-27 is the</p><p>standard transmission for these truck series. Model</p><p>TE-32 is optionally available.</p><p>Truck series A404 uses transmission controller</p><p>APC312, which communicates through CANbus.</p><p>APC312 information can be read on the display of</p><p>the truck and through a PC. Other truck series</p><p>covered in this SRM use transmission controller</p><p>APC216, which shows information through an</p><p>integrated display and through a PC.</p><p>The repair procedures for the transmission and the</p><p>control valve are shown in Transmission Repair</p><p>1300SRM1445.</p><p>Electrical system diagrams are shown in:</p><p>• Diagrams 8000SRM2058 for A404.</p><p>• Diagrams 8000SRM1491 for C222.</p><p>• Diagrams 8000SRM1563 for B917 and G117.</p><p>• Diagrams 8000SRM1783 for C917.</p><p>• Diagrams 8000SRM1733 for D222.</p><p>• Diagrams 8000SRM1713 for H117.</p><p>1300 SRM 1566 Series Code / Model Designation Reference Table</p><p>1</p><p>Description of Operation</p><p>GENERAL</p><p>The transmission transfers engine power from the</p><p>engine flywheel to the drive</p><p>wheels, and to the</p><p>hydraulic pumps that are attached to the</p><p>transmission.</p><p>The engine flywheel is connected to the torque</p><p>converter through drive plates. See Figure 1.</p><p>The flexing properties of the drive plate reduce</p><p>transfer of axial forces between the engine</p><p>crankshaft and the torque converter. A gear on the</p><p>torque converter housing drives the transmission</p><p>pump and the attached pumps for the lift truck</p><p>hydraulic system. The torque converter housing,</p><p>transmission, and attached pumps turn at</p><p>proportional engine speed.</p><p>The oil pressure generated by the transmission</p><p>pump is used for lubrication, internal cooling, and</p><p>hydraulic control of the transmission. Without oil</p><p>pressure, the transmission cannot function.</p><p>The torque converter hydraulically connects the</p><p>engine flywheel to the transmission input shaft. The</p><p>torque converter functions as a torque multiplier,</p><p>and as a fluid clutch to smoothly transfer power</p><p>from the engine to the transmission. The heat</p><p>generated in this process is removed by the</p><p>transmission lubrication oil, which flows through</p><p>the torque converter.</p><p>The different speed ratios between the input shaft</p><p>and the drive shaft are obtained by engaging and</p><p>disengaging the different clutches. The engagement</p><p>and disengagement of the clutches is controlled by</p><p>the transmission control system.</p><p>Three groups of gears are continuously engaged</p><p>with each other: the input gears, the</p><p>interconnecting gears, and the output gears. See</p><p>Figure 2 and Figure 3.</p><p>1. DRIVE PLATE</p><p>2. TORQUE CONVERTER</p><p>3. PUMP DRIVE GEAR</p><p>4. INPUT GEAR</p><p>5. PUMP 1. SYSTEM PRESSURE</p><p>6. PUMP 2. LUBRICATION</p><p>7. CLUTCH FORWARD</p><p>8. TRANSMISSION INPUT SHAFT</p><p>Figure 1. Transmission Input Section</p><p>Description of Operation 1300 SRM 1566</p><p>2</p><p>If clutches belonging to one group would be engaged</p><p>simultaneously, the transmission would lock.</p><p>Erroneous clutch engagement is prevented by the</p><p>transmission control system.</p><p>Different speeds are obtained by engaging either the</p><p>forward or the reverse clutch, and by engaging the</p><p>1st, 2nd, 3rd or 4th speed clutch.</p><p>When the transmission is in NEUTRAL, the</p><p>forward clutch and the reverse clutch are</p><p>disengaged, while one of the speed clutches remains</p><p>engaged.</p><p>The clutches consist of a hub which carries friction</p><p>discs with internal splines, and a drum which</p><p>carries steel discs with external splines.</p><p>The friction discs and the steel discs are alternately</p><p>installed. By pressurizing the clutch piston, the</p><p>friction discs and the steel discs are clamped</p><p>together, which causes the hub and the drum to</p><p>rotate as one unit. When hydraulic pressure is</p><p>released, the return springs force the piston back</p><p>against the clutch housing and allows the hub and</p><p>drum to rotate independently. The drum, steel discs,</p><p>piston, spacer, and return springs rotate at the</p><p>same speed. The hub and friction discs rotate at the</p><p>same speed. See Figure 4.</p><p>A. INPUT GEARS</p><p>B. INTERCONNECTING GEARS</p><p>C. OUTPUT GEARS</p><p>Figure 2. Gear Engagement</p><p>1300 SRM 1566 Description of Operation</p><p>3</p><p>1. INPUT GEARS</p><p>2. INTERCONNECTING GEARS</p><p>3. OUTPUT GEARS</p><p>Figure 3. Gear Engagement</p><p>1. CLUTCH PRESSURE OIL SUPPLY</p><p>2. LUBRICATION OIL SUPPLY</p><p>3. SHAFT SEALS</p><p>4. INTERCONNECTING GEAR</p><p>5. CLUTCH HUB</p><p>6. CLUTCH DRUM</p><p>7. PISTON SEALS</p><p>8. OUTPUT GEAR</p><p>9. PISTON SPRINGS</p><p>10. WEAR SLEEVE</p><p>11. PISTON</p><p>12. CLUTCH PLATES</p><p>13. CLUTCH END PLATE</p><p>Figure 4. Clutch Components</p><p>Operation</p><p>HYDRAULIC OPERATION</p><p>The transmission sump is the main reservoir for</p><p>transmission oil. The transmission pumps are</p><p>driven by gears that connect with the torque</p><p>converter housing. The pumps transfer the oil from</p><p>the sump to the remote transmission filters. Each</p><p>filter has a bypass valve that opens when pressure</p><p>difference between filter entry and filter outlet</p><p>exceeds 0.45 MPa (65.2 psi).</p><p>The smaller pump (pump 2) provides oil for</p><p>lubrication and internal cooling only.</p><p>The bigger pump (pump 1) provides oil to the</p><p>22 bar (319 psi) pressure regulator valve, which</p><p>relieves excess oil through the torque converter, oil</p><p>cooler and lubrication system. To protect the torque</p><p>converter and cooling system, a safety valve opens</p><p>when pressure exceeds 9 bar (131 psi). See</p><p>Cooling and Lubrication.</p><p>The regulated system pressure of 22 bar (319 psi) is</p><p>used to fill and pressurize the clutches. Pressure is</p><p>admitted to the clutches through proportional</p><p>valves and selector valves, which receive electrical</p><p>signals from the APC controller.</p><p>The proportional valves admit and release oil</p><p>pressure according a varying signal from the APC</p><p>controller. This varying signal allows a controlled</p><p>engagement and release of the clutches. To dampen</p><p>hydraulic vibration, a dampening spool is connected</p><p>with the supply channel for each proportional valve.</p><p>In the supply channels for the speed clutches</p><p>(1st/3rd and 2nd/4th gear) the actual clutch</p><p>pressure is measured by a sensor.</p><p>Operation 1300 SRM 1566</p><p>4</p><p>The APC controller uses this pressure signal and</p><p>the speed sensor signals to control engagement and</p><p>release of the different clutches during shifting.</p><p>If the APC controller does NOT receive the proper</p><p>signals, then all proportional valves will be</p><p>deactivated, causing all clutches to release</p><p>immediately.</p><p>The selector valves receive an ON or OFF signal to</p><p>divert pressure to the correct clutch.</p><p>The 1st/3rd selector valve diverts pressure to 1st</p><p>gear clutch when activated and to 3rd gear clutch</p><p>when not activated.</p><p>The 2nd/4th selector valve diverts pressure to 2nd</p><p>gear clutch when activated and to 4th gear clutch</p><p>when not activated.</p><p>The forward/reverse selector valve requires a</p><p>specific forward or reverse signal to divert pressure</p><p>to the relevant clutch. Neutral selection is by</p><p>deactivating both the forward and reverse signal.</p><p>The APC controller selects neutral by each of the</p><p>following inputs:</p><p>• Neutral position of the gear shift selector</p><p>• Park brake engagement</p><p>• Fully depressed inching pedal</p><p>• Seat NOT occupied</p><p>• Sensor inputs causing the APC controller to</p><p>engage neutral.</p><p>For an overview of the activated solenoids and</p><p>clutches for the different transmission speeds See</p><p>Table 1.</p><p>NOTE: When Neutral is selected the speed clutches</p><p>will remain engaged according the position of the</p><p>gear shift lever or according the gear selected by the</p><p>automatic drive system.</p><p>NOTE: The transmission will automatically shift to</p><p>neutral a few seconds after the operator has left the</p><p>seat.</p><p>ANTI-DRAIN</p><p>To allow normal clutch re-pressurization, the</p><p>system supply channels must remain filled with oil.</p><p>To prevent that the supply channels would drain</p><p>and fill with air, some of the system oil is</p><p>continuously fed into the drain channel through a</p><p>restriction hole. See Figure 5.</p><p>Table 1. Gear Selection and Activated Solenoids</p><p>Selected Gear Activated Proportional</p><p>Valve</p><p>Activated Selector</p><p>Valve Activated Clutches</p><p>Forward 1 FWD/REV + 1st/3rd FWD + 1st/3rd FWD + 1st</p><p>Forward 2 FWD/REV + 2nd/4th FWD + 2nd/4th FWD + 2nd</p><p>Forward 3 FWD/REV + 1st/3rd FWD FWD + 3rd</p><p>Forward 4 FWD/REV + 2nd/4th FWD FWD + 4th</p><p>Reverse 1 FWD/REV + 1st/3rd REV + 1st/3rd REV + 2nd/4th</p><p>Reverse 2 FWD/REV + 2nd/4th REV + 2nd/4th REV + 2nd</p><p>Reverse 3 FWD/REV + 1st/3rd REV REV + 3rd</p><p>Reverse 4 FWD/REV + 2nd/4th REV REV + 4th</p><p>1300 SRM 1566 Operation</p><p>5</p><p>Figure 5. Hydraulic Diagram</p><p>Operation 1300 SRM 1566</p><p>6</p><p>COOLING AND LUBRICATION</p><p>Heat is primarily generated at the torque converter</p><p>and at the clutch plates during transmission</p><p>operation. The heat generated by mechanical</p><p>friction at gears, shafts and bearings is relatively</p><p>low.</p><p>Heat generated in the torque converter relates</p><p>directly to the degree of stall, i.e. the speed</p><p>difference between engine and turbine. In a stall</p><p>situation most of the supplied engine power is</p><p>transferred into heat. This heat accumulates in the</p><p>torque converter because of the reduced oil flow</p><p>during a stall situation. With increasing turbine</p><p>speed, the volume of added heat reduces, while</p><p>simultaneously the increased oil flow more rapidly</p><p>transfers the accumulated heat.</p><p>Heat generated at the clutch plates varies with the</p><p>actually available engine power at time of clutch</p><p>engagement and the duration of clutch</p><p>engagement.</p><p>During normal operation, the transmission control</p><p>system determines the duration of clutch</p><p>engagement. During inching it is the driver who</p><p>controls the added heat in the clutch by varying</p><p>engine power and clutch engagement. The</p><p>transmission control system will close the forward</p><p>or reverse clutch when a certain amount of</p><p>generated heat has been exceeded.</p><p>Only a minor portion of pump oil supply is used for</p><p>clutch filling. The majority of transmission oil</p><p>supply is used for the cooling and lubrication circuit</p><p>that functions at a pressure that is lower than</p><p>system pressure. See Figure 5, Hydraulic Diagram.</p><p>The smaller transmission pump directly provides oil</p><p>to the lubrication circuit through the oil filter. See</p><p>Figure 6.</p><p>The bigger transmission pump provides oil to the</p><p>lubrication circuit through the torque converter and</p><p>transmission oil cooler. The pressure regulator</p><p>valve admits oil that is not required for clutch</p><p>filling. The safety valve reduces oil pressure to</p><p>9 bar (130.5 psi) to protect the torque converter and</p><p>oil cooler.</p><p>With increasing stall of the torque converter, flow</p><p>resistance increases, causing a reduced oil flow</p><p>through the torque converter and causing the</p><p>9 bar (130.5 psi) safety valve to relieve more oil. In a</p><p>stall situation most of the lubrication oil is provided</p><p>by the smaller transmission pump.</p><p>From the transmission lubrication port the oil flows</p><p>into channels in the different shafts, which lead to</p><p>the shaft bearings for lubrication, and to the inside</p><p>of the clutch packs where the oil absorbs the heat</p><p>that is generated at the clutch plates.</p><p>To speed the warming-up process, a thermostat</p><p>valve is installed between the torque converter</p><p>outlet port and the transmission radiator. The</p><p>thermostat starts opening at 87°C (188.6°F) and is</p><p>completely opened at 102°C (188.6°F). At</p><p>temperatures below 87°C (215.6°F), oil flow is</p><p>directly returned to the transmission. At</p><p>temperatures above 102°C (215.6°F), the entire oil</p><p>flow from the outlet port passes through the</p><p>transmission radiator before it is returned to the</p><p>transmission.</p><p>1. FILTER</p><p>2. OIL COOLER</p><p>3. THERMOSTAT VALVE</p><p>Figure 6. Port Connections Cooling and Filtration</p><p>1300 SRM 1566 Operation</p><p>7</p><p>Control System</p><p>GENERAL</p><p>The controller system of the transmission consists of</p><p>the APC216 or APC312 controller, several switches</p><p>and sensors, and the hydraulic control valve. The</p><p>sensors and switches provide information to the</p><p>APC controller, which sends signals to the control</p><p>valve to operate the solenoids</p><p>APC CONTROLLER</p><p>The APC controller has software that controls the</p><p>operation of the transmission and performs the</p><p>following functions:</p><p>• Self-testing and troubleshooting.</p><p>• Functional control of the transmission.</p><p>- Automatic shifting gear selection.</p><p>- Inching.</p><p>• Entering a protection mode when required:</p><p>- Improper pressures, temperatures, and</p><p>speeds.</p><p>- No operator present.</p><p>- Parking brake applied.</p><p>- Gear or direction change at improper</p><p>speeds.</p><p>• Logging a fault code when circumstances</p><p>have exceeded certain values.</p><p>• Allowing diagnostics and calibration with a</p><p>laptop (Dana Dashboard software).</p><p>Depending on the signals of the shift lever and</p><p>various switches and sensors, the APC controller</p><p>activates or deactivates the solenoids and VFS in</p><p>the control valve, which transfer hydraulic oil</p><p>pressure to the clutches in the transmission. If an</p><p>input signal does not comply with the programming</p><p>of the APC, the APC controller will record the fault</p><p>and react by activating a protection mode. All</p><p>recorded events are stored as fault codes and are</p><p>shown on the hourmeter/fault code display when the</p><p>fault occurs. Faults can also be retrieved and read</p><p>at a later time, making it possible to trace</p><p>intermittent problems.</p><p>Protection modes and self tests are part of the APC</p><p>controller programming and cannot be influenced.</p><p>The APC312 controller for A404 is located in the</p><p>battery box. For diagnostics and settings use the</p><p>Dana Dashboard software system.</p><p>The APC216 controller is located in the side console</p><p>of the cab and has a display and push buttons to call</p><p>off information. Normally, the gauges and displays</p><p>on the instrument panel are used to read</p><p>transmission-related information. For diagnostics</p><p>and settings, it is recommended to use the Dana</p><p>Dashboard software system. Refer to</p><p>APC200 Display Information for the instructions on</p><p>how to access and retrieve information from the</p><p>APC216 controller when the Dana Dashboard</p><p>software is not available.</p><p>Self Test</p><p>A series of checks is done at power-up. If the APC</p><p>controller fails these checks, it will shut off all</p><p>outputs. The transmission cannot be operated until</p><p>the problem is resolved or repaired. A fault code will</p><p>be displayed.</p><p>Protection Modes</p><p>Limp Home Mode</p><p>The transmission shifts to NEUTRAL if a fault is</p><p>detected on the following:</p><p>• Outputs for solenoids, VFS, or pressure</p><p>switch</p><p>• Engine speed sensor</p><p>• Two out of three transmission speed sensors</p><p>(turbine, drum, or output speed sensor).</p><p>To continue driving, place the shift lever in</p><p>NEUTRAL, and reengage a direction. When Limp</p><p>Home Mode has been entered, the user can operate</p><p>the transmission in either direction in 1st and 2nd</p><p>gear only, and inching is disabled.</p><p>Shut Down Mode</p><p>If an intolerable combination of faults is detected,</p><p>the Shut Down Mode will be entered. The APC216</p><p>controller puts the transmission in NEUTRAL by</p><p>putting all VFS signals at zero pressure and by</p><p>switching OFF the total neutral solenoid, cutting off</p><p>pressure to the clutches. Intolerable faults are also</p><p>referred to as Redundant Shutdown Path (RSP)</p><p>errors.</p><p>Transmission Exceed Codes</p><p>During operation of the lift truck, the APC</p><p>controller may display transmission exceed codes on</p><p>Control System 1300 SRM 1566</p><p>8</p><p>the hourmeter/fault code display. These exceed</p><p>codes show that the request made by the operator</p><p>will not be executed because of certain</p><p>circumstances. APC200 Fault Code Guide</p><p>1300SRM1435 or SPN / FMI Code Guide</p><p>9000SRM2046 lists the transmission exceed codes</p><p>with a description of the encountered</p><p>circumstances. In addition, truck series A404</p><p>explains most of the exceed codes on the Display.</p><p>Fault Codes Displayed on Instrument</p><p>Cluster</p><p>Description</p><p>Under normal conditions, the hour meter/fault code</p><p>display on the instrument cluster shows engine</p><p>running hours. The maximum hours that can be</p><p>displayed is 9999.9 hours.</p><p>• Hourmeter reading</p><p>If the engine and/or transmission controller detects</p><p>a fault, the hourmeter/fault code display will show a</p><p>fault code instead of the engine running hours.</p><p>Fault codes starting with E’ refer to engine fault</p><p>codes.</p><p>• Fault code number(s)</p><p>Fault codes starting with t’ refer to transmission</p><p>exceed and fault codes, which are listed in APC200</p><p>Fault Code Guide 1300SRM1435 or SPN / FMI</p><p>Code Guide 9000SRM2046.</p><p>When more than one fault occurs at the same time,</p><p>the fault codes will be displayed in succession.</p><p>When circumstances have changed and all faults</p><p>have ceased to exist, the hour meter/fault code</p><p>display will show engine running hours again.</p><p>Fault code E-CON and t-CON indicate a</p><p>communication problem.</p><p>Display fault code E-CON is shown when the</p><p>following occurs:</p><p>• The engine controller does not reply to the</p><p>engine identification request or request for</p><p>fault codes.</p><p>• The engine controller stops sending one of the</p><p>regular messages, such as engine RPM or</p><p>engine coolant temperature.</p><p>Display fault code t-CON is shown when the</p><p>instrument cluster does not receive a cyclic message</p><p>or receives incorrect error messages from the</p><p>APC216 controller.</p><p>Fault codes that appear as tE123 are for faults that</p><p>occur during calibration of the transmission.</p><p>Fault Log Mode</p><p>Access</p><p>The instrument cluster has a memory that records</p><p>each fault as it occurs. The faults that have occurred</p><p>can be reviewed at a later point in time by entering</p><p>into the fault log mode. Proceed as follows to enter</p><p>into the fault log mode:</p><p>1. Apply the parking brake.</p><p>2. Turn the key switch to ON, but do not start the</p><p>lift truck.</p><p>3. Turn the key switch OFF and ON three times,</p><p>switching one time</p><p>per second. After the first</p><p>OFF and ON cycle, the display will show a 1’.</p><p>After the second OFF and ON cycle, the</p><p>display will show a 2’. After the third OFF and</p><p>ON cycle, the display will show a 3’.</p><p>The display is now in fault log mode. When no faults</p><p>have been recorded, the LCD display shows clear’.</p><p>When faults have been recorded, the display shows</p><p>a letter and four numbers for each fault code. For</p><p>engine fault codes, the letter is E’. For transmission</p><p>fault codes, the letter is t’.</p><p>After the fault code, three numbers are shown</p><p>which represent the following:</p><p>• Fault code</p><p>• Hourmeter reading at last occurrence</p><p>• Hourmeter reading at first occurrence</p><p>• Number of occurrences of current fault</p><p>Each number is shown for three seconds, after</p><p>which the following number is shown. The faults</p><p>will be shown in the opposite sequence of</p><p>occurrence: the most recent fault first and the initial</p><p>fault last. When all recorded fault codes have been</p><p>shown, the display will continue to repeat the</p><p>recorded fault codes until the user exits the fault log</p><p>mode.</p><p>1300 SRM 1566 Control System</p><p>9</p><p>Exit</p><p>To exit the fault log mode, turn the key switch OFF</p><p>and then ON, leaving the key switch ON for more</p><p>than two seconds. The cluster will also exit to</p><p>normal mode when the parking brake is released or</p><p>when the engine is started.</p><p>Clear</p><p>To clear the fault codes logged in the display,</p><p>proceed as follows:</p><p>1. Access the fault log mode. See Access.</p><p>2. Clear the fault log by cycling the ignition key</p><p>OFF and ON three more times. This is a</p><p>repetition of the procedure to access the fault</p><p>log mode. See Access.</p><p>If the data-erasing process is successful, the display</p><p>will show 'clear'. If the data-erasing process is not</p><p>successful, the display will show the fault codes in</p><p>the memory, shown in the order by the time of the</p><p>occurrence. To return to the normal mode, follow the</p><p>procedure as described in Exit. To retry erasing</p><p>stored fault codes, follow Step 2 of the procedure to</p><p>clear fault codes.</p><p>Fault Rectification</p><p>Fault codes are listed in APC200 Fault Code</p><p>Guide 1300SRM1435 or SPN / FMI Code Guide</p><p>9000SRM2046, which provides an explanation of</p><p>the fault, the resulting action of the APC controller,</p><p>and checks for troubleshooting. Each fault code</p><p>represents a specific defect or malfunction.</p><p>In most cases, the suggested solution is to check</p><p>electrical functionality between the APC controller,</p><p>the wiring and sensors, solenoids, or switches.</p><p>Before disassembling components for test purposes,</p><p>connect the Dana Dashboard software. The screen</p><p>Dashboard-Monitor’ allows verification of the</p><p>functionality of speed sensors, the pressure switch,</p><p>and the shift lever. If several possible defects are</p><p>indicated, Dana Dashboard software may narrow</p><p>down the number of possible defects, preventing</p><p>unnecessary removal of components that function</p><p>correctly.</p><p>To repair problems with switches, solenoids, and</p><p>sensors, look up their actual location, and test the</p><p>component. The location of the solenoids are shown</p><p>in the section Transmission Control Valve. The</p><p>location of sensors and switches are shown in the</p><p>section Pressure, Speed, and Temperature Sensors.</p><p>Test values of solenoids and sensors are shown in</p><p>Electrical Specifications.</p><p>Note that the Dana Dashboard software and the</p><p>APC200 Fault Code Guide 1300SRM1435 or</p><p>SPN / FMI Code Guide 9000SRM2046 have wire</p><p>references and input references that relate to the</p><p>APC controller.</p><p>Refer to Table 11 for the conversion from APC</p><p>controller wire numbers to Hyster wire numbers.</p><p>To determine the exact location of a harness</p><p>problem, refer to electrical system diagrams shown</p><p>in:</p><p>• Diagrams 8000SRM2058 for A404.</p><p>• Diagrams 8000SRM1491 for C222.</p><p>• Diagrams 8000SRM1563 for B917 and G117.</p><p>• Diagrams 8000SRM1783 for C917.</p><p>• Diagrams 8000SRM1733 for D222.</p><p>• Diagrams 8000SRM1713 for H117.</p><p>TRANSMISSION CONTROL VALVE</p><p>The hydraulic control valve is located at the right-</p><p>hand side of the transmission and contains the</p><p>pressure switch, all solenoids, most of the valves</p><p>and several check ports. Functioning of the</p><p>hydraulic control valve depends on available pump</p><p>supply pressure and the activation of the electrical</p><p>solenoids. Activation of these solenoids is controlled</p><p>by the APC controller. Hydraulic functioning of the</p><p>control valve is schematically shown on the</p><p>hydraulic diagram on Figure 6.</p><p>The numbers in circles refer to check port numbers.</p><p>Table 2 lists the check port numbers, description,</p><p>figure and item number that show the location of</p><p>these ports</p><p>The location of the solenoids and the pressure</p><p>switch is shown in Figure 7.</p><p>Control System 1300 SRM 1566</p><p>10</p><p>Table 2. Port Numbers</p><p>Port Number Port Description Pressure Figure Item</p><p>Port 31 System Pressure</p><p>22.5 bar (326 psi)minimum @</p><p>600 rpm25.5 bar (370 psi)</p><p>maximum @ governed speed</p><p>See Figure 10 1</p><p>Port 31A System Pressure System Pressure See Figure 8 1</p><p>Port 32 Torque Converter</p><p>Out</p><p>5 bar (73 psi)minimum @ 2000</p><p>rpm8.5 bar (123 psi) maximum @</p><p>governed speed</p><p>See Figure 11 11</p><p>Port 34 Lubrication Supply</p><p>5 bar (58 psi)minimum @ 2000</p><p>rpm7.5 bar (109 psi) maximum @</p><p>governed speed</p><p>See Figure 11 9</p><p>Port 37 Torque Converter</p><p>In/Safety Valve</p><p>4 bar (128 to 139 psi) Cracking</p><p>Pressure See Figure 10 10</p><p>Port 41 Clutch 1st Pressure 20.5 bar (397 psi) minimum @</p><p>2200 rpm See Figure 8 6</p><p>Port 42 Clutch 2nd Pressure 20.5 bar (397 psi)minimum @</p><p>2200 rpm See Figure 11 1</p><p>Port 43 Clutch 3rd Pressure 20.5 bar (397 psi)minimum @</p><p>2200 rpm See Figure 11 17</p><p>Port 44 Clutch 4th Pressure 20.5 bar (397 psi)minimum @</p><p>2200 rpm See Figure 11 3</p><p>Port 45 Clutch Forward</p><p>Pressure</p><p>20.5 bar (397 psi)minimum @</p><p>2200 rpm See Figure 10 4</p><p>Port 46 Clutch Reverse</p><p>Pressure</p><p>20.5 bar (397 psi)minimum @</p><p>2200 rpm See Figure 11 2</p><p>Port 66 FWD/REV</p><p>Regulated Valve System Pressure See Figure 8 10</p><p>Port 67 3rd/1st Regulated</p><p>Valve System Pressure See Figure 8 7</p><p>Port 68 2nd/4th Regulated</p><p>Valve System Pressure See Figure 8 8</p><p>1300 SRM 1566 Control System</p><p>11</p><p>Figure 7. Solenoid Locations</p><p>Item C222, G117, B917 D222, H117,</p><p>C917 A404 Description</p><p>1 CPS140 CPS124 CPS067 FWD Selector Solenoid</p><p>2 CSP130 CPS122 CPS065 REV Selector Solenoid</p><p>3 CPS150 CPS088 CPS093 FWD/REV Proportional</p><p>Solenoid</p><p>4 CPS160 CPS072 CPS072 2nd/4th Proportional</p><p>Solenoid</p><p>5 CPS170 CPS123 CPS066 1st/3rd Proportional</p><p>Solenoid</p><p>6 CPS190 CPS149 CPS094 2nd/4th Selector Valve</p><p>7 CPS200 CPS008 CPS005 2nd/4th Pressure Sensor</p><p>8 CPS210 CPS004 CPS009 1st/3rd Pressure Sensor</p><p>9 CPS180 CPS121 CPS064 1st/3rd Selector Valve</p><p>Control System 1300 SRM 1566</p><p>12</p><p>Pressure Check</p><p>Check ports for transmission oil pressures are at</p><p>different locations on the outside of the</p><p>transmission housing and on the control valve. See</p><p>Figure 8, Figure 10, and Figure 11. An overview of</p><p>port numbers, pressure specifications and port</p><p>locations is in Table 2.</p><p>Most of the transmission oil pressures can be</p><p>measured at the side of the control valve. See</p><p>Figure 8 and Table 2 that lists the check port</p><p>numbers and their description. Further check points</p><p>for transmission oil pressures are at different</p><p>locations on the transmission. See Figure 10 and</p><p>Figure 11.</p><p>The port numbers mentioned at each check point</p><p>correspond with the port numbers as shown on the</p><p>Figure 5.</p><p>None of the oil pressures are adjustable. If a</p><p>pressure is out of specification, the cause has to be</p><p>established by further checking before replacing the</p><p>pressure valves. The transmission housing includes</p><p>the pressure regulating valve and the safety valve.</p><p>The filter bypass valves are included in the filter</p><p>cartridges.</p><p>With the transmission control valve removed, oil</p><p>ports leading to the various clutches can be</p><p>pressurized with air. The amount of air pressure</p><p>applied should be approximately 14 bar (203 psi).</p><p>When applying air pressure to the control valve</p><p>ports, clutch engagement and obvious leaks can be</p><p>established. For the location of the ports see</p><p>Figure 9.</p><p>Item</p><p>Number</p><p>Port</p><p>Number Description</p><p>1 31a System Pressure</p><p>2 45 FWD Clutch Pressure</p><p>3 43 3rd Clutch Pressure</p><p>4 44 4th Clutch Pressure</p><p>5 42 2nd Clutch Pressure</p><p>6 41 1st Clutch Pressure</p><p>7 67 1st/3rd</p><p>Regulated Pressure</p><p>8 68 2nd/4th Regulated Pressure</p><p>9 46 REV Clutch Pressure</p><p>10 66 FWD/REV Regulated</p><p>Pressure</p><p>Figure 8. Check Ports, Control Valve</p><p>1300 SRM 1566 Control System</p><p>13</p><p>A. TOP</p><p>1. REGULATOR</p><p>2. 4TH CLUTCH</p><p>3. 1ST CLUTCH</p><p>4. REVERSE CLUTCH</p><p>5. 2ND GEAR</p><p>6. 3RD GEAR CLUTCH</p><p>7. FORWARD CLUTCH</p><p>Figure 9. Transmission Control Valve Ports</p><p>PRESSURE SPECIFICATIONS</p><p>The relief pressures in this transmission are</p><p>influenced by the volume and viscosity of the oil</p><p>passing through the relief valves. Smaller supply</p><p>volumes and lower viscosity result in lower system</p><p>pressures. Bigger supply volumes and higher</p><p>viscosity result in higher system pressures. The</p><p>volume of oil through the relief valves depends on</p><p>engine speed. Viscosity depends on oil quality and</p><p>decreases with higher temperatures. Make sure</p><p>that oil quality meets the required specification and</p><p>that oil has been replaced in time. Temperature of</p><p>the oil must be 82 to 93°C (180 to 199°F) for correct</p><p>pressure measurement.</p><p>An overview of the normal pressures at the various</p><p>check ports is in Table 2.</p><p>In the cooling and lubrication circuit the torque</p><p>converter causes additional flow resistance with</p><p>increasing speed difference between engine and</p><p>transmission input shaft.</p><p>When insufficient flow of cooling oil is suspected,</p><p>compare the pressures at port 34 and port 32 both</p><p>in a condition of torque converter stall and running</p><p>in neutral.</p><p>PRESSURE, SPEED, AND TEMPERATURE</p><p>SENSORS</p><p>Before disassembling components for test purposes,</p><p>connect the Dana Dashboard software. The screen</p><p>Dashboard-Monitor’ allows verification of the</p><p>functionality of several components, preventing</p><p>unnecessary removal of components that function</p><p>correctly.</p><p>The location of the speed and temperature sensors</p><p>are shown in Figure 10. The engine speed sensor is</p><p>located at the pump drive gear. The schematic</p><p>location of the turbine, output, and drum speed</p><p>sensors is shown in Figure 12.</p><p>1. SYSTEM PRESSURE</p><p>2. TO COOLER</p><p>3. ENGINE SPEED SENSOR</p><p>4. PORT 45 - FWD CLUTCH</p><p>5. FROM COOLER</p><p>6. FROM REMOTE FILTER</p><p>7. TURBINE SPEED SENSOR</p><p>8. OUTPUT SPEED SENSOR</p><p>9. DRUM SPEED SENSOR</p><p>10. PORT 37 - CONVERTER IN</p><p>Figure 10. Check Ports and Senders, Right Side</p><p>View</p><p>Control System 1300 SRM 1566</p><p>14</p><p>Figure 11. Check Ports, Front and Rear View</p><p>Legend for Figure 11.</p><p>A. FRONT VIEW</p><p>B. REAR VIEW</p><p>1. PORT 42 - CLUTCH 2ND</p><p>2. PORT 46 - CLUTCH REVERSE</p><p>3. PORT 44 - CLUTCH 4TH</p><p>4. PLUG, DRAIN</p><p>5. ENGINE SPEED SENSOR</p><p>6. DRUM SPEED SENSOR</p><p>7. OUTPUT SPEED SENSOR</p><p>8. TURBINE SPEED SENSOR</p><p>9. PORT 34 - LUBRICATION SUPPLY</p><p>10. FROM FILTER 1</p><p>11. PORT 32 - TORQUE CONVERTER OUT</p><p>12. TEMPERATURE SWITCH</p><p>13. ENGINE SPEED SENSOR</p><p>14. TEMPERATURE SENSOR</p><p>15. DRUM SPEED SENSOR</p><p>16. OUTPUT SPEED SENSOR</p><p>17. PORT 43 - CLUTCH 3RD</p><p>Pressure Sensors</p><p>The function of the pressure sensors is to monitor</p><p>pressure overlap on range clutches during shifting.</p><p>Test</p><p>When system pressure is applied, the internal</p><p>resistance of the pressure sensor is about 500 Ohm.</p><p>The APC controller signals a fault when the</p><p>resistance is incorrect for the given circumstances.</p><p>Te-Userlink shows the measured resistance value</p><p>under Pressure Switch Resistance’. The location of</p><p>the pressure switches is shown on</p><p>Figure 7, Solenoid Locations.</p><p>Maximum current is 10 mA at a supply voltage</p><p>between 4.5 and 5.5 Volt and applied pressure of</p><p>20 bar (290 psi).</p><p>Speed Sensor</p><p>The speed sensors determine the rotation speed of</p><p>the different gear groups. The APC controller</p><p>calculates the speed ratios between the different</p><p>groups and compares the calculated values with the</p><p>programmed values. If deviation exceeds an</p><p>allowable value, the APC controller generates a</p><p>fault code and eventually enters a protection mode.</p><p>See Figure 12. The following are a few examples of</p><p>speed inputs and ratios that are monitored by the</p><p>APC controller:</p><p>• Converter Speed Ratio</p><p>1300 SRM 1566 Control System</p><p>15</p><p>- The ratio between engine speed and</p><p>turbine speed is called the converter</p><p>speed ratio. The converter speed ratio is</p><p>a measure of the power being transferred</p><p>through the converter. This ratio is a</p><p>major factor for the APC controller to</p><p>determine if a higher or lower gear is to</p><p>be selected during the automatic</p><p>selection mode. During calibration, a</p><p>sudden change in converter speed ratio is</p><p>used to determine the clutch piston</p><p>position at the moment the clutch starts</p><p>clamping.</p><p>• Transmission Ratio</p><p>- Each selected transmission gear has a</p><p>specific transmission ratio. When one of</p><p>the direction clutches is closed and the</p><p>output speed has reached a certain value</p><p>for checking, the actual ratio is compared</p><p>with the specified ratio. If deviation</p><p>exceeds 5%, one of the clutches is</p><p>assumed to be slipping. A fault is flagged</p><p>and the APC controller enters the Shut</p><p>Down Mode.</p><p>• Gear Ratio</p><p>- If the turbine, drum, or output speed</p><p>sensor fails, the APC controller</p><p>calculates the actual ratio’ based on the</p><p>value of the remaining sensors. This</p><p>allows continued operation of the</p><p>transmission. Speed sensor failure is</p><p>indicated by a fault code. If the engine</p><p>speed sensor fails, or if more than one</p><p>speed sensor fails, the APC controller</p><p>will enter the Limp Home Mode and flag</p><p>a fault.</p><p>• Maximum Torque During Inching</p><p>- The APC programming interprets the</p><p>inching pedal position as the required</p><p>pressure for the inching clutch. The heat</p><p>generated in the inching clutch is</p><p>proportional to the power transferred by</p><p>the torque converter (converter speed</p><p>ratio). When the power is transferred at</p><p>an excessively high level for an extended</p><p>period of time, the APC controller will</p><p>release pressure in the clutch and flag a</p><p>fault.</p><p>A. TURBINE SPEED</p><p>B. DRUM SPEED</p><p>C. OUTPUT SPEED</p><p>Figure 12. Schematic Speed Sensor Locations</p><p>Control System 1300 SRM 1566</p><p>16</p><p>Test</p><p>Dana Dashboard software shows functionality of</p><p>each of the speed sensors under Speed Monitor’.</p><p>Electrical functionality can be tested by using the</p><p>schematic shown in Figure 13. Observe the correct</p><p>sensor polarity. Pin 1 must be connected to 12 Volt</p><p>+. Pin 2 must be connected to 12 Volt-. For the</p><p>engine speed sensor, pin A must be connected to 12</p><p>Volt+. Pin C must be connected to 12 Volt-.</p><p>Figure 13 shows the connectors which are used to</p><p>connect to the speed sensors. Connecting the sensor</p><p>with an incorrect polarity will destroy the sensor.</p><p>Table 3 shows the acceptable test values. Replace</p><p>the sensor if it fails the test.</p><p>Speed sensors should be installed as close as</p><p>possible to the gear. The speed signal will fail if the</p><p>distance exceeds 1.8 mm (0.07 in.). The sensor</p><p>mounting bracket normally ensures correct sensor</p><p>installation.</p><p>Table 3. Speed Sensor Test Values</p><p>Voltage</p><p>Reading</p><p>Current</p><p>Level</p><p>Gear tooth sensed 1.2 volt 6 to 8 mA</p><p>No gear tooth</p><p>sensed 2.6 to 3.0 volt 13 to 15 mA</p><p>Figure 13. Speed Sensor Test</p><p>1300 SRM 1566 Control System</p><p>17</p><p>Temperature Sensors</p><p>There are two temperature sensors which measure</p><p>the temperature at two different locations:</p><p>• Pump Supply</p><p>- This temperature sensor is combined</p><p>with the engine speed sensor in one unit</p><p>and is connected with the APC controller</p><p>through pin B of the sensor connector.</p><p>The temperature measured is from the</p><p>oil returning from filter 1, close to port</p><p>31. The signal to the APC controller is</p><p>translated into a CANbus signal to the</p><p>instrument cluster and represents the</p><p>transmission sump temperature. Dana</p><p>Dashboard software indicates</p><p>functionality of this temperature sensor</p><p>under Transmission sump temperature.’</p><p>• Torque Converter Out, Port 32</p><p>- This temperature sensor is a switch that</p><p>connects to ground when the</p><p>temperature has exceeded 120°C (248°F).</p><p>The function of this temperature switch</p><p>is to trigger a protection mode.</p><p>Functionality can only be tested by</p><p>immersing the temperature switch in hot</p><p>oil, and measuring if it switches at</p><p>120°C (248°F).</p><p>Test</p><p>Table 4 shows the electrical resistance values of the</p><p>sump temperature sensor for different</p><p>temperatures. Resistance can be measured with a</p><p>normal ohmmeter, if correct polarity is observed.</p><p>Transmission Test and Calibration</p><p>PRECAUTIONS</p><p>Before testing or calibrating the transmission,</p><p>verify</p><p>the following:</p><p>• Check the engine coolant level. Add coolant as</p><p>needed.</p><p>• Make sure the parking brake and service</p><p>brakes operate correctly.</p><p>• Check the transmission fluid level. Add</p><p>transmission fluid as needed.</p><p>• Make sure the transmission oil temperature</p><p>is at least 60°C (140°F).</p><p>Refer to the Operating Manual for instructions on</p><p>how to add coolant and transmission oil.</p><p>To raise the oil temperature, run the engine while</p><p>stalling the torque converter as follows:</p><p>1. Place the lift truck against an object that</p><p>cannot move.</p><p>2. Apply the brake pedal and release the parking</p><p>brake.</p><p>3. Select the 3rd range position on the</p><p>transmission shift lever.</p><p>4. Run the engine at half throttle until the</p><p>transmission oil temperature gauge indicates</p><p>60°C (140°F).</p><p>NOTE: The transmission will shift to NEUTRAL</p><p>when the parking brake is applied.</p><p>STALL TEST</p><p>Description</p><p>The stall test provides indications for the condition</p><p>of the engine, transmission clutches, and torque</p><p>converter. The stall test is performed with the</p><p>transmission engaged and the engine operating at</p><p>full throttle, while the drive wheels are being</p><p>blocked. The stall speeds for the engines are as</p><p>follows:</p><p>• 224 kw engine - 1,860 to 1,950 rpm</p><p>• 250 kw engine - 1,860 to 1,950 rpm</p><p>Stall Test Procedure</p><p>CAUTION</p><p>DO NOT hold the throttle open for more than 15</p><p>seconds at a time. Permit the engine to operate at</p><p>idle speed for 2 minutes between tests.</p><p>CAUTION</p><p>Release the accelerator immediately if the engine</p><p>speed increases to its governed speed of 2,130</p><p>rpm.</p><p>Transmission Test and Calibration 1300 SRM 1566</p><p>18</p><p>CAUTION</p><p>Performing a stall test in 1st gear may damage the</p><p>internal parts of the drive axle.</p><p>Perform the stall test with the range selector in</p><p>position 3.</p><p>1. Connect a laptop computer to the diagnostic</p><p>plug in the side console. Select the screen to</p><p>read the engine speed.</p><p>2. Place a capacity load on the forks to prevent</p><p>the wheels from turning.</p><p>3. Place the lift truck against an object that</p><p>cannot move.</p><p>4. Apply the brake pedal and release the parking</p><p>brake.</p><p>5. Start the engine and select the 3rd gear in</p><p>manual mode.</p><p>6. Push the accelerator pedal to full throttle.</p><p>7. Read the stall speed and release the throttle</p><p>pedal.</p><p>If the stall speed is 50 to 200 rpm below the</p><p>specification, the engine is not operating at full</p><p>power. Check if engine fault codes are present and</p><p>repair or correct any indicated problems.</p><p>If the stall speed is higher than the specification,</p><p>the engaged clutch(es) may not be holding, or the</p><p>torque converter may be damaged. Check if</p><p>transmission fault codes are present and repair or</p><p>correct any indicated problems.</p><p>If no transmission fault codes are present and the</p><p>stall speed is considerably higher than the</p><p>specification, remove the torque converter for</p><p>inspection.</p><p>If the stall speed is only slightly higher than the</p><p>specification, consider the service life of the torque</p><p>converter and decide whether to replace the torque</p><p>converter immediately or at a later point in time.</p><p>CLUTCH FILLING CALIBRATION</p><p>Description</p><p>The APC controller is programmed to quickly fill the</p><p>clutch area until the piston starts clamping the</p><p>discs, and only then raise clutch pressure further</p><p>within a certain period of time until full</p><p>engagement has been reached.</p><p>When shifting up, the clutch to be released will</p><p>start relieving its pressure at the same moment</p><p>when the engaging clutch starts clamping. For a</p><p>short period of time, the two clutches are both</p><p>partially engaged. This feature allows shifting up</p><p>smoothly under full traction.</p><p>As the clutch plates wear, they will get slightly</p><p>thinner. As the clutch plates get thinner, the piston</p><p>will have longer travel until the piston starts</p><p>clamping the discs. This causes the transmission to</p><p>shift less smoothly until it has been recalibrated.</p><p>The APC controller has a calibration program to</p><p>readjust the clutch filling time and the time to reach</p><p>full engagement. Clutch filling time is determined</p><p>by the elapsed time between clutch fill start and the</p><p>moment when the turbine speed sensor detects a</p><p>change in speed (touch detection). The time to reach</p><p>full engagement is determined by the elapsed time</p><p>between touch detection and full clutch</p><p>engagement. An automatic warning to recalibrate</p><p>the transmission appears on the instrument cluster</p><p>every 2000 hours (tE501). See</p><p>Transmission Exceed Codes.</p><p>The automatic clutch filling calibration requires</p><p>that the pumps connected to the transmission take</p><p>off a constant load from the system. The</p><p>automatically triggered command to recharge the</p><p>brake accumulator will cause an unacceptable load</p><p>increase that will stop the automatic clutch</p><p>calibration. For this reason, a calibration switch,</p><p>located in the side console, has been installed to</p><p>disable the accumulator charging function to</p><p>prevent interference of the automatic clutch</p><p>calibration. Also, any inadvertent operation of a</p><p>hydraulic function will cause an unacceptable load</p><p>increase and will stop the automatic clutch</p><p>calibration.</p><p>During clutch calibration, codes may be displayed</p><p>that indicate incorrect conditions for proper clutch</p><p>calibration. The explanation of these codes is in</p><p>APC200 Fault Code Guide 1300SRM1435 or</p><p>SPN / FMI Code Guide 9000SRM2046.</p><p>During clutch calibration, fault codes with a</p><p>preceding E’ may be displayed (for example: E1.25).</p><p>The first digit after the E’ can be a 1’ or a 2’. 1’</p><p>relates to faults during clutch filling time. 2’ relates</p><p>to faults during clutch engagement. The last two</p><p>digits indicate calibration faults, which are listed</p><p>and explained in APC200 Fault Code Guide</p><p>1300 SRM 1566 Transmission Test and Calibration</p><p>19</p><p>1300SRM1435 or SPN / FMI Code Guide</p><p>9000SRM2046.</p><p>Procedure</p><p>1. Apply the parking brake.</p><p>2. Connect a laptop computer to the diagnostic</p><p>plug in the side console.</p><p>3. Place the calibration switch in the down</p><p>position.</p><p>4. Make sure the shift lever is in NEUTRAL or</p><p>REVERSE for lift trucks with a shift lever.</p><p>5. Start the engine.</p><p>6. Make sure the transmission oil temperature is</p><p>at least 60°C (140°F).</p><p>7. Select the Settings’ icon from the side tool bar,</p><p>next select the Automatic Calibration’ icon,</p><p>then select the Transmission Calibration’ icon.</p><p>8. The automatic calibration starts when the shift</p><p>lever or MONOTROL® is moved into the</p><p>FORWARD position and the transmission oil</p><p>temperature is at least 60°C (140°F).</p><p>9. When transmission oil temperature is below</p><p>60°C (140°F), the automatic calibration</p><p>program will first heat the transmission before</p><p>proceeding with the calibration. This feature is</p><p>part of the calibration program process. DO</p><p>NOT interfere with the calibration program</p><p>process, as interference will stop the</p><p>calibration.</p><p>10. The complete automatic calibration process</p><p>takes 12 to 15 minutes. The screen will show</p><p>"donE" when the calibration has been</p><p>completed. The engine speed will remain at idle</p><p>during calibration.</p><p>11. Switch the key switch OFF after the laptop</p><p>screen indicates that the calibration is</p><p>complete.</p><p>12. Place the calibration switch in the up position.</p><p>NOTE: DO NOT interfere with the calibration.</p><p>Activating any controls or components will stop the</p><p>calibration mode before completion. The screen will</p><p>show when the calibration is complete.</p><p>During calibration, the APC216 display may show</p><p>calibration condition messages or error codes. See</p><p>APC200 Fault Code Guide 1300SRM1435 or</p><p>SPN / FMI Code Guide 9000SRM2046.</p><p>INCHING CALIBRATION</p><p>Description</p><p>Inching is a controlled traction and braking mode. It</p><p>enables higher engine speeds, resulting in increased</p><p>hydraulic function speeds, while the lift truck travel</p><p>speed remains low. The inching function is obtained</p><p>by relating the inching pedal position to clutch</p><p>pressure. The relation between pedal position and</p><p>clutch pressure results in the natural reaction of the</p><p>operator to depress the inching pedal further when</p><p>the actual lift truck speed is too high. A further-</p><p>depressed inching pedal causes the pressure in the</p><p>slipping clutch to lower, which reduces lift truck</p><p>speed regardless of engine speed. If excessive heat is</p><p>generated during</p><p>inching, the APC controller will</p><p>release all pressure and show fault code 46.05.</p><p>The inching pedal sensor must be calibrated for two</p><p>pedal positions: inching pedal completely depressed,</p><p>and inching pedal released. Calibration is required</p><p>when the inching sensor has been replaced, or when</p><p>it becomes loose. Calibration is also required</p><p>annually, due to wear and creep of pedals and</p><p>linkages. Before calibrating the inching sensor,</p><p>verify the adjustment of the brake pedal and the</p><p>inching sensor. Incorrect sensor calibration triggers</p><p>fault codes during operation. By slightly varying the</p><p>free travel of the brake pedal, it is possible to vary</p><p>the moment when brakes are applied. An early</p><p>brake application will result in excessive heat being</p><p>generated in the inching clutch and in the brakes. A</p><p>delayed brake application results in longer pedal</p><p>travel time before the brakes are fully applied.</p><p>Always make small adjustments in the free travel of</p><p>the brake pedal and make sure there is adequate</p><p>distance between the pedals and the floor plate</p><p>when the pedals are in the fully-applied/depressed</p><p>position.</p><p>Transmission Test and Calibration 1300 SRM 1566</p><p>20</p><p>Pedal and Sensor Adjustment for Braking</p><p>and Inching for B/C917, G/H117 and C/</p><p>D222.</p><p>1. Adjust the adjustment bolt located behind the</p><p>pedal on the brake pedal assembly so that the</p><p>roller has contact with the capscrew on the</p><p>valve and there is no play. See Figure 14.</p><p>1. BRAKE PEDAL</p><p>2. INCHING PEDAL</p><p>3. ADJUSTMENT BOLT FOR BRAKE PEDAL</p><p>4. ADJUSTMENT BOLT FOR BRAKE PEDAL</p><p>COUPLING</p><p>5. ADJUSTMENT BOLT FOR INCHING PEDAL</p><p>Figure 14. Brake Pedal Assembly</p><p>2. Adjust the adjustment bolt located behind the</p><p>inching pedal on the inching pedal assembly so</p><p>that the inching pedal is at the same level as</p><p>the brake pedal when both pedals are in the</p><p>released (pedal up) position. See Figure 14.</p><p>3. Adjust the adjustment bolt for the inching/</p><p>brake pedal coupling so that the inching pedal</p><p>has no play. Both pedals should move together</p><p>when the inching pedal is applied. The</p><p>additional spring installed under the inching</p><p>pedal provides flexibility when adjusting the</p><p>brake/inching overlap. See Figure 14 and</p><p>Figure 15.</p><p>Figure 15. Brake Inching Pedal Adjustment</p><p>Inching Pedal Sensor Adjustment</p><p>Not for A404</p><p>NOTE: When the inching pedal is not activated and</p><p>in the released (pedal up) position, the analog</p><p>output of the inching pedal sensor should be</p><p>between 600 and 700 mV.</p><p>NOTE: A slight preload of the potentiometer arm is</p><p>required to achieve the output voltage for the</p><p>inching pedal in the released (pedal up) position.</p><p>Use Dana Dashboard software to check the output</p><p>voltage.</p><p>1. Connect a laptop computer to the diagnostic</p><p>plug in the side console.</p><p>2. Turn the key switch to the ON position.</p><p>3. Select Inching Pedal Calibration Mode.</p><p>4. Make sure the analog input of the inching</p><p>pedal sensor is between 600 and 700 mV when</p><p>the pedal is in the pedal up position.</p><p>1300 SRM 1566 Transmission Test and Calibration</p><p>21</p><p>5. If the analog input is not within specifications,</p><p>proceed as follows:</p><p>a. Raise the cab until the latch locks in the</p><p>partially open position. Refer to the manual</p><p>Operator's Cab 0100SRM1390 or</p><p>Operator's Cab 0100SRM2043.</p><p>b. Loosen the two inching pedal sensor-</p><p>mounting capscrews. See Figure 16.</p><p>c. Rotate the inching pedal sensor in the</p><p>slotted holes located beneath the inching</p><p>pedal until the output voltage of the released</p><p>(pedal up) position inching pedal is between</p><p>600 and 700 mV.</p><p>d. Tighten the two sensor-mounting capscrews</p><p>and make sure the output voltage of the</p><p>inching pedal sensor is between 600 and 700</p><p>mV, with the inching pedal in the released</p><p>(pedal up) position.</p><p>6. Turn the key switch to the OFF position.</p><p>7. Disconnect the laptop computer from the</p><p>diagnostic plug.</p><p>1. SENSOR-MOUNTING CAPSCREW</p><p>2. INCHING PEDAL SENSOR</p><p>Figure 16. Sensor Adjustment</p><p>Pedal and Sensor Adjustment for Braking</p><p>and Inching on A404</p><p>1. Verify that the brake pedal has no free travel</p><p>between the positions brake pedal released and</p><p>when brake pedal is lifted up by hand.</p><p>2. If required, turn the brake pedal adjustment</p><p>bolt to remove free travel. See Figure 17.</p><p>3. Verify that the angle between brake pedal and</p><p>cab floor is between 132° and 142° when the</p><p>brake pedal is released.</p><p>4. If required, remove the brake valve and add</p><p>additional shims between brake valve and cab</p><p>floor. Apply Loctite to the threads of the valve</p><p>mounting bolts and torque to</p><p>20 N•m (15 lbf ft). Release the brake pedal</p><p>adjustment bolt and re-adjust to remove free</p><p>travel.</p><p>5. Verify that the brake switch switches ON after</p><p>2° to 6° pedal rotation, or 5 mm to 15 mm pedal</p><p>travel, measured at the tip of the brake pedal.</p><p>6. If required, loosen the brake switch mounting</p><p>bolts, move the switch into the correct position</p><p>and retighten the bolts.</p><p>7. Adjust the inching pedal adjustment bolt to</p><p>align the inching pedal with the brake pedal.</p><p>8. Adjust the coupling bolt under the inching</p><p>pedal to remove play between inch pedal</p><p>coupling bolt and brake pedal coupler. Make</p><p>sure that both brake and inching pedal travel</p><p>at the same time when the inching pedal is</p><p>applied.</p><p>9. Verify that the Start Enable Switch switches</p><p>ON after 10° to 14° of inching pedal rotation. If</p><p>required, loosen the mounting bolts of the Start</p><p>Enable Switch, move the switch into the correct</p><p>position and retighten the bolts.</p><p>10. Use the Dana Dashboard software to measure</p><p>inching sensor signals.</p><p>11. Verify that the inching sensor input signal is</p><p>5.0 Volt +/- 0.1 Volt with the key switch in the</p><p>ON position.</p><p>Transmission Test and Calibration 1300 SRM 1566</p><p>22</p><p>12. With the inching pedal released, the inching</p><p>sensor output voltage should be between 0.6</p><p>and 0.7 volt.</p><p>13. When the pedal is fully depressed, the inching</p><p>sensor output voltage should be between 3.7</p><p>and 3.9 volt.</p><p>14. If required, loosen the adjustment bolts of the</p><p>sensor mounting plate, move the mounting</p><p>plate with the sensor into the correct position</p><p>and retighten the bolts.</p><p>15. Recalibrate the inching sensor. See</p><p>Inching Sensor Calibration.</p><p>16. Turn the key switch to the OFF position.</p><p>Inching Sensor Calibration</p><p>1. Make sure the pedals and the inching sensor</p><p>have been correctly adjusted.</p><p>2. Connect a laptop computer to the diagnostic</p><p>plug at the fuse panel.</p><p>1. BOLT</p><p>2. BRAKE SWITCH</p><p>3. BRAKE PEDAL ADJUSTMENT BOLT</p><p>4. SHIM</p><p>5. BRAKE VALVE MOUNTING BOLT</p><p>6. BRAKE VALVE</p><p>7. INCHING PEDAL ADJUSTMENT BOLT</p><p>8. INCHING SENSOR MOUNTING PLATE</p><p>9. INCHING SENSOR ADJUSTMENT BOLT</p><p>10. INCHING SENSOR</p><p>11. START ENABLE SWITCH</p><p>12. COUPLING BOLT</p><p>Figure 17. Adjustment for Braking and Inching</p><p>1300 SRM 1566 Transmission Test and Calibration</p><p>23</p><p>3. Turn the key switch to the ON position.</p><p>4. Use the Automatic Calibration’ mode of the</p><p>Dana Dashboard program.</p><p>5. Select the Inching Pedal Calibration’ mode of</p><p>the Dana Dashboard program and follow the</p><p>instructions.</p><p>6. The following must be calibrated with the key</p><p>switch in the ON position:</p><p>• Fully released pedal (600- 700 mV)</p><p>• Fully depressed pedal (2500-4000 mV)</p><p>• (3500 - 4000 mV). A practical maximum value</p><p>is 3900 mV.</p><p>7. Check the inching percentage of the</p><p>transmission by using the Dana Dashboard</p><p>program. When the pedal is released, the</p><p>inching percentage should be at 0%. Readjust</p><p>the inching sensor if the inching percentage</p><p>deviates from zero and repeat the inching</p><p>sensor calibration.</p><p>8. Exit the Dashboard program.</p><p>9. Turn the key switch to the OFF position.</p><p>10. Disconnect the laptop computer from the</p><p>diagnostic plug.</p><p>Electrical Specifications</p><p>ELECTRICAL SPECIFICATIONS</p><p>Electronic controlled modulation solenoids</p><p>1 VFS 2nd/4th - VFS 1st/3rd - VFS Fwd - VFS</p><p>Rev:</p><p>2 Coil resistance - 4.35 ±0.35Ω at 25°C (77°F)</p><p>ON/OFF solenoids</p><p>1 Total neutral, 1st/3rd and 2nd/4th range</p><p>solenoid:</p><p>2 Coil resistance - 12V - 28 ±2Ω at 20°C (68°F)</p><p>3 Coil resistance - 24V - 87 ±2Ω at 20°C (68°F)</p><p>Speed sensor</p><p>1 Type - Magneto resistive sensor.</p><p>2 Sensing distance - 0 to 1.8 mm (0 to 0.07 in.)</p><p>3 Sensor signal - Generates a square current</p><p>with a fixed amplitude changing between 7</p><p>and 14 mA.</p><p>Table 4. Temperature Sensor (In Speed Sensor)</p><p>Resistance Versus Temperature</p><p>Ambient Temperature Resistance</p><p>Ω</p><p>−30°C (−22°F) 1247</p><p>−20°C (−4°F) 1367</p><p>Ambient Temperature Resistance</p><p>Ω</p><p>−10°C (14°F) 1496</p><p>0°C (32°F) 1630</p><p>10°C (50°F) 1772</p><p>20°C (68°F) 1922</p><p>25°C (77°F) 2000</p><p>30°C (86°F) 2080</p><p>40°C (104°F) 2245</p><p>50°C (122°F) 2417</p><p>60°C (140°F) 2597</p><p>70°C (158°F) 2785</p><p>80°C (176°F) 2980</p><p>90°C (194°F) 3182</p><p>100°C (212°F) 3392</p><p>110°C (230°F) 3607</p><p>120°C (248°F) 3817</p><p>125°C (257°F) 3915</p><p>Electrical Specifications 1300 SRM 1566</p><p>24</p><p>APC200 Display Information</p><p>GENERAL</p><p>NOTE: The APC312 controller installed on truck</p><p>series A404 does not include a display. Information</p><p>as provided on the APC216 display must be read</p><p>either through a lap top computer or through the</p><p>A404 Display.</p><p>The APC216 controller is located in the side console</p><p>of the cab. The APC216 controller has a display and</p><p>push buttons to call off information. See Figure 18.</p><p>The information is provided by means of codes. The</p><p>interpretation of these codes depends on the display</p><p>mode being activated. The following display modes</p><p>are available:</p><p>• General Information</p><p>• Test</p><p>• Calibration</p><p>These display modes provide an alternative method</p><p>to calibrate or obtain information if the Dana</p><p>Dashboard software is not available.</p><p>The LED lamp labeled D’ is yellow and will be ON</p><p>to indicate diagnostic modes.</p><p>The LED lamp labeled E’ is yellow and blinks to</p><p>indicate faults.</p><p>The LED lamp labeled F’ is red and is ON when the</p><p>APC200 is in the reset condition.</p><p>The push button marked M’ is used to scroll to one</p><p>of the three display groups.</p><p>The push button marked S’ is used to scroll to the</p><p>next sub group within a display group. See Table 5.</p><p>Figure 18. APC200 Front Panel</p><p>GENERAL INFORMATION GROUP</p><p>Table 5 shows the structure of the General</p><p>Information Group. Figure 19 schematically shows</p><p>that by pressing the M button, the display scrolls to</p><p>the next display group, and by pressing the S button</p><p>the display scrolls to the next sub group. When the</p><p>M button is pressed to scroll to the next display</p><p>group, the display will first show the sub group that</p><p>is highest on the display group list (GPoS, or cPoS,</p><p>or Err). From the sub group that is highest on the</p><p>display group list, it is possible to scroll to sub</p><p>groups that are lower on the sub group list. To</p><p>return to the highest positioned sub group, press the</p><p>S button after having reached the lowest positioned</p><p>sub group.</p><p>To scroll to the next display group, first scroll to the</p><p>sub group (GPoS, or cPoS, or Err) that is highest on</p><p>the display group list. It will only be possible to</p><p>scroll to the next display group by pressing the M</p><p>button by starting in the GPoS, cPoS, or Err display</p><p>group.</p><p>To read the value of a sub group, press and release</p><p>the S button. After half a second, the display will</p><p>show the code of the sub group, followed by the</p><p>actual measured value. See Table 5 for sequence</p><p>and explanation of the sub groups.</p><p>After startup, the display will show the sub group</p><p>that was selected when the APC216 was switched</p><p>OFF.</p><p>Figure 19. APC200 Display Groups</p><p>1300 SRM 1566 APC200 Display Information</p><p>25</p><p>Table 5. General Information Group</p><p>Display Description Explanation Example</p><p>Gear, Vehicle Speed, Distance</p><p>GPoS Gear Position Shows the actual engaged gear direction (F, R) and range</p><p>(1, 2, 3). F3</p><p>USPd Vehicle Speed Shows the lift truck speed in 0.1 km/hr resolution. 167</p><p>diSt Travel Distance</p><p>Shows the traveled distance in 0.1 km resolution. 1258</p><p>Press the S button within 3 seconds to reset to zero.</p><p>oPEr Operating Hours</p><p>Shows the total lift truck running hours in one hour</p><p>resolution, and has a range of 0 to 49999 hours. The</p><p>number digits show the hours, the number of dots in</p><p>between show the number of times 10000 hours needs to be</p><p>added to the number shown.</p><p>12.3.4.</p><p>Lever Position, Transmission Speed, Temperature</p><p>cPoS Shift Lever</p><p>Position Shows the current shift lever position (F, R) (1, 2, 3). F3</p><p>ESPd Engine Speed Shows the measured engine speed. 1580</p><p>tSPd Turbine Speed Shows the measured turbine speed. 885</p><p>oSPd Output Speed Shows the measured output speed. 600</p><p>SrAt Speed Ratio Shows the speed ratio, and turbine/engine speed. 0.56</p><p>tq I Turbine Torque Shows the measured turbine torque at transmission input</p><p>side in N•m. 125</p><p>ttnP Transmission</p><p>Temperature Shows the transmission temperature in °C. 65</p><p>ctnP Cooler in</p><p>Temperature Shows the cooler input temperature in °C. 75</p><p>Fault Codes</p><p>Err Fault Code Shows the transmission fault code number. 31.01</p><p>APC200 Display Information 1300 SRM 1566</p><p>26</p><p>FAULT CODES</p><p>When the M button is pushed to scroll to the fault</p><p>code group (Err), the display normally shows - - - -’,</p><p>to indicate that no faults are active. When the E-</p><p>LED is blinking, a fault is active and will be shown</p><p>on the display.</p><p>If more than one fault has been detected, the most</p><p>severe fault will be shown first. Push and release</p><p>the S button once to display the next fault code.</p><p>After the last code has been displayed, the display</p><p>will show - - - -’.</p><p>Displayed fault codes either appear blinking, or are</p><p>shown uninterrupted. When shown uninterrupted,</p><p>the fault code is active. When blinking, the fault has</p><p>occurred but is currently inactive.</p><p>Once an inactive fault code has been displayed, it</p><p>will not be shown again. Write down the codes of</p><p>inactive faults, or refer to the dashboard display.</p><p>The memory of the dashboard display retains all</p><p>fault codes until its memory has been cleared.</p><p>INDICATION OF PROTECTION MODES</p><p>The Limp Home Mode and Shutdown Mode as</p><p>described under Control System’ are only made</p><p>visible on the APC200 display when it is in the</p><p>GPoS- or cPoS-mode. The display shows LH’ for</p><p>Limp Home, or Sd’ for Shut Down, and also the</p><p>direction and the gear selected at that moment.</p><p>Once in the Shut Down mode, the APC200 will</p><p>already have selected NEUTRAL. The E-LED on</p><p>the APC200 front panel will be blinking. See</p><p>Figure 20.</p><p>Figure 20. Indication of Protection Mode</p><p>TEST FUNCTION GROUP</p><p>To enter the Test Function Group, press the S</p><p>button while turning the key switch to ON. Release</p><p>the S button when the display shows: 8.8.8.8.’. After</p><p>releasing the S button the display will show: diSP’.</p><p>See Figure 21.</p><p>Figure 21. Test Function Group Mode</p><p>The only way to leave the test function group is by</p><p>switching the key switch to OFF.</p><p>Figure 22 schematically shows that by pressing the</p><p>M button the display scrolls to the next display</p><p>group, and by pressing the S button the display</p><p>scrolls to the next sub group. When the M button is</p><p>pressed to scroll to the next display group, the</p><p>display will first show the sub group that is highest</p><p>on the display group list (diSP, dinP, etc.). Starting</p><p>from these positions, it will be possible to scroll to</p><p>sub groups that are lower on the sub group list. To</p><p>return to the highest positioned sub group, press the</p><p>S button after having reached the lowest positioned</p><p>sub group.</p><p>To scroll to the next display group, first scroll to the</p><p>sub group (diSP, dinP, etc.) that is highest on the</p><p>display group list. Only when starting at diSP, dinP,</p><p>etc., will it be possible to scroll to the next display</p><p>group by pressing the M button.</p><p>Instructions for how to call off information for each</p><p>test group are described separately.</p><p>1300 SRM 1566 APC200 Display Information</p><p>27</p><p>Figure 22. Test Function Group Schematic</p><p>APC200 Display Information 1300 SRM 1566</p><p>28</p><p>DIGITAL INPUT TEST</p><p>The APC216 has 10 digital inputs which measure</p><p>connectivity of the wires listed in Table 6. After the</p><p>display has shown dinP’ (see Figure 23), push and</p><p>release the S button. The display indicates the</p><p>active inputs by switching ON certain segments of</p><p>the display (see Figure 24). The numbered segments</p><p>0-9 represent the digital inputs DIGIN0 through</p><p>DIGIN9.</p><p>Table 6. Digital Input Test</p><p>Code Wire</p><p>Name</p><p>APC200</p><p>Wire Nr</p><p>APC200</p><p>Pin Nr</p><p>Wire</p><p>Description Output</p><p>0.12 DIGIN0 A12 B2 Shift Lever 1st hi/lo</p><p>1.13 DIGIN1 A13 C2 Shift Lever 2nd hi/lo</p><p>2.14 DIGIN2 A14 D2 Seat Occupied, Switch Re-</p><p>lay hi/lo</p><p>3.17 DIGIN3 A17 G2 OPEN lo</p><p>4.18 DIGIN4 A18 H2 Shift Lever Forward hi/lo</p><p>5.19 DIGIN5</p>