Perda de carga de tubulações de pequeno diâmetro

de Agricultura “Luiz de Queiroz”, Universidade 
de São Paulo, Piracicaba, 1990. 
BAGARELLO, V. et al. Experimental study on flow-
resistance law for small-diameter plastic pipes. J. Irrig. 
Drain. E. - ASCE, New York, v. 121, n. 5, p. 313-316, 
1995. 
BERNUTH, R.D. von. Discussion of “Hydraulic friction 
factors for pipe flow”. J. Irrig. Drain. E. - ASCE, New 
York, v. 115, n. 5, p. 916-918, 1988. 
BERNUTH, R.D. von. Simple and accurate friction loss 
equation for plastic pipe. J. Irrig. Drain. E. - ASCE, New 
York, v. 116, n. 2, p. 294-298, 1990. 
BERNUTH, R.D. von; WILSON, T. Friction factors for 
small diameter plastic pipes. J. Hydraul. Eng. - ASCE, New 
York, v. 115, n. 2, p. 183-192, 1989. 
BOMBARDELLI, F.A.; GARCIA, H. Hydraulic design of 
large-diameter pipes. J. Hydraul. Eng. - ASCE, New York, 
v. 129, n. 11, p. 839-846, 2003. 
CAMARGO, A.P.; SENTELHAS, P.C. Avaliação do 
desempenho de diferentes métodos de estimativa da 
evapotranspiração potencial no Estado de São Paulo, 
Brasil. Rev. Bras. Agrometeorologia, Santa Maria, v. 5, n. 1, 
p. 89-97, 1997. 
FRIZZONE, J.A. et al. Caracterização hidráulica de um 
tubo gotejador. Rev. Bras. Eng. Agric. Ambient., Campina 
Grande, v. 2, n. 3, p. 278-283, 1998. 
HATHOOT, H.M. et al. Analysis and design of trickle-
irrigation laterals. J. Hydraul. Eng. - ASCE, New York, 
v. 119, n. 5, p. 756-767, 1993. 
KAMAND, F.Z. Hydraulics friction factors for pipe flow. 
J. Irrig. Drain. E. - ASCE, New York, v. 114, n. 2, p. 311-
323, 1988. 
McENROE, B.M. Discussion of “Hydraulic friction 
factors for pipe flow”. J. Irrig. Drain. E. - ASCE, New 
York, v. 115, n. 5, p. 915-916, 1989. 
PORTO, R.M. Hidráulica básica. São Carlos: EESC/USP, 
1998. 
ROMEO, E. et al. Improved explicit equations for 
estimation of the friction factor in rough and smooth 
pipes. Chem. Eng. J., Amsterdam, v. 86, n. 3, p. 369-374, 
2002. 
SERGHIDES, T.K. Estimate friction factor accurately. 
Chem. Eng. J., Amsterdam, v. 91, n. 5, p. 63-64, 1984. 
SONNAD, J.R.; GOUDAR, C.T. Turbulent flow 
friction factor calculation using a mathematically exact 
alternative to the Colebrook-White equation. J. Hydraul. 
Eng. - ASCE, New York, v. 132, n. 8, p. 863-867, 2006. 
SWAMEE, P.K.; JAIN, A.K. Explicit equations for pipe-
flow problems. J. Hydraul. Division - ASCE, New York, 
v. 102, n. 5, p. 657-664, 1976. 
VILELA, L.A.A. et al. Alteração no diâmetro de tubos de 
polietileno submetidos a diferentes pressões. Rev. Bras. 
Eng. Agric. Ambient., Campina Grande, v. 7, n. 1, p. 182-
185, 2003. 
YOO, D.H.; SINGH, V.P. Two methods for the 
computation of commercial pipe friction factors. J. 
Hydraul. Eng. - ASCE, New York, v. 131, n. 8, p. 694-704, 
2005. 
WILLMOTT, C.J. On the validation of models. Phys. 
Geogr., New York, v. 2, n. 2, p. 184-195, 1981. 
 
 
Received on March 05, 2007. 
Accepted on August 06, 2007.